OPERATIONS MANAGEMENT IN THE SUPPLY CHAIN: DECISIONS & CASES (Mcgraw-hill Series Operations and Decision Sciences)
7th Edition
ISBN: 9780077835439
Author: Roger G Schroeder, M. Johnny Rungtusanatham, Susan Meyer Goldstein
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 9, Problem 4P
a)
Summary Introduction
To determine: The UCL and LCL for a
b)
Summary Introduction
To determine: The UCL and LCLs for a sample size of 10,000.
c)
Summary Introduction
To determine: The sample size that should be recommended.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
An X-bar chart has the following control limits UCL=251.5 and LCL=248.5. The sample size is n=4,
the process mean is equal to 250 and the process standard deviation is sigma = 1.0. What is the Cp
value ?
0.500
not enough information
0.316
0.408
0.447
0.353
A process sampled 20 times with a sample of size 8 resulted in = 28.5 and R = 1.8. Compute the upper and lower control limits for the x chart for this process. (Round your answers to two decimal places.)
UCL = 29.17
LCL = 27.82
X
Compute the upper and lower control limits for the R chart for this process. (Round your answers to two decimal places.)
UCL = 3.35
X
LCL =
0.24
6.
The defect rate for your product has historically been about
4.50%.
For a sample size of
500,
the upper and lower
3-sigma
control chart limits are:
Part 2
UCLp
= _______ (enter your response as a number between 0 and 1, rounded to four decimal places).
The Standard deviation of defect rate of product is given __________.
The Upper and Lower 3-sigma control charts limits are:
UCLp ________
LCLp ________
Chapter 9 Solutions
OPERATIONS MANAGEMENT IN THE SUPPLY CHAIN: DECISIONS & CASES (Mcgraw-hill Series Operations and Decision Sciences)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, operations-management and related others by exploring similar questions and additional content below.Similar questions
- A can filling process at a beverage manufacturing factory is assumed to be in control with limits of 84 ±3 had sample averages for the x-bar chart of the following:87.1,87, 87.2, 89, 90, 88.5, 89.5, and 88. Which of the following statement ?below are correct Not enough information to determine .a O None is correct b O Process mean is in-control .c O Process mean is out-of-control .d O أخل اختياري 4) E ENG acerarrow_forwardAuto pistons at Wemming Chung's plant in Shanghai are produced in a forging process, and the diameter is a critical factor that must be controlled. From sample sizes of 10 pistons produced each day, the mean and the range of this diameter have been as follows: a) What is the value of x? = x= 155.56 mm (round your response to two decimal places). b) What is the value of R? R 4.48 mm (round your response to two decimal places). c) What are the UCL; and LCL; using 3-sigma? Day 1 2 3 4 5 Upper Control Limit (UCL) = 156.94 mm (round your response to two decimal places). Lower Control Limit (LCL-) = 154.18 mm (round your response to two decimal places). d) What are the UCLR and LCLR using 3-sigma? Upper Control Limit (UCL) = 7.96 mm (round your response to two decimal places). Mean x (mm) 154.9 153.2 155.6 155.5 158.6 Range R (mm) 4.0 4.8 3.9 5.0 4.7 Lower Control Limit (LCL) = 1.00 mm (round your response to two decimal places). e) If the true diameter mean should be 155 mm and you want…arrow_forwardE1 You manufacture a widget and use a C chart to monitor the number of defects associated with your process. Your sample size is constant and on average you find7 defects per sample. Identify the upper and lower control limits for the C chart.arrow_forward
- Specifications for a part for a 3-D printer state that the part should weigh between 24 and25 ounces. The process that produces the parts has a mean of 24.5 ounces and a standard deviation of .2 ounce. The distribution of output is normal. What percentage of parts will not meet the weight specs? Within what values will 95.44 percent of the sample means of this process fall if samples of n = 16 are taken and the process is in control (random)? Using the control limits from part b, would the following sample means be in control? 24.52, 24.53, 24.44, 24.51, 24.41, 24.39 An automatic filling machine is used to fill 1-liter bottles of cola. The machine’s output is approxi- mately normal with a mean of 1.0 liter and a standard deviation of .01 liter. Output is monitored using means of samples of 25 observations. Determine upper and lower control limits that will include roughly 97 percent of the sample means when the process is in control. Given the following sample means—1.005,…arrow_forward2. x and R charts with n = 4 are used to monitor a normally distributed quality characteristic. The control chart parameters are x Chart R Chart UCL = 815 UCL = 46.98 %3D Center line = 800 Center line = 20.59 LCL = 785 LCL = 0 Both charts exhibit control. What is the probability that a shift in the process mean to 790 will be detected on the first sample following the shift? Please show all your work for full credit.arrow_forwardA process that is in control has a mean of 13 and a standard deviation of .7. a. Construct an x control chart if samples of size 3 are to be used (to 1 decimal). Repeat part (a) for samples of size 8 and 13 (to 2 decimals).arrow_forward
