83 AE = 8 cm AB = BC=CD=DE=6 cm 02=120° Os =1 rad/sec Os = 90° 02= 2 rad/sec Find the acceleration of point C of the 5-bar mechanism shown in question 2 by using an acceleration polygon if crank AB is rotating with a speed of 2 rad/sec and ED by 1 rad/sec, both CCW and constant. tfen birini seçin: a. a=5.9 cm/sec? at 128 degrees b. ac=11.8 cm/sec? at 123 degrees c. a=12.6 cm/sec? at 65 degrees d. ac=21.0 cm/sec? at 88 degrees e. ac=21.9 cm/sec? at -63 degrees

83 AE = 8 cm AB = BC=CD=DE=6 cm 02=120° Os =1 rad/sec Os = 90° 02= 2 rad/sec Find the acceleration of point C of the 5-bar mechanism shown in question 2 by using an acceleration polygon if crank AB is rotating with a speed of 2 rad/sec and ED by 1 rad/sec, both CCW and constant. tfen birini seçin: a. a=5.9 cm/sec? at 128 degrees b. ac=11.8 cm/sec? at 123 degrees c. a=12.6 cm/sec? at 65 degrees d. ac=21.0 cm/sec? at 88 degrees e. ac=21.9 cm/sec? at -63 degrees

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Handwriting not allow please And give me complete answer
a. What is the ideal mechanical advantage of this system? The inclined plane dimensions are 7.2 meters length and 1.8 meters height.b. What effort force is required to move the 600N create? c. In practice, you need to supply an effort force of 75 N to lift the crate. What is the efficiency?d. How could you redesign this compound machine so that the effort force needed was 50 N in practice? Assume the efficiency is your response from part C no matter what changes you make. Be specific with the changes you propose (if you add pulleys state how many, if you change the inclined plane dimensions state the new dimensions, etc.).
I need answer within 20 minutes please please with my best wishes
hello did you forgot the T in solving Wrev?
See the attached image1) A long rod in the shape of a circular cone is rotating with constant angular velocity c about an axis located at the left end of the rod as shown in the figure below. The bar has length L, major and minor diameters D and d, respectively, and its material has linear elastic behavior with modulus of elasticity E. The values of the problem parameters must be defined by the student a) From the balance of a differential member of the bar, derive the differential equation of balance for the bar. Solve the equation analytically to obtain the bar displacement field, U(X). Give the expression for the displacement at the free end of the member. b) Implement a computational code in MATLAB (or any other software) to solve this problem with "n" two-node bar finite elements. c) Run different simulations by increasing the number of finite elements in each simulation. At each simulation, obtain the displacement of the free end of the member. Graphically compare your results…
3
We have a rectangular piece. We wish to manufacture a parallel slot along thepiece in a vertical milling machine and 50 cm from the edge. The width of the slot is 40 mm. TheDepth of the slot is 25 mm. For this, several rough cutting steps and aFine cut with a depth of 0.20 mm. The depth for each of the steps ofrough cut is limited to 1.75 mmAditional information:What is the number of blades used for the rough cutting steps?What is the number of blades used for the fine cutting step?
Choose 3 of the most important methods, theorems, principles, or concepts from Statics. Write approximately 3-5 coherent sentences about each IN YOUR OWN WORDS, why they are important, and how they are used. No cutting and pasting except perhaps for an equation or two.
Water enters vertically and steadily at a rate of 60 L/s into the sprinkler shown, with unequal arms and unequal discharge areas. The smaller jet has a discharge area of 3 cm2 and a normal distance of 50 cm from the axis of rotation. The larger jet has a discharge area of 5 cm2 and a normal distance of 35 cm from the axis of rotation. Disregarding any frictional effects, determine (a) the rotational speed of the sprinkler in rpm and (b) the torque required to prevent the sprinkler from rotating.
Essay about familiarization on machine
(4) You are interviewing for a job as a see-saw designer. In order to get the job, you must solve a design problem involving a meter-stick with two masses hanging on it (see below). The system is to be perfectly balanced, with the pivot point offset from the center of the meter-stick. The mass of the meter-stick is 65.22 g. To get the job, you must find the unknown mass, m, in grams. 1.00 m F- Fplankt FuiOck, t Foluck0 27.0 cm 13.0 cm 65.22g 500. g 0.63096 나.9 massmissing T= 0,63896(1.0) +.500(-27) +.60 (F) = 0 13.16 grams f =1.289N = 0.1316 9.8 (5) The diagrams show a Fn stationary cargo plane Fn1 Fn2 before and after loading it. What probably happened to make the plane's center of Axis Axis Fg V Fg gravity shift as shown? tne center of gravity moveg tuwaras rne nevavlek Side of tre piane
Must solve all the questions. Otherwise dont attempt it. If attempted partially, i will surely dislike. So solve all questions.