A designer needs a quarter-turn shut-offvalve to flow approximately 10 GPM, withan inlet pressure of 3000 psig and anoutlet pressure of 2900 psig. The flowmedia is clean water at room temperature.She selects a plug valve with a flowcoefficient of 1.20. Is her valve choiceappropriate for the required application?

Answered: A designer needs a quarter-turn valve…

A designer needs a quarter-turn valve to flow approximately 10 GP an inlet pressure of 3000 psig outlet pressure of 2900 psig. TI

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter34: Emission Control Diagnosis And Service

Section: Chapter Questions

Problem 2RQ: What will result from too little EGR flow? And what can cause a reduction in the flow?

See similar textbooks

Related questions

Q: 11. Water at 65 F is pumped to a tank through a 750 ft 12-in diameter galvanized iron pipe

A: Given:Length of pipe=750 ft =228.6 md=12 in =0.3048 mVolume flow rate, Q=5 cfs =0.1415 m3/s

Q: I have a pump that rotates at 1800 RPM, it pumps at a net head of 50 meters a flow rate of 80 lpm,…

Q: Describe the operating principle of a Karman Vortex air flow meter.

A: Flow meter is a measurement device used to measure the flow velocity of the fluid. In Karman Vortex…

Q: Water at 20°C is pumped from Tank A to Tank B (both open to the atmosphere) as shown in Figure 1,…

A: 23.A pump manufacturer's curve has the following details. 1.Total Head, 2.Flow rate, 3.Net positive…

Q: A pump is to be placed at the beginning of a 30 m long piping system consisting of 1-1/2 inch…

A: Release head differs with pull tank level. The response is yes. Assuming you bring down the pull…

Q: 14. The purpose of a crankcase pressure regulator is to D. sp 20. A devi comp and d A. ensure that…

A: Crankcase pressure regulator is a device which prevents overloading of compressor.

Q: A compressor delivers 2000 cfm of air through a pipe at a receiver pressure of 140 psig. What…

Q: If the maximum pressure of a conventional spring relief valve for nitrogen service is 84.3 psia.…

A: Given data: - The maximum spring relief pressure is Pr = 84.3 psia.

Q: Determine the discharge at pipeline 3 in lit/sec assuming f=0.02 for all pipes.

A: Given data Discharge (Q)=0.86m^3/s Friction factor (f) =0.02

Q: Compare a orifice plate for low speed to a Pitot Static Tube.

A: Orifice plate is a flow rate measuring device used for restricting flow, for reducing pressure. It…

Q: mpute the volumetric flow rate (GPM) of ethanol at 77°F that would occur given the above nditions.…

A: In the question, there are losses in the pipe due to - 1. Pipe firction 2. Pipe bending 3. Half…

Q: OIL WITH SP.GR. 0.95 FLOWS AT 200 lit/sec THROUGH 500 METER OF 200 MM DIAMETER PIPE (f =0.0225).

Q: Liquid propane, at its bubble point, is to be pumped from a reflux drum to a depropanizer. The…

Q: Determine the Pressure drop in Mpa through a flow control valve that has a capacity coefficient 5…

A: For a flow control valve the flow rate (Q) is given by - Q=C∆PSpecific Gravitywhere C is capacity…

Q: Determination of Discharge Thru a Siphon

A: Given Height = 83.5 cm To find Theoretical discharge Actual discharge Difference percentage

Q: By increasing the downstream pressure to 125.5 psia, calculate the valve coefficient, Cv and valve…

A: Given Data

Q: The system shown below uses a pump to transfer heavy fuel oil (T= 25°C) from the lower tank to the…

A: Since you have asked a multi-part question, we can provide you the solutions to only first three…

Q: Saturated water at 310K is being pumped from a tank to an elevated tank at the rate of 7L/s. All of…

A: Given-Data:- To-Find:- Power (W)=?

Q: Ex. Closed pipe system the length is 130 m and 50 mm in diameter containing sixteen long elbows and…

A: Write the standard values of pipe fitting losses from pipe fitting losses equivalent length table…

Q: A centrifugal pump consists out of an impeller, diffuser and casing and is powered by 300 kW (shaft…

A: Solution to first three sub-parts as per our company policy:

Q: The effect of introducing orifice plate in the flow meter is

Q: are mea (50p). Water as PA:78 kPa and Ps: 135 kPa. All the pipes are identical. If the total length…

A: Fluid is a state of matter which deforms continuously on the application of force externally,…

Q: Explain major impact all major losses through the pipes.

