Introductory Circuit Analysis (13th Edition)
13th Edition
ISBN: 9780133923605
Author: Robert L. Boylestad
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Question
(1) Sketch the circuit for an ac supply input to a full-wave diode rectifier with a resistive load and no smoothing capacitor.
(2).Sketch the ac supply voltage and the voltage across the resistive load in (question no 1)indicating the period of the resistive load voltage.
(3) For the circuit in (question no 1) calculate the average and rms voltages across the resistive load for an rms ac supply voltage of 115 V assuming no diode voltage.
Expert Solution
This question has been solved!
Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.
Step by stepSolved in 2 steps with 2 images
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A Full-wave bridge rectifier Circuit contains 4 Germanium diodes Cuse the Constant voltage drop model with VD = 0.30) driving ac a Load resistance of 10 kur. An Source with a Peak value of 4ou at bottz Vortage Source with a applied to the Circuit. a DIS 2 Determine the de value of the output wave form Determine the value of the Capacitor In uf needed to limit the output ripple vortage to 0.5 V if the Peak output voltage is equal to Upic -2VDarrow_forwardExercises: 1. A full-wave bridge rectifier isolated from the 220 V rms power line by a transformer. Assuming the diode voltage drops are 0.7 V. i. What turns ratio should the transformer have in order to produce an average current of 1A in a 10 load? ii. What is the average current in each diode under the conditions of (i)? iii. What minimum PIV rating should each diode have? iv. How much power is dissipated by each diode? 2. A full-wave bridge rectifier is operated from a 50 Hz, 220 V rms line. It has a 100 μF filter capacitor and a 2 k 2 load. Neglect diode voltage drops. i. What is the percent ripple? ii. What is the average current in the load?arrow_forwardOBJECTIVES :1. To be able to construct a half-wave rectifier circuit and examine its inputand output waveforms.2. To find out the phase relation between the voltage across the load and thevoltage across the diode. QUESTIONS :1. What is the effect of reversing the diode in the circuit (Step 7)?2. Compare the waveform across the diode (Step 9) with the waveformacross the load (Step 6) ? 3. What portion of the input signal is clipped at the output ?4. Give the advantages of a silicon over germanium rectifier diode.arrow_forward
- A semiconductor diode having ideal forward and reverse characteristics is used in a half-wave rectifier circuit supplying a resistive load of 500 ohm. If the r.m.s. value of the sinusoidal supply voltage is 230 V, determine (i) the r.m.s. diode current and (ii) power dissipated in the load.arrow_forward04: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10°t)] rms input signal has a loud resistor of 3.3k0. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VLp) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ? 4. What is the de valtage available at the load? 5. Explain who could filtering output signal. 6. Draw circuit that give opposite out waveform. 7. Why connect circuit in this form.arrow_forwardConsider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new grapharrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSONDelmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningProgrammable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
- Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill EducationElectric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSONEngineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:PEARSON
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning
Programmable Logic Controllers
Electrical Engineering
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education
Fundamentals of Electric Circuits
Electrical Engineering
ISBN:9780078028229
Author:Charles K Alexander, Matthew Sadiku
Publisher:McGraw-Hill Education
Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:9780134746968
Author:James W. Nilsson, Susan Riedel
Publisher:PEARSON
Engineering Electromagnetics
Electrical Engineering
ISBN:9780078028151
Author:Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:Mcgraw-hill Education,