- The overall average on a process you are attempting to monitor is 60.0 units. The process population standard deviation is 1.72. Sample size is given to be 4. Part 2 a) Determine the 3-sigma x-chart control limits. Upper Control Limit (UCLx)=enter your response here units (round your response to two decimal places). Part 3 Lower Control Limit (LCLx)=enter your response here units (round your response to two decimal places). Part 4 b) Now determine the 2-sigma x-chart control limits. Upper Control Limit (UCLx)=enter your response here units (round your response to two decimal places). Part 5 Lower Control Limit (LCLx)=enter your response here units (round your response to two decimal places). Part 6 How do the control limits change? A. The control limits are tighter for the 3-sigma x-chart than for the 2-sigma x-chart. B. The control limits for the 2-sigma x-chart and for the 3-sigma x-chart are the same. C. The control limits…arrow_forwardTwenty samples of 100 items each were inspected when a process was considered to be operating satisfactorily. In the 20 samples, a total of 140 items were found to be defective. (a) What is an estimate of the proportion defective when the process is in control? (b) What is the standard error of the proportion if samples of size 100 will be used for statistical process control? (Round your answer to four decimal places.) (c) Compute the upper and lower control limits for the control chart. (Round your answers to four decimal places.) UCL = LCL =arrow_forwardUsing samples of 200 credit card statements, an auditor found the following: Sample 1 2 3 4 Number with errors 4 2 5 9 a. Determine the fraction defective in each sample. b. If the true fraction defective for this process is unknown, what is your estimate of it? c. What is your estimate of the mean and standard deviation of the sampling distribution of fractions defective for samples of this size? d. What control limits would give an alpha risk of .03 for this process? Page 457 e. What alpha risk would control limits of .047 and .003 provide? f. Using control limits of .047 and .003, is the process in control? g. Suppose that the long-term fraction defective of the process is known to be 2 percent. What are the values of the mean and standard deviation of the sampling distribution? h. Construct a control chart for the process, assuming a fraction defective of 2 percent, using two-sigma control limits. Is the process in control? Can you show me the steps and formulas using excelarrow_forward
- Use the data in the Excel file (#1 Data). These data represent seven samples (taken on seven sequential days) each containing eight bags of salt. The weights (in ounces) are shown. Create an X-bar chart and an R-chart for the data provided. Comment on whether each chart indicates the process is in control or not. Sample Observation 1 2 3 4 5 6 7 1 61.20 62.00 60.50 61.20 61.40 59.20 62.10 2 61.00 61.40 63.40 61.00 62.30 61.00 63.00 3 60.80 60.20 60.80 60.80 60.20 60.80 60.20 4 59.10 61.30 58.70 62.10 61.30 60.00 61.30 5 61.40 60.60 61.40 61.40 60.60 61.40 59.30 6 61.70 60.30 62.10 61.70 59.80 62.10 60.30 7 62.40 61.30 62.40 62.40 61.30 62.40 61.30 8 61.10 60.20 60.90 62.30 60.20 60.20 60.50arrow_forwardA company is evaluating its manufacturing system to produce steel rods for a new customer. Fif- teen samples, cach containing five steel rods, were taken from the process. The length of each rod in the samples was measured and is shown in the following table: Sample Rod 1 10.001 Rod 2 Rod 3 Rod 4 Rod 5 1 10.009 9.999 10.001 9.992 10.002 10.013 9.992 10.001 10.002 9.999 9.997 3 9.993 10.012 9.999 9.989 10.011 4 9.989 10,001 9.998 5 10.001 10.002 9.999 9.995 10.003 9.993 6. 9.995 10.003 10.002 10.001 7. 9.999 9.998 10.002 9.997 9.993 10.008 8. 10.002 10.001 9.999 10.001 9 10.021 10.008 9.992 9.989 9.996 10 10.001 10.010 10.002 10.003 10.006 11 10.002 10.008 9.992 9.999 10.001 12 9.992 9.996 9.999 10.005 9.989 13 10.001 10.009 10.001 9.992 10.002 14 10.003 9.991 10.002 9.999 10.003 15 9.998 10.002 9.991 10.003 10.001arrow_forwardAnswer the given question with a proper explanation and step-by-step solution. Johnson & Johnson manufactures needles that are subjected to a bend test. They use statistical process control (SPC) and the results (measured in grams) are plotted on a chart. If the process average is 26,1 and the average range is 5; what will the control limits be if the sample size n=8? The factor for calculation of control limits is 0,373 for sample size n=8. Which statement(s) is/are true? a The process is "out of control". b The process is "in control". c The upper control limit equals 27,965. d The upper control limit equals 24,235. e The lower control limit equals 27,965. 1. a 2. b, c 3. a, c 4. b, c, d 5. a, d, earrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Practical Management ScienceOperations ManagementISBN:9781337406659Author:WINSTON, Wayne L.Publisher:Cengage,
Operations ManagementOperations ManagementISBN:9781259667473Author:William J StevensonPublisher:McGraw-Hill Education
Operations and Supply Chain Management (Mcgraw-hi...Operations ManagementISBN:9781259666100Author:F. Robert Jacobs, Richard B ChasePublisher:McGraw-Hill Education
Purchasing and Supply Chain ManagementOperations ManagementISBN:9781285869681Author:Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. PattersonPublisher:Cengage Learning
Production and Operations Analysis, Seventh Editi...Operations ManagementISBN:9781478623069Author:Steven Nahmias, Tava Lennon OlsenPublisher:Waveland Press, Inc.
Practical Management Science
Operations Management
ISBN:9781337406659
Author:WINSTON, Wayne L.
Publisher:Cengage,
Operations Management
Operations Management
ISBN:9781259667473
Author:William J Stevenson
Publisher:McGraw-Hill Education
Operations and Supply Chain Management (Mcgraw-hi...
Operations Management
ISBN:9781259666100
Author:F. Robert Jacobs, Richard B Chase
Publisher:McGraw-Hill Education
Purchasing and Supply Chain Management
Operations Management
ISBN:9781285869681
Author:Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson
Publisher:Cengage Learning
Production and Operations Analysis, Seventh Editi...
Operations Management
ISBN:9781478623069
Author:Steven Nahmias, Tava Lennon Olsen
Publisher:Waveland Press, Inc.