Q: A "spa tub" is to be designed to replace bath tubs in reno- vations. There are to be 6 outlet…

A: Flow area of the pump is A1=π4D12 The flow rate for the suction is Q=A1v1=π4D12v1⋯⋯⋯(1) Discharge…

Q: Oil at 24 gpm and 1200 psi enters the low-pressure inlet of a 4:1 Racine pressure intensifier. Find…

A: Introduction: The Racine pressure intensifier is used to boost the oil or air exit pressure. It…

Q: (g) volume capacity of compressor in L/s (h) compression ratio (i) clearance volumetric efficiency…

Q: 9. What pressure drop in Ibf/in.? could be expected across a 1.5-in. I.D. orifice with a C4 = 0.70…

A: Given: The inner diameter of pipe, d = 1.5 in The coefficient of discharge, Cd = 0.7 The specific…

Q: WATEVS @ 50°C , Flow From a tank , Throngh 75 cm. Galvanizto Inon ( G.I) pipE the dis charge low oe…

Q: * The advanced flow control valves often have the temperature compensation by increasing the…

A: The compensated flow in a system due to change in temperature can be given as,…

Q: A1/2 in. ball check valve has a hydraulic fluid, with a specific gravity of 0.85 and a kinematic…

Q: A pump is to be placed at the beginning of a 30 m long piping system consisting of 1-1/2 inch…

A: Minor misfortunes in pipe stream are a significant part in computing the stream, tension, or energy…

Q: For flow nate 28 Lis rale Sind pump Power

Q: A pressure relief valve has a power loss across the valve is 11.6 x 10° MJ/sec and flow rate of 5.22…

Q: in fully developed laminar flow (1-4r2/D²), whereris the radi

Q: A pump's shaft is being turned 1,811 rev/min. The pump will ideally produce (no leakage) 39 L/min.…

Q: Calculate (i) the the theoretical ual discharge in m3/s, /s,

A: As per the Bartleby guideline I have solved only three sub part of the problem. However if you…

Q: Determine the Pressure drop in Mpa through a flow control valve that has a capacity coefficient 5…

A: Given: Flow coefficient C=5lpm/kpa1/2Flow rate (Q)=0.0015m3/secSpecific gravity (S.G)=0.85

Q: A centrifugal pump takes brine from the bottom of a supply tank and delivers it into the bottom of…

A: Given: Difference in the level of the supply tank and discharge tank: →Z2-Z1=150 ft Length of the…

Q: n efficiency óf 72%. Thé surface of e friction pressure drop in the pipe

Q: cvclops pow trough a pipeline fic nozzles. Assuming f fthe grese bead Th

Q: Problem 1 consists of ten questions to be solved consecutively. The objective is to pump 280 gal/min…

A: givenQ=280 gal/ minQ=0.028m3/s312,40 such steel pipe ⇒ID⇒90.12mm

Q: Discuss the relation between the head pressure and flow rate for the benefits of connecting the…

A: When the two pumps are connected in series, their resultant pump performance curve is given by…

Q: A surface condenser deals with 12000 kg of steam per hour. Air leakage into the condenser is found…

A: Given: The mass of steam is, m=12000 kg/hr. The mass of air leakage into the condenser is, ma=4…

Q: A pump station has been designed to lift water out of a 6 metre deep pit (vented to atmosphere) via…

A: As per given question we have determine a) Calculate the Net Positive Suction Head (NPSH) for…

Q: Water P, = 15.3083psia, P. = 3206.2psia is pumped through a linear characteristic valve with a…

A: Given data: Pv=15.3083 psiaPc=3206.2 psia∆P=50P1=200 psiaQ=125 gpm Need to check will the valve…

Question

A designer needs a quarter-turn shut-off
valve to flow approximately 10 GPM, with
an inlet pressure of 3000 psig and an
outlet pressure of 2900 psig. The flow
media is clean water at room temperature.
She selects a plug valve with a flow
coefficient of 1.20. Is her valve choice
appropriate for the required application?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2: Solution

