Principles of Foundation Engineering (MindTap Course List)
8th Edition
ISBN: 9781305081550
Author: Braja M. Das
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 2, Problem 2.21P
To determine
Calculate the shear stress parameters
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
5- The shear strength of a normally consolidated clay can be given by the equation tf o'tan 27°. Following are the
results of a
consolidated-undrained
test on the clay.
• Chamber-confining pressure = 3,130 lb/ft²
Deviator stress at failure = 2,510 lb/ft²
a) Determine the consolidated-undrained friction angle
b) Pore-water pressure developed in the specimen at failure
2- A three-axis compression test on a clay sample
that is comprehensive and normal up to a stress
of 300 kPa and a specific volume of 2
Consolidated is done, The values of q and
volumetric strain are measured at axial strain, 0, 2
and 10 percent (failure) . The value of N is equal
to 3 and A is equal to 0.2. Graph of all-round
stress on initial all-round stress
Draw the initial all-round stress in terms of
section
1.A dry sand is known to have an angle of internal friction of 29. A triaxial test is planned, where the confining pressure will be 41 kPa. What is the maximum axial stress, in kPa, (major principal stress) that can be applied? Calculate the value to 1 decimal place. Do not provide units in your answer.
2.A clay soil is subjected to a triaxial test under unconsolidated-undrained conditions. At failure, the major and minor principal stresses are 8401 psf and 4875 psf, respectively. What is the shear strength of this soil if the confining pressure is doubled? Provide your answer in psf with no decimals.
Chapter 2 Solutions
Principles of Foundation Engineering (MindTap Course List)
Ch. 2 - Prob. 2.1PCh. 2 - Prob. 2.2PCh. 2 - Prob. 2.3PCh. 2 - Prob. 2.4PCh. 2 - Prob. 2.5PCh. 2 - Prob. 2.6PCh. 2 - Prob. 2.7PCh. 2 - Prob. 2.8PCh. 2 - Prob. 2.9PCh. 2 - Prob. 2.10P
Ch. 2 - Prob. 2.11PCh. 2 - Prob. 2.12PCh. 2 - Prob. 2.13PCh. 2 - Prob. 2.14PCh. 2 - Prob. 2.15PCh. 2 - For a normally consolidated soil, the following is...Ch. 2 - Prob. 2.17PCh. 2 - Prob. 2.18PCh. 2 - Prob. 2.19PCh. 2 - Prob. 2.20PCh. 2 - Prob. 2.21PCh. 2 - Prob. 2.22PCh. 2 - Prob. 2.23PCh. 2 - Prob. 2.24PCh. 2 - Prob. 2.25PCh. 2 - Prob. 2.26PCh. 2 - Prob. 2.27P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- A consolidated-drained triaxial test on a sand yields the results:All-around confining pressure = σ3 = 30 lb/in2Added axial stress at failure = Δσ = 96 lb/in2Determine the shear stress parameters (i.e., Φ' and c')arrow_forwardA triaxial shear test was performed on a well-drained sand sample. The normal stress on the failure plane and the shear stress on the failure plane, at failure were determined to be 6100 psf and 4600 psf, respectively. a. Determine the angle of internal friction of the sand? b. Determine the angle of the failure plane? c. Determine the maximum principal stress? Please answer this asap. For upvote. Thank you very mucharrow_forward10-14. The state plane stress in a mass of dense cohesionless sand is described by the following stresses: Normal stress on horizontal plane Normal stress on vertical plane = 200 kPa Shear stress on horizontal and vertical planes 370 kPa 80 kPa %3! Determine by means of the Mohr circle the magnitude and direc- tion of the principal stresses. Is this state of stress safe against failure? (After A. Casagrande.)arrow_forward
- 2. A triaxial shear test was performed on a well-drained sand sample. The normal stress on the failure plane and the shear stress on the failure plane, at failure was determined to be 6,300 psf and 4,200 psf, respectively. a. Determine the angle of internal friction of the sand. b. Determine the angle of failure plane. c. Determine the maximum principal stress.arrow_forwardA sample of dry sand is subjected to a tri- axial test. The angle of internal friction is 36.6°. The minor principal stress is 192 KPa. Compute the effective normal stress in KPa at the point where shear occurs at the failure plane.arrow_forward2. The state plane stress in a mass of dense cohesionless sand (c=0) is described by the following stresses: Normal stress on horizontal plane = 100 kPa Normal stress on vertical plane = 50 kPa Shear stress on horizontal and vertical planes = ± 30 kPa Determine by means of the Mohr circle the magnitude and direction of the principal stresses. Is this state of stress safe against failure assuming φ= 30o?arrow_forward
- A consolidated-undrained test determines that the shear strength of a normally consolidated clay is given by τf = σ’tan 27o. The confining pressure is 150 kPa, and deviator stress at failure is 120 kPa.• Find the consolidated-undrained friction angle• Pore water pressure developed in the specimen at failureFinal answer should be in 3 decimal places.arrow_forward7.12 A sand specimen was subjected to a drained shear test using hollow cylin- der test equipment. Failure was caused by increasing the inside pressure while keeping the outside pressure constant. At failure, o, = 193 kN/m² and o; = 264 kN/m². The inside and outside radii of the specimen were 40 and 60 mm, respectively. (a) Calculate the soil friction angle. (b) Calculate the axial stress on the specimen at failure.arrow_forward5. [Shear Strength] ( e). In a series of unconsolidated-undrained triaxial tests on speciments of a fully saturdated clay, the following results were obtained at failure. Minor Principal Stress (КРа) 200 400 600 Major Principal Stress 422 618 820 Calculate the following: a. Cohesion b. Angle of internal frictionarrow_forward
- Triaxial tests performed on samples of aeolin sand. The failure conditions in terms of effective stress are (ov, 0h) = (515, 100), (1250, 200), (3500, 400), and (5325, 800) kPa. Using (s, t) space, determine the cohesion and friction angle. What is the orientation of the major principal stress with respect to the failure plane? Determine this graphically.arrow_forwardA consolidated-drained tri-axial test was conducted on a normally consolidated clay. The results are as follows: 03 = 276 kN/m? (Aoa)f = 276 kN/m² Determine a. Angle of friction, o' b. Angle 0 that the failure plane makes with the major principal plane c. Find the normal stress o' and the shear stress tf on the failure plane d. Determine the effective normal stress on the plane of maximum shear stress of Effective stress failure envelope ↑ B of 20 276 kN/m2 A oj = 552 kN/m² Normal stress Shear stress © Cengage Learning 2014arrow_forwardin a drained triangle test on consolidated clay the stress and angle area as follows deviator stress is 20 lb/ in ^2 and friction angle is 21 degree calculate the effective confining pressure at failurearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781305081550Author:Braja M. DasPublisher:Cengage LearningFundamentals of Geotechnical Engineering (MindTap...Civil EngineeringISBN:9781305635180Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage LearningPrinciples of Geotechnical Engineering (MindTap C...Civil EngineeringISBN:9781305970939Author:Braja M. Das, Khaled SobhanPublisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781305081550
Author:Braja M. Das
Publisher:Cengage Learning
Fundamentals of Geotechnical Engineering (MindTap...
Civil Engineering
ISBN:9781305635180
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Principles of Geotechnical Engineering (MindTap C...
Civil Engineering
ISBN:9781305970939
Author:Braja M. Das, Khaled Sobhan
Publisher:Cengage Learning