Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133128741
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 33, Problem 31QLP
To determine
Based on personal experiences, make a list of parts and components that have to be replaced due of wear.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
12. What are the main methods adopted by the designer to predict the rates of wear.
Which three of the following are names given to the three regions in the typical wear growth curve: (Choose three answers)
temperature region
diffusion region
failure region
0000000
accelerated wear region
break-in period
steady-state wear
abrasion region
Estimate the manufacturing cost for a simple machined component: a. Compare the costs for manufacturing volumes of 1, 10, 100, 1000, and 10,000 pieces with an intermediate tolerance and surface finish. Explain why there is a great change between 1 and 10 and a small change between 1000 and 10,000 pieces. b. Compare the costs for fit, intermediate, and rough tolerances with a volume of 100 pieces. c. Compare the costs of manufacturing the component out of various materials.
Chapter 33 Solutions
Manufacturing Engineering & Technology
Ch. 33 - What is tribology?Ch. 33 - Explain what is meant by (a) surface texture and...Ch. 33 - List and explain the types of defects typically...Ch. 33 - Define the terms (a) roughness, and (b) waviness.Ch. 33 - Explain why the results from a profilometer are...Ch. 33 - Prob. 6RQCh. 33 - List the types of wear generally observed in...Ch. 33 - Define the terms wear, friction, and lubricant.Ch. 33 - How can adhesive wear be reduced? Abrasive wear?Ch. 33 - Prob. 10RQ
Ch. 33 - Explain the functions of a lubricant in...Ch. 33 - Prob. 12RQCh. 33 - Prob. 13RQCh. 33 - Describe the factors involved in lubricant...Ch. 33 - Prob. 15RQCh. 33 - Prob. 16QLPCh. 33 - Explain the significance of the fact that the...Ch. 33 - Prob. 18QLPCh. 33 - Explain why identical surface-roughness values do...Ch. 33 - Prob. 20QLPCh. 33 - Prob. 21QLPCh. 33 - Prob. 22QLPCh. 33 - Prob. 23QLPCh. 33 - Comment on the surface roughness of various parts...Ch. 33 - Prob. 25QLPCh. 33 - Do the same as for Problem 33.25, but for surface...Ch. 33 - Describe your observations regarding Fig. 33.7.Ch. 33 - Give the reasons that an originally round specimen...Ch. 33 - Prob. 29QLPCh. 33 - Explain the reason that the abrasive-wear...Ch. 33 - Prob. 31QLPCh. 33 - List the similarities and differences between...Ch. 33 - Explain why the types of wear shown in Fig. 33.11...Ch. 33 - List the requirements of a lubricant.Ch. 33 - List manufacturing operations in which high...Ch. 33 - List manufacturing operations in which high wear...Ch. 33 - Prob. 37QLPCh. 33 - Prob. 38QTPCh. 33 - A surface with a triangular sawtooth roughness...Ch. 33 - List the steps you would follow if you wished to...Ch. 33 - Discuss the tribological differences between...Ch. 33 - Section 33.2 listed major surface defects. How...Ch. 33 - Describe your own thoughts regarding biological...Ch. 33 - Prob. 48SDPCh. 33 - Prob. 49SDPCh. 33 - Prob. 50SDPCh. 33 - Describe your thoughts on the desirability of...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What are codes and standards?arrow_forwardWhat are assessments that measure strength, speed, agility, or high-speed strength? What are the protocols and norms for each?arrow_forwardAs an engineer you are asked to choose 1 component from what you studied ( Screw, rolling bearing, Sliding Bearing, key, or shaft). 1. Explain what you know about that component and its types? 2. Make a sketch of the component with the important dimensions required? 3. Explain in detail what information you need to know to design this component?arrow_forward
- What part provides the most manufacturing tolerance and is easiest to work with, part 1 or part 2? Explain why.arrow_forwardPlease show the complete solution and box the final answer. Thanks! Subject: Mechanical Vibrationarrow_forwardResearch and identify one type of geometric tolerances (besides obvious specs like length, distance, diameter, etc.) that can be called out on a technical drawing. Discuss a specific feature in a specific product/design case where calling out this geometric tolerance would be relevant for performance, assembly, or general operation.arrow_forward
- Describe working and environmental conditions that lead to failure for a product made from material from each of the four material categories.arrow_forwardIf you were manufacturing a component with a minimum thickness of 1mm and a tolerance of 0.1mm (or better) which method may be appropriate to achieve this?arrow_forwardgive examples of non conservative forcearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Hand Tools; Author: UCI Media;https://www.youtube.com/watch?v=4o0tqF0jDdo;License: Standard Youtube License