a) Explanation Draw the given Air standard cycle on P − v and T-s diagram as in Figure (1). b) To determine The total heat input per unit mass. c) To determine The thermal efficiency of the given Air standard cycle

8th Edition

ISBN: 9780073398174

Author: Yunus A. Cengel Dr., Michael A. Boles

Publisher: McGraw-Hill Education

See similar textbooks

Concept explainers

IC engines

The term "engine" indicates a mechanical device/machine used to convert input energy to a specific mechanical output. The input energy may be in the form of chemical energy, thermal energy, or so on and mechanical output is in the form of mechanical ener…

Question

Chapter 9.12, Problem 16P

To determine

The sketch of the P−ν and T-s diagrams for the given cycle.

To determine

The total heat input per unit mass.

To determine

The thermal efficiency of the given Air standard cycle

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 9.12, Problem 15P

Chapter 9.12, Problem 17P

Students have asked these similar questions

Q Derive (continuity equation)? I want to derive clear mathematics.

motor supplies 200 kW at 6 Hz to flange A of the shaft shown in Figure. Gear B transfers 125 W of power to operating machinery in the factory, and the remaining power in the shaft is mansferred by gear D. Shafts (1) and (2) are solid aluminum (G = 28 GPa) shafts that have the same diameter and an allowable shear stress of t= 40 MPa. Shaft (3) is a solid steel (G = 80 GPa) shaft with an allowable shear stress of t = 55 MPa. Determine: a) the minimum permissible diameter for aluminum shafts (1) and (2) b) the minimum permissible diameter for steel shaft (3). c) the rotation angle of gear D with respect to flange A if the shafts have the minimum permissible diameters as determined in (a) and (b).

First monthly exam Gas dynamics Third stage Q1/Water at 15° C flow through a 300 mm diameter riveted steel pipe, E-3 mm with a head loss of 6 m in 300 m length. Determine the flow rate in pipe. Use moody chart. Q2/ Assume a car's exhaust system can be approximated as 14 ft long and 0.125 ft-diameter cast-iron pipe ( = 0.00085 ft) with the equivalent of (6) regular 90° flanged elbows (KL = 0.3) and a muffler. The muffler acts as a resistor with a loss coefficient of KL= 8.5. Determine the pressure at the beginning of the exhaust system (pl) if the flowrate is 0.10 cfs, and the exhaust has the same properties as air.(p = 1.74 × 10-3 slug/ft³, u= 4.7 x 10-7 lb.s/ft²) Use moody chart (1) MIDAS Kel=0.3 Q3/Liquid ammonia at -20°C is flowing through a 30 m long section of a 5 mm diameter copper tube(e = 1.5 × 10-6 m) at a rate of 0.15 kg/s. Determine the pressure drop and the head losses. .μ= 2.36 × 10-4 kg/m.s)p = 665.1 kg/m³

Chapter 9 Solutions

Thermodynamics: An Engineering Approach

Ch. 9.12 - What are the air-standard assumptions?Ch. 9.12 - What is the difference between air-standard...Ch. 9.12 - How does the thermal efficiency of an ideal cycle,...Ch. 9.12 - What does the area enclosed by the cycle represent...Ch. 9.12 - Prob. 5P Ch. 9.12 - Prob. 6P Ch. 9.12 - Can the mean effective pressure of an automobile...Ch. 9.12 - Prob. 8P Ch. 9.12 - What is the difference between spark-ignition and...Ch. 9.12 - Prob. 10P

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The sketch of the P − ν and T-s diagrams for the given cycle.

Concept explainers

The sketch of the P−ν and T-s diagrams for the given cycle.

The total heat input per unit mass.

The thermal efficiency of the given Air standard cycle

Want to see the full answer?

Chapter 9 Solutions