Unless given, use the: POLAR FORM for voltage and current, RECTANGULAR FORM for impedance. Consider the following circuit, supplied by a 10VRMS current source with a 0° phase shift (i.e. Vsource = 1020° V). R2 100 Q V sine C /R1 100 Q 16 μF 50 Hz L 320 mH a. What is the total impedance of the circuit? b. Is the circuit inductive, capacitive, or neither (resistive)? c. What is the total power (apparent) delivered by the current source? d. Draw the phasor diagram of the voltage and current at the source. e. What is the current passing through the R2 and L branch? f. Draw the phasor diagram of the voltage and current at the R2 and L branch.

Unless given, use the: POLAR FORM for voltage and current, RECTANGULAR FORM for impedance. Consider the following circuit, supplied by a 10VRMS current source with a 0° phase shift (i.e. Vsource = 1020° V). R2 100 Q V sine C /R1 100 Q 16 μF 50 Hz L 320 mH a. What is the total impedance of the circuit? b. Is the circuit inductive, capacitive, or neither (resistive)? c. What is the total power (apparent) delivered by the current source? d. Draw the phasor diagram of the voltage and current at the source. e. What is the current passing through the R2 and L branch? f. Draw the phasor diagram of the voltage and current at the R2 and L branch.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Similar questions

A chopper circuit has an inductive load of 2ohm resistance and 10mH inductance. If the source voltage is 20 V and the frequency of the chopper is set to 100Hz and the on-time to 5 ms. Determine the average voltage and current, maximum and minimum load currents.
What impedance vector (0- j15) Ohms represents:A. A pure resistance. C. A pure capacitance.B. A pure inductance. D. An inductance combined with a capacitance.
What impedance vector - j25 represents:A. A pure resistance. C. A pure capacitance.B. A pure inductance. D. An inductance combined with a resistance.
A certain impedance is given by 1012° N. Does the current lead or lag the voltage, and by how many degrees? Fill in the blanks. The current the voltage by
For a series RLC circuit with a sinusoidal input voltage, the amplitude of the current passing through the circuit (I, in mA) is plotted as a function of frequency for two cases: Curve 1 with R1, L1. and Curve 2 with R2. L2 as shown in the next figure. The value of the capacitor used in the circuits is C=0.01 micro Farads. If the value of R2 =1600 Ohm then the input voltage (in volts) is: 7.5 25 110 Frequency H2 O a. 4 O b. 16 sin(9888 t) O c. 8 O d. 8 cos(6.28 f t) O e. 8 sin (6.28 R t)
Determine the capacitance and voltages (Vrms) across the resistor and capacitor and prove that the phasor sum of the series components is equal to the source voltage. Also, solve for its total circuit impedance and total circuit current.
A resistor & a capacitor are connected in series across 230V, ac supply. The current taken by the circuit is 4 A for 50 Hz frequency. The current is reduced to 2 A, when the frequency of supply is decreased to 40 Hz. Determine the value of resistor & the capacitor.
A circuit consisting of a resistor in series with a capacitor takes 100 watts at a power factor of 0.5 form a 100 V, 60 Hz supply. Find the current, resistance, the impedance and the capacitance.
A capacitor "C", an inductor "L" and a switch "S" are connected in series. When the switch is open, the plate to the left of the capacitor has charge "Qo". The switch is closed the load and current vary sinusoidally with time. Represent graphically the load "Qo" and the intensity of current "I" as a function of time "t", and explain why the current leads the load by a phase difference of 90°.
A DC-DC Chopper Circuit with an RL Load has an output current waveform shown below with a duty cycle of 50% and 1ms period. If it has a resistance of lohm and an inductance of 10mH, find the source voltage. output 5A -current 2A ten toff
An electrical circuit with a sinusoidal voltage source, a resistor, and a capacitor all connected in series. The voltage across the capacitor: Select one: a. Leads the current in the capacitor by exactly 90o b. Is in phase with the sinusoidal voltage source c. Is in phase with the voltage across the resistor d. Leads the current in the circuit by 90o e. Lags the current in the circuit by 90o
Ac - 100 VrmsR1 - 1kR2 - 500Rload - 1kCapacitor - 2uF Q1. How much is the capacitor voltage lagging from the AC source