28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resisto a. If silicon diodes are employed, what is the de voltage available at the load? b. Determine the required PIV rating of each diode. c. Find the maximum current through each diode during conduction. d. What is the required power rating of each diode?

28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resisto a. If silicon diodes are employed, what is the de voltage available at the load? b. Determine the required PIV rating of each diode. c. Find the maximum current through each diode during conduction. d. What is the required power rating of each diode?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
For the rectifier in the figure below, state the conduction sequence of the diodes for periods t1 to tó. D1 D2 D3 22) tl: D. & D.. 23) t2: D. & D.. 24) t3: D. & D.. 25) t4: D. & D.. D4 D5 D6 26) t5: D. &D. 27) t6: D.AN A & D....... Vm cot t6
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
7 Full-Wave Rectification 28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of 1 k2. a. If silicon diodes are employed, what is the de voltage available at the load? b. Determine the required PIV rating of each diode. c. Find the maximum current through each diode during conduction. d. What is the required power rating of each diode?
28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of 1 k. a. If silicon diodes are employed, what is the de voltage available at the load? b. Determine the required PIV rating of each diode. c. Find the maximum current through each diode during conduction. d. What is the required power rating of each diode?
A three-phase half wave rectifier has a supply of 150V/phase. Determine the mean load voltage and the required diode rating, assuming the load current is level at 25A. Assume each diode has a volt-drop of 0.7V.
Consider the circuit shown in Figure 2. The cut-in voltage of each diode is . Let and assume both diodes are conducting. Determine if this is a valid assumption and explain your answer. And calculate the values of IR, ID, Ip2, and V.. Rj =1.7 kQ ww VB =1 V D1 Dz R2D 4 kQ Figure 2
For the circuit shown below, compute the maximum current through each resistor when terminal A is a) positive and, b) negative. Assume the diodes are ideal.
A full-wave bridge rectifier with a 100V rms sinusoidal input has a load resistor of 1 k. a. If silicon diodes are employed, what is the de voltage available at the load? b. Determine the required PIV rating of each diode. c. Find the maximum current through each diode during conduction. D.
In a full wave rectifier circuit involving double diodes, a sinusoidal input signal of the following nature is applied e=10 sin(500*pi*t) V. What will be value of the dc voltage obtained at the output of the rectifier.
Q-2: The input signal for half-wave rectifier is a.c. signal. The output of 800 load resistor is 50V d.c. voltage. The diode has a resistance of 25 Q. 5 a) Draw the graphs of input signal, diode signal and output signals. 20 b) Calculate the maximum voltage value for the input signal. AC Supply Diode www
Given the half-wave rectifier circuit shown 220V 60Hz 220V:Es Es D RL The load resistor is 2292 and it dissipates 2W. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average diode current and PIV of the diode.