A Gould Brand, German made Single Reciprocating Compressor has a speed of 1200 rpm. The diameter of the cylinder bore is equal to 120mm and a displacement length of stroke equal to 150mm, at suction pressure of 120KPa with 20 degree centigrade to 215 degree centigrade temperatures. Calculate the following: a. Mass Flow rate, kg/sec b. Pressure Ratio c. Indicated Power d. Shaft Power if Mech'l Eff.=80%

A Gould Brand, German made Single Reciprocating Compressor has a speed of 1200 rpm. The diameter of the cylinder bore is equal to 120mm and a displacement length of stroke equal to 150mm, at suction pressure of 120KPa with 20 degree centigrade to 215 degree centigrade temperatures. Calculate the following: a. Mass Flow rate, kg/sec b. Pressure Ratio c. Indicated Power d. Shaft Power if Mech'l Eff.=80%

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter26: Applications Of Refrigeration Systems

Section: Chapter Questions

Problem 9RQ: Three disadvantages of parallel compressor systems are _____, _____, and ____.

See similar textbooks

Similar questions

Please solve Sub parts A,B,C im needed max in 60 minutes thank u, im very needed the solve 1) Air enters the compressor from a Brayton cycle at a pressure of 100 kPa, temperature27oC and a volumetric flow rate of 1A m3/s. If the turbine inlet temperature is 11ACoC and the ratiopressure (B, 1A)*. If the Compressor Efficiency is 8A% and the turbine efficiency is 9B%. Define : A. From the simulation results, show the p-v or T-s diagram of each case study on B. Complete Compressor Power (kW), Turbine Power (kW), Net Work (kW), Heat In(kW), Net Heat (kW), Back work ratio, Thermal Efficiency (% No Description Pressure ratio=B Ratiopressure=1A 1 Compressor Work (kW) 2 Turbine Work (kW) 3 Net Work (kW) 4 Heat In (kW) 5 Net Heat (kW) 6 Back Work ratio 7 Thermal Efficiency (%) Attach below is the data from the cyclepad simulation in the form of a cycleproperties (if no answer…
a) Calculate the interstage pressure ratio per stage for a two-stage compressor if the overall pressure ratio is 10. b) What speed should a single acting, reciprocating compressor run at to produce 50 m³/h of air? The data for the compressor is: Piston diameter = 100 mm, Stroke length = 110 mm,
Air is at temperature of (290 K) flows in a centrifugal compressor running at (20000 rpm). The other data are given as - isentropic efficiency is (0.80), outer diameter of blasé tip is (600 mm), slip factor is (0.80) Calculate: (i) The temperature rise of air passing through the compressor. (ii) The static pressure ratio Assume absolute velocity of air at inlet and outlet of compressor are the same. Take for air Cp = 1.005 kJ/kg-K, y = 1.4.
1. define the cutfof ratio and the compression ratio 2. air is compressed at a constant temperature find the word done on the fluid under the: - initial pressure 200 kpa - final pressure 1500 kpa - compression temperarture 600 k
A compressor must operate in a speed range between 0 and 1500 rpm. The friction torque of Coulomb Tc is 10 N. m. What should be the required Tw working torque if the compressor constant is 0.5 N. m. s. What is the power required by the engine that operates this compressor?
3.11) The conditions of air at the entry of an axial compressor stage are: Рi %3D 768 тт Hg & Ti = 314 K. The air angles are B1 = 51°, B2 = 9°, a1 = az = 7°. The mean diameter 50 ст. The peripheral speed 100 m/s. Mass-flow rate 25 kg/s work done factor 0.95 mechanical efficiency 92 % stage efficiency 88 % (a) Air angle at the stator entry, [a2 50.18°] (b) Blade height at entry and the hub-tip diameter ratio, [h, = 19 cm ; dn/d = 0.449] (c) Stage loading coefficient. [V = 0.754] (d) Stage pressure ratio. [Po3/Po1 1.075] (e) The power required to drive the stage. [Power = 204.75 kW]
derive the general formula for the intercooling related to the number of stage of compressor
A diesel engine working with cylinder bore of 25 cm and stroke length of 200 mm. the clearance gap beteen TDC and cylinder head is measured as 10 mm. then the compression ratio of the engine will be O b. 22 Oc.21 O d. 200
Derive an eepression for Gysosopic Gouple
Q2. A four-stroke cycle SI engine with 8 cylinder has 6.2-liters. It designed to have a maximum mass flow rate of 0.349 kg/sec. The engine is equipped with a four-barrel carburetor, each barrel having a discharge coefficient of CD = 0.95. The tube discharge coefficient CDc= 0.85 and the capillary tube height differential is Icm. The fuel used is gasoline at FA = 1:15 ,density of gasoline is 750 kg/m'. Calculate the Fuel capillary tube diamețer needed for each venturi throat. %3D
A power generator with two-cylinder, four-stroke gas engine has a bore of480 mm and a stroke of 585 mm. At 300 rev/min the torque developed is10 kNm. The generator is supplied with a mixture of gas and air in theproportion of 1 to 8 by volume. The estimated volumetric efficiency is 80% and the net calorific values of the fuel is 48.6 MJ/m3. Calculate: 1. the swept volume in m3/min, 2. the volume of mixture induced in m3/min 3. the gas flow to engine m3/min4. the energy supplied by gas5. the brake thermal efficiency
what is the types of industrial compressors, write summary and work mehod of each type?