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A "spa tub" is to be designed to replace bath tubs in reno- vations. There are to be 6 outlet nozzles, each with a di- ameter of 12 mm, and each should have an outlet velocity of 12 m/s. What is the required flow rate from the single pump that supplies all of these nozzles? If there is one suction line leading to the pump, what is the minimum diameter to limit the velocity at the inlet of the pump to 2.5 m/s?
For the fow rate of 20 liters per minute using the data sheet of the valve. Find the pressure drop. Hint: using orifice formala. Energized 32 cSt/150 sus ol at 40°C A 6.100 A 5.500 4.160 2.40 1420 3.8 15.1 FLOW Ipm o pm PRESSURE DROP ber pa
When using a double acting pressure intensifier for continuous pressure increase, we are looking to have pressure intensified brand operate at 5L/min at 30 MPA. If the main pump can supply 10L/min at 10 MPA, what is the diameter ratio needed between actuator and boosting piston?
How to work out a Bernoulli pipe diameter change to increase or decrease flow into a Ram pump drive pipe. The ram pump selected is a: RAM PO400 with a 80mm drive pipe, will deliver 19200 liters per day to 125m The elevation of ram pump is 334m The elevation of drive inlet pipe is 359m The height being pumped to is 111m
What is the engine speed (in rpm) required for good volumetric efficiency for an engine with two inlet and two exhaust valves, bore of 0.086 m, stroke of 90 mm, inlet air temperature of 330 K, exhaust temperature of 900 K and inlet valve diameter 30 mm (each). Assume specific heat ratio =1.37, R = 287 J/kg.K and an average inlet flow coefficient 0.4. Select one: a. 7013 O b. 6350 O c. 7847 O d. 4620 e. 9202
A Gould Brand, German made Single Reciprocating Compressor has a speed of 1200 rpm. The diameter of the cylinder bore is equal to 120mm and a displacement length of stroke equal to 150mm, at suction pressure of 120KPa with 20 degree centigrade to 215 degree centigrade temperatures. Calculate the following: a. Mass Flow rate, kg/sec b. Pressure Ratio c. Indicated Power d. Shaft Power if Mech'l Eff.=80%
Find the loss in total pressure for each run in the simple duct system of Fig. 1, using the equal-friction method and in English unit. The total pressure available for the duct system is 0.12 in. wg (30 Pa), and the loss in total pressure for each diffuser at the specified flow rate is 0.02 in. wg (5 Pa). Duct fittings are listed in Table 1. Assume the duct dimeter in run 1 is 10 in. and the rest are 8 in. Does the duct system require any adjustment? 150 cfm e. a 15 ft Plenum е 15 ft 5 ft 5 ft a 3. 20 ft 4 10 ft 200 cfm e 10 ft 150 cfm b Duct Fittings for Figure 1 Fittings Type Abrupt Entrance 90 deg Elbow, Pleated Round to Rectangular boot, Straight 45 deg. Converging Wye 45 deg Elbow, Pleated a d e
A simple jet carburetor is required to supply 5 kg of ai and 0.5 kg of fuel per minute. The fuel specific gravity is 0.75. Thrnea'r is initially at 1 bar and 300 K. Calculate the throat diameter or ir choke for a flc ty ocity of 100 m/s. Velocite oefficient is 0.8. If the pressure drop acit 1 1he fuel metering orific orifice diameter assuming. Caf .60 and= 1.4. 80 of that of the choke. calculate
8- Chocking flow condition in convergent nozzle accurse when the back pressure be greater than critical pressure. true false
A Forced - Draft (FDF) with open suction has rated capacity of 4,000 CFM at 1,800 rpm. The pressure developed at the discharged duct is 10 mm H2O. The discharge duct is circular with inside diameter of 600 mm. Calculate the following:a) what is the velocity of air at the discharge in mm H2O?b) what is the theoretical fan power required in kW?Consider standard density of water and air are 1000 kg/m3 and 1.20 kg/m
b) A single stage, single acting reciprocating compressor has a bore of 250 mm and a stroke of 550 mm. It runs at a speed of 300 rev/min. The clearance is 4% of swept volume, and the polytropic index is 1.39 throughout. The intake pressure is 97 kPa at 25°C, and the final compression pressure is 600 kPa. If the free air conditions are 101 kPa and 20°C, determine the free air delivered in m/s.
a) Calculate the interstage pressure ratio per stage for a two-stage compressor if the overall pressure ratio is 10. b) What speed should a single acting, reciprocating compressor run at to produce 50 m³/h of air? The data for the compressor is: Piston diameter = 100 mm, Stroke length = 110 mm,