For the circuit shown in the image: • What is the value of Sa, Sɛ, Sc, Sp and Srotal (give answer in a complex number in rectangular form) • What is the power factor of the circuit. (give answer in a real number) What is the value of the impedance that the source sees (give answer in a complex number in rectangular format). B) 200 KVAR fp= 0,80 leading A) 115 kW C) 180 kVA D) 180 KVAR 120230° (+ fp= 0,60 lagging fp= 0,50 lagging fp= 0,70 leading

For the circuit shown in the image: • What is the value of Sa, Sɛ, Sc, Sp and Srotal (give answer in a complex number in rectangular form) • What is the power factor of the circuit. (give answer in a real number) What is the value of the impedance that the source sees (give answer in a complex number in rectangular format). B) 200 KVAR fp= 0,80 leading A) 115 kW C) 180 kVA D) 180 KVAR 120230° (+ fp= 0,60 lagging fp= 0,50 lagging fp= 0,70 leading

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
ESSAY: Describe what happens to the power in this RLC series circuit as the capacitance decreases. Explain in general terms why the observed change should occur. Understand the effects of basic electrical components on the average power of the system and the concept of power factor. Differentiate between average power and real power.
A 220 Ω resistor is in series with an 80 mH inductor. The AC source is 48 at 1 kHz. The power factor is ________. Hint: Draw the circuit and get Vs and Is
2. Refer to the Figure 2. a) Determine the total impedance of the circuit in polar form. b) Determine the voltage v(t) and current i(t) sinusoidal forms. Sketch one cycle of the waveforms in the same x-axis. Clearly indicating the peak value and the period of each waveform and the phase difference (in milliseconds) between the two waveforms. c) Determine the values of resistance R and inductance L. d) Determine the phasors V,, VR and Vc. e) Sketch the phasor diagram showing Vs, Vr, Vr, Vc and I.
15. You are working on a power factor correction installation, and you notice with a clip-on ammeter as you add in capacitance the current drops, you add more capacitance and the current drops, you add more capacitance the current rises. How do you know when you are at unity power factor?
Quistion.4. a) A sinusoidal voltage is applied to the resistive circuit in figure.Q.4. a. Determine the following: i. Ims ii. Iavg iii. Ip iv. Ipp 10V 1.0 ΚΩ Figure.Q.4.a
An inductive impedance made up of a resistor and an inductor has the characteristic that its currentadvances in phase to the voltage at the impedance A) lags in phase with the voltage across the impedance B) is in phase with the voltage across the impedance. C) None of the above
A 15ohms resistor connected in parallel with an impedance of 8 - j2 across an AC source. The entire circuit takes a total average power of 2000 watts. What is the average power in the 15ohms resistor?
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms
Impedance of AC circuit and Admittance of AC circuitSHOW THE CIRCUIT USING ANY SOFTWARE OR YOU CAN DRAW IT MANUAALYY thNAKSS