Q2.A three phase full wave uncontrolled bridge rectifier has an AC input voltage of 90 V RMS at 60 Hz anda resistive load of 4400.a. What is the average output voltage?b.What is the average output current?c. What should be the voltage blocking capability of the diodes?

Given data, Supply RMS voltage Vr=90 V. Frequency f=60 Hz. Load resistance RL=440 Ω.

Q2. A three phase full wave uncontrolled bridge rectifier has an AC input voltage of 90 V RMS at 60 Hz and a resistive load of 44002. a. What is the average output voltage? b. What is the average output current? c. What should be the voltage blocking capability of the diodes?

Q2. A three phase full wave uncontrolled bridge rectifier has an AC input voltage of 90 V RMS at 60 Hz and a resistive load of 44002. a. What is the average output voltage? b. What is the average output current? c. What should be the voltage blocking capability of the diodes?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1)Define Drift and Diffusion current in Semiconductor. 2. Why n - type impurities are called as Donor impurities? 3. Give the other names of depletion region? (At least Two) 4. General Purpose Diodes are mostly preferred in chopper circuits. Is it True? Justify.
Discussion: 1. Discuss the obtained curves. 2. What are the advantages of using cascade voltage regulator circuit? 3. To stabilize a voltage of 65 V, one can: a. Use one 65V zener diode b. Use ten 6.5 V zener diodes in series If the costs are irrelevant, then which solution is best and why?
9. The diodes in a bridge rectifier each have a maximum dc current rating of 2 A. What is the maximum value of the dc load current? 10. What is the PIV across each diode of a bridge rectifier with a secondary voltage of 20 V,rms?
A tunnel diode is used: A)in very fast-switching circuits. B) in circuits requiring negative resistance. C) in high-power circuits. D) in power supply rectifiers.
1. Draw and briefly explain the ideal characteristics of PN-junction diode ? 2. Explain briefly about avalanche and Zener breakdown ? 3. In which region can Zener diode be used as a regulator? Why? 4. What is the ripple factor? For a good filter, should the ripple factor be high or low? 5. What is a rectifier? What is the difference between a full-wave rectifier and a half-wave rectifier?
Draw the circuit diagram of a clipper that will produce an output waveform below. From the output waveform Voltage A is 6.7 and Voltage B is -9.7 .Input peak-to-peak voltage is given as 20 volts. Assume Silicon diodes are used. 1. For the positive half cycle, the needed battery voltage is........ 2. For the negative half cycle, the needed battery voltage is........
What will be the out put of the D'Arsonval meters, if an average responding a.c meter of half-wave rectifier read (236 v), and true form foctor of input waveform is (114). *
In a full wave bridge rectifier, the transformer secondary voltage is 20sinwt. The forward resistance of each diode is 252 and load resistance is 1.5KN. Calculate, i. Im ii. Idc iii. Pdc iv. Pac V.
b. Calculate the following about the circuit in the figure (If silicon diodes are employed in the rectification);i. the peak value of the output voltage considering the drop across each diode, Vpk.ii. the average voltage, Vdc. iii. The current through the load resistor, IL.iv. The current diode, Id.v. The frequency of the output signal, Fout.vi. Calculate the efficiency of the full wave rectifier expressed in percentage. vii. Sketch a graph of the input and output voltage against time.
Q4/: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10³t)] rms input signal has a load resistor of 3.3k2. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VL-P) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ? 4. What is the de voltage available at the load? 5. Explain who could filtering output signal. 6. Draw circuit that give opposite out waveform. 7. Why connect circuit in this form.
A full-wave bridge rectifier with a 100V rms sinusoidal input has a load resistor of 1 k. a. If silicon diodes are employed, what is the de voltage available at the load? b. Determine the required PIV rating of each diode. c. Find the maximum current through each diode during conduction. D.
04: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10°t)] rms input signal has a loud resistor of 3.3k0. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VLp) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ? 4. What is the de valtage available at the load? 5. Explain who could filtering output signal. 6. Draw circuit that give opposite out waveform. 7. Why connect circuit in this form.