A "spa tub" is to be designed to replace bath tubs in reno- vations. There are to be 6 outlet nozzles, each with a di- ameter of 12 mm, and each should have an outlet velocity of 12 m/s. What is the required flow rate from the single pump that supplies all of these nozzles? If there is one suction line leading to the pump, what is the minimum diameter to limit the velocity at the inlet of the pump to 2.5 m/s?

A "spa tub" is to be designed to replace bath tubs in reno- vations. There are to be 6 outlet nozzles, each with a di- ameter of 12 mm, and each should have an outlet velocity of 12 m/s. What is the required flow rate from the single pump that supplies all of these nozzles? If there is one suction line leading to the pump, what is the minimum diameter to limit the velocity at the inlet of the pump to 2.5 m/s?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4- A centrifugal pump was tested for cavitation initiation. Total head was 40 m and flow rate were 0.06 m/s. Cavitation started when the total head at the suction side was 3 m. The atmospheric pressure was 760 mm Hg and the vapor pressure at this temperature was 2 kPa. It was proposed to install the pump where the atmospheric pressure is 700 mm Hg and the vapor pressure at the location temperature is 1 kPa. If the pump develops the same total head and flow, can the pump be fixed as the same height as the lab setup? What should be the new height.
Question - You must discuss in detail the way in which the pitot tube and nozzle flow meter are used to calculate velocity or volume flow rate. Write the velocity (or flow rate) equations for both and a detailed description of the what you did.
For the single pump-pipe system below, what will be the changes for the operating point if we increase the pipe size but decrease the shaft speed of the pump? EB H₂ O The operating point will remain the same. O The operating point will occur either at a higher discharge or at a lower discharge, depending on the specific influence of each change. O The operating point will occur at a higher discharge. O The operating point will occur at a lower discharge.
Find the loss in total pressure for each run in the simple duct system of Fig. 1, using the equal-friction method and in English unit. The total pressure available for the duct system is 0.12 in. wg (30 Pa), and the loss in total pressure for each diffuser at the specified flow rate is 0.02 in. wg (5 Pa). Duct fittings are listed in Table 1. Assume the duct dimeter in run 1 is 10 in. and the rest are 8 in. Does the duct system require any adjustment? 150 cfm e. a 15 ft Plenum е 15 ft 5 ft 5 ft a 3. 20 ft 4 10 ft 200 cfm e 10 ft 150 cfm b Duct Fittings for Figure 1 Fittings Type Abrupt Entrance 90 deg Elbow, Pleated Round to Rectangular boot, Straight 45 deg. Converging Wye 45 deg Elbow, Pleated a d e
2. A centrifugal pump installation has been designed to discharge 0.126 ?3/? of brine (sp.gr. = 1.2). The suction pipe is 305 mm and is at the same level as the discharge pipe which is 203 mm in diameter. At the centerline of suction flange, the vacuum is 154.2 mm Hg. The discharge pressure gauge reads 0.1379 MPa and is connected 1.22 m above the discharge flange centerline. The pump is driven by a 35 KW electric motor that will not carry overload and has an efficiency of 82%. There is no significant head loss. The design conditions have changed, and is now desired to increase the capacity of the pump by increasing the speed. The motor is so designed that its speed maybe increased but its power cannot exceed its design rating. Assuming the pump efficiency to remain constant, how much can the pump capacity be increased without overloading the motor?
A pump has a specific speed of 45 and 600rpm when it delivers 0.01m3/s. Find the head developed by the pump in ft. Ans. 926.07
. The type of flow in a tapering pipe or nozzle with constant velocity at the inletA. Steady Non-uniform C. Steady Uniform B. Unsteady Non-uniform D. Unsteady Uniform
Diffrentiate between pumps and turbines
1) Discuss the difference in the velocities of the model and main pipe.
What is the minimum duct size needed to move 200 cu ft per minute andmaintain duct velocity below 800 feet per minute?
Derive the equation of finding volume flow rate for both Flow nozzle & Venturi meter
. What horsepower is supplied to air moving at 7m/min through a 70cmx90cm duct under a pressure of8cm of H2O?