A filtered 4 diode full wave rectifier circuit withthe following specifications:The line load is 240 V rms with a frequency of50 Hz, transformer ratio 199:20, with filtera 470 µF capacitor, and a 10KQ chargeresistor. So:a. What is the transformer ratio if we want theripple charge to be 0.3 V?b. If one of the diodes in the circuit is short,what are the possibilities?

The given information about a 4 diode based full wave rectifier with filter capacitor is, Supply…

A filtered 4 diode full wave rectifier circuit with the following specifications: The line load is 240 V rms with a frequency of 50 Hz, transformer ratio 199:20, with filter a 470 µF capacitor, and a 10 kO charge resistor. So: a. What is the transformer ratio if we want the ripple charge to be 0.3 V? b. If one of the diodes in the circuit is short, what are the possibilities?

A filtered 4 diode full wave rectifier circuit with the following specifications: The line load is 240 V rms with a frequency of 50 Hz, transformer ratio 199:20, with filter a 470 µF capacitor, and a 10 kO charge resistor. So: a. What is the transformer ratio if we want the ripple charge to be 0.3 V? b. If one of the diodes in the circuit is short, what are the possibilities?

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
A full-wave rectifier uses 2 diodes. The internal resistance of each diode is 20 Q. The transformer RMS secondary voltage from centre tap to each end of the secondary is 50 V and the load resistance is 980 Q. Mean load current will be
A full wave bridge rectifier is supplied from 230V, 50Hz and uses a transformer of turns ration 15:1. It uses load resistance of 50 ohms. Calculate load voltage and ripple voltage. Assume ideal diode and transformer. Assume ripple factor equals to 0.482. a.Load Voltage= 13.8 V; Ripple Voltage=6.652 V b.Load Voltage= 15.6 V; Ripple Voltage=7.611 V c.Load Voltage= 21.3 V; Ripple Voltage=8.410 V d.Load Voltage= 25.1 V; Ripple Voltage=10.442 V
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
Problem # 4 In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VpC e. PIV (Peak Inverse Voltage) 10:1 Dy 1ISV ms Ouiput RL 2.2 k2 D, 50 pF All diodes are IN4001. alleee
the three phase half wave uncontrolled rectifier is operated from 500v,50Hz supply at secondary side and the load resistance is 25 ohms. if the source inductance is negligible, determine a) rectification efficiency b) form factor c) ripple factor d) transformer utilization factor e) peak inverse voltage of each diode
1) How is the diode and zener diode in the electronic circuit and how they work?indicate the differences between them.2) Can a zener diode be used instead of a regular diode? please explain.3) Is it to step down and rectify the 220V AC signal by means of a transformer or to convert 220 V?rectify it and then reduce its value to the desired DC level using a voltage divider circuit?suitable.?4) Bridge type full wave rectification with two diodes full wave rectification using a medium ended transformerCompare the rectifier circuit and list its advantages and disadvantages relative to each other.5) What is the concept of PIV (Peak Inverse Voltage) for rectifier circuits?For which rectifier circuits is this value more important?
14. A thyristor that looks like two back-to-back 4 layer diodes is the a. SCR b. Triac c. SCS d. DIAC 15. A device that has an unstable negative resistance region is the a. UJT b. SCS c. TRIAC d. DIAC
For the rectifier in the figure below, state the conduction sequence of the diodes for periods t1 to tó. D1 D2 D3 22) tl: D. & D.. 23) t2: D. & D.. 24) t3: D. & D.. 25) t4: D. & D.. D4 D5 D6 26) t5: D. &D. 27) t6: D.AN A & D....... Vm cot t6
In a full wave rectifier circuit involving double diodes, a sinusoidal input signal of the following nature is applied e=10 sin(500*pi*t) V. What will be value of the dc voltage obtained at the output of the rectifier.