Although liquids, in general, are hard to compress, the compressibility effect (variation in the density) may become unavoidable at the great depths in the oceans due to enormous pressure increase. At a certain depth the pressure is reported to be
(a) Taking the liquid density at the free surface to be
(b) Use Eq. 2-13 to estimate the density for the specified pressure and compare your result with that of part (a).
(a)
The density of water at the specified depth.
Answer to Problem 118P
The density of water at the specified depth is
Explanation of Solution
Given information:
The pressure at a certain depth is
Write the expression for density at a depth.
Here, the partial derivative of density is
Write the expression for ratio of partial derivative of density with respect to pressure.
Here, the pressure at the specified depth is
Substitute
Substitute,
Conclusion:
The density of water at the specified depth is
(b)
The density of water at the specified depth and its comparison with part (a).
Answer to Problem 118P
The density of water at the specified depth is
Explanation of Solution
Write the expression for the density of water using Equation 2-13.
Write the expression for pressure change.
Write the expression for change in density.
Substitute
Here, the coefficient of compressibility is
Substitute,
The value of density obtained in part (a) that is
Conclusion:
The density of water at the specified depth is
The density calculated in part (b) is more exact as the isothermal compressibility of water in part (a) is an approximate value.
Want to see more full solutions like this?
Chapter 2 Solutions
FLUID MECHANICS FUNDAMENTALS+APPS
- The figure shows a 50.-kg frictionless cylindrical piston that floats on 20 mol of compressed air at 45.°C. How far does the piston move if the temperature is increased to 600 °F? (This is an Isobaric process and the piston is at sea level under an atmospheric pressure of 101.3 kPa). The values given in the figure are: 50. Kg, 30.°C, and 10. cm.arrow_forwardThe pressure of the natural gas installation is as follows.As you can see, mercury (mercury), oil (oil) and water (water) fluidsIt is measured with a manometer. Open end of the manometer (X + 85)It is under the influence of kPa ambient pressure. The relative content of mercury and oil (relative to water)density (SG) and density of water (ρwater = 997 kg / m3) is known.Determine the absolute pressure in the installation (X=00)arrow_forwardIf the specific volume is 0.00045 m³/kg and volume is 0.9 liters. Find the (a) Density (b) Mass, (c) Weight density, and (d) Relative density of the liquid. SOLUTION: (i) Density (in kg/m³) = %3D (ii) Mass of liquid (in gm) = (iii) Weight Density (in N/m³) = (iv) Relative density = %3Darrow_forward
- Determine the gage pressure inside a soap bubble of diameter 6 cm at 20°C. Take the surface tension of soap water at 20°C as σs = 0.025 N/m. Find the gage pressure (in Pa)arrow_forwardThe tank of an air compressor has a volume of 2m3 and is filled with air at a temperature of 40 degrees C. If agauge pressure on the tank reads 7.5 bars,what is themass of the air in the tank?arrow_forwardMercury is often used in thermometers. The mercury sits in a bulb on the bottom of the thermometer and rises up a thin capillary as the temperature rises. Suppose a mercury thermometer contains 3.380 g of mercury and has a capillary that is 0.200 mm in diameter. How far does the mercury rise in the capillary when the temperature changes from 0.0C to 25.0C? The density of mercury at these temperatures is 13.596 g/cm^3 and 13.534 g/cm^3, respectively.arrow_forward
- If the specific volume is 0.00115 m/kg and volume is 0.95 liters. Find the (a) Density (b) Mass, (c) Weight density, and (d) Relative density of the liquid. SOLUTION: (i) Density (in kg/m3) = (ii) Mass of liquid (in gm) = (iii) Weight Density (in N/m3) = (iv) Relative density =arrow_forwardA fluid of density p is rotating with constant angular velocity w about the central vertical axis of a cylindrical container. (a) Show that the variation in pressure in the radial direction is given by dP = pwr. dr (b) If the pressure is at the axis of rotation (r = 0) is Pc, show that the pressure P(r) at any point r is given by 1 P(r) = P. + pw²r?. (c) Show that the liquid surface is a paraboloid: the horizontal cross section of the liquid is a circle and the vertical cross section is a parabola given by w?r2 y = 2g Note: This is a “problem to prove." Your objective is to construct a proof or rational argument based on principles of physics and mathematics that connect given or known information to the stated result. rarrow_forward3 A fluid of density 1200 kg/m° at 1 atm pressure is compressed to 101 atm pressure isothermally. If the isothermal compression is 4.8, 105 atm. -1 the 3. increase in density in kg/m of fluid isarrow_forward
- can you answer this question?arrow_forwardThe basic barometer can be used as an altitude measuring device in airplanes. The ground control reports a barometric reading of 753mmHg while the pilot's reading is 690mmHg. Estimate the altitude of the plane from ground level if the average air density is 1.20 kg.m-3 and the barometer fluid is mercury, PHg=13600 kg.m3. To solve this problem determine the atmospheric pressure on the ground and then in the air using the barometric pressure readings. Then using the pressure difference between the ground and the plane, the altitude can be derived by considering a column of air from the ground up to the plane, of constant density, in a similar manner to the barometer. [h=714m]arrow_forwardA 3 ft high 4.653 ft diameter cylinder tank contains 0.15 slug of gas at 80°F and gauge pressure of 47 in Hg (a) what is the temperature in °C and °R and K? (b) what is the gas specific volume and density? (c) what is the absolute pressure in Psi and in kPa?arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY