Solve it correctly please. I Water Py = 15.3083psia, Pe3206.2psia is pumped through a linear characteristic valve with a differential pressure of APupstream side of the valve is Pı = 200psia and the nominal flow rate through the valve at a quarter of the valve being open is 125gpm. Would this valve50 The pressure at theever experience choked flow?

Given data: Pv=15.3083 psiaPc=3206.2 psia∆P=50P1=200 psiaQ=125 gpm Need to check will the valve…

Water P, = 15.3083psia, P. = 3206.2psia is pumped through a linear characteristic valve with a differential pressure of AP upstream side of the valve is P = 200psia and the nominal flow rate through the valve at a quarter of the valve being open is 125gpm. Would this valve ever experience choked flow? 50 The pressure at the

Water P, = 15.3083psia, P. = 3206.2psia is pumped through a linear characteristic valve with a differential pressure of AP upstream side of the valve is P = 200psia and the nominal flow rate through the valve at a quarter of the valve being open is 125gpm. Would this valve ever experience choked flow? 50 The pressure at the

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

How to work out a Bernoulli pipe diameter change to increase or decrease flow into a Ram pump drive pipe. The ram pump selected is a: RAM PO400 with a 80mm drive pipe, will deliver 19200 liters per day to 125m The elevation of ram pump is 334m The elevation of drive inlet pipe is 359m The height being pumped to is 111m
Find the loss in total pressure for each run in the simple duct system of Fig. 1, using the equal-friction method and in English unit. The total pressure available for the duct system is 0.12 in. wg (30 Pa), and the loss in total pressure for each diffuser at the specified flow rate is 0.02 in. wg (5 Pa). Duct fittings are listed in Table 1. Assume the duct dimeter in run 1 is 10 in. and the rest are 8 in. Does the duct system require any adjustment? 150 cfm e. a 15 ft Plenum е 15 ft 5 ft 5 ft a 3. 20 ft 4 10 ft 200 cfm e 10 ft 150 cfm b Duct Fittings for Figure 1 Fittings Type Abrupt Entrance 90 deg Elbow, Pleated Round to Rectangular boot, Straight 45 deg. Converging Wye 45 deg Elbow, Pleated a d e
A compressor piston has a stroke of 380 mm and the clearance volume of 7% of thestroke volume. At the beginning of compression stroke the pressure of air is 0.99 barWhen the piston has travelled 260 m from the begining of the compression stroke thedelivery valves open and delivers air at 4 bar. Find the value of "n", iif the compressionfollows the law PVn = CA. 1.37B. 1.39C. 1.28D. 126
Water is to be pumped to an atmospheric rooftop storage tank atop a 5-story building, 75 feet above ground-level. A pump station is located at the ground-level. The suction line is a 2-inch ID commercial steel pipe tapped into a municipal supply line maintained at 50 PSIG 5 feet below ground-level. The discharge line is 1.5-inch ID commercial steel, and the total length of pipe is approximately 100 ft. There are two ball valves, a water meter, and gate valve on the discharge line. Determine the pump head required to deliver 40 GPM and the pump power that must be supplied to the water. If a pump is required, what is the motor power required if the pump operates at 55% efficiency?
s) The FD fan delivered the air at the static pressure (350 kPa) with dynamic pressure (150 kPa). The airflow is (368 m³ /min). The fan shat power is (6000 hp). Calculate: 1- Static efficiency. 2- Fan power input. 3- Mechanical efficiency. Pr-Pz
A single-stage centrifugal pump having a suction pipe 254 mm in diameter anda discharge pipe diameter of 5 inches is being tested and found out to discharge 48 lps ofwater. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and adischarge gage reads 150 kPa at a distance 100 cm above the point where the inletpressure was measured. If the kW rating of the driving motor is 12 kW, calculate a) thepump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate,head, and power developed if the pump speed was increased to 3600 rpm? Assumeconstant efficiency. c) Determine the pump type.
A pitot-static tube is used to measure the velocity of water in a pipe. The stagnation pressure head is 6 m and static pressure head is 5 m. Calculate the velocity of flow assuming the co- efficient of tube equal to 0.98.
A supply water is available at a head of 684 meters. It is proposed to build a turbine to operate at 6 rev/s and develops 14.92 MW.Compute the specific speed in rpm.a. 3297rpmb. 4356rpmc. 6568rpmd. 3477rpm
Centimuity oquation ofastendy frow. Terriellis problemfontflow of liquid througha hole) Problem:Detemine the absolute pressure at the inlet section of the pump. Flow rate of the pump Q=2,3 1/sec, l=1,5 m, d=40 mm, t=60°C. Static pressure in the tank p.=266,8 mmHg. Wedge resistance coefficient Sw=1,5, pipe inlet resistance coefficient Çin=0,5, the height of the oil level in the tank above the pump inlet section н-1,2 м, оil 1-12. H кран насос
A "spa tub" is to be designed to replace bath tubs in reno- vations. There are to be 6 outlet nozzles, each with a di- ameter of 12 mm, and each should have an outlet velocity of 12 m/s. What is the required flow rate from the single pump that supplies all of these nozzles? If there is one suction line leading to the pump, what is the minimum diameter to limit the velocity at the inlet of the pump to 2.5 m/s?
a pump operating at 1750 rpm delivering 600 gpm against total head of 200 tt. changes in the piping system have increase the total head of 450 tt. At what RPM should the pump be operated to achieve thus new head at the same efficiency?
As shown in the picture blew, a pump can deliver volume flow rate of of water through a vertical lift of . The inlet to the pump is just below the water surface and the discharge is to the atmosphere through a DN50 schedule 40 steel pipe. The energy loss . (2) Select the correct simplified general energy equation for point 1 and 2