Traffic and Highway Engineering
5th Edition
ISBN: 9781305156241
Author: Garber, Nicholas J.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 19, Problem 3P
Discuss the process of lime stabilization, and indicate the soil characteristics for which it is most effective.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
What is the basic objective of the various soil stabilization procedures, and how do the stabilizing additives accomplish this objective?
Q2) Answer the followings:
i-Why is cool clinker interground with gypsum in manufacture of Portland cement?
2- Under what conditions would you recommend the use of rapid hardening
cement?
3- What are the factors governing the desired aggregate grading?
Relationship Between Particle Size Analysis and Moisture Content.
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- 1. In order to determine the particle size distribution of a soil/aggregates, what type of test should be conducted? 2. It is the lowest sieve size opening thru which the entire amount of aggregates is required to pass. 3. One quality test of cement represents. 4. Cement factor of Class "A" concrete? 5. In testing of cement specific gravity, what is the liquid used in the Le Chatelier flask? 6. The means by which desired standards are checked for conformance to the requirements set for the project or each item in the undertaking. 7. Rounded or water torn pebbles, no cohesion or plasticity and crunchy under feet. ( 2mm to 75 mm). 8. Gritty and loose grains, no plasticity or cohesion. (0.05 mm - 2 mm). 9. The amount of water in the soil. 10. Defined as the weight per unit volume. 11. Mixture of water and cement. 12. Mixture of water, sand and cement. 13. Mixture of fine and coarse aggregates with cement and water. 14. Made from combination of limestone, marl or other calcareous materials…arrow_forwarda. What is soil nailing, grouting?b. What are the materials involved?c. What are the situations requiring soil nailing (grouting)? d. Does grouting impact the soil properties? If it does, as an engineer, how will you prevent soil contamination with grouting?arrow_forward7. Define yield of cement in slurry design.arrow_forward
- Q1. Using the sieve results of a batch of sand and gravel shown in the table below, calculate the fineness modulus for the Sand and Gravel blend if the P sand is 40% and P * .Gravel is 60% Sieve No. % Retained Sieve No. % Retained (Sand) (Gravel) 3/8" 1.5" No. 4 1" 6. No. 8 3 0.75" 29 No. 16 15 0.5" 35 No. 30 39 3/8" 26.5 No. 50 30 No. 4 1 No. 100 12 No. 8 0.5 No. 200 1 No. 16arrow_forwardDetermine the amount of water needed to achieved the normal consistency of 650 grams cement by using Vicat apparatus. The paste shall be of normal consistency when the rod settles to a point 10 ± 1 mm below the original surface in 30 seconds after being release. Determine the moisture content in percent if the rod penetration is 10 mm. a. 34.17% b. 41.23% c. 43.70% d. 54.06% e. 46.62%arrow_forwardQ1: A: define the following: Steel corrosion, seasoning, fly ash, flash point, grout B: A severe weathering clay brick was tested for absorption and saturation coefficient according to ASTM C67 procedure and produced the following data: Dry mass of specimen = 2.186 kg Saturated mass after 24-hr submersion in cold water = 2.453 kg Saturated mass after 5-hr submersion in boiling water = 2.472 kg Calculate absorption by 24-hr submersion, absorption by 5-hr boiling, and saturation coefficient. Does the brick satisfy the ASTM requirements?arrow_forward
- Determine the amount of water needed to achieved the normal consistency of 650 grams cement by using Vicat apparatus. The paste shall be of normal consistency when the rod settles to a point 10 ± 1 mm below the original surface in 30 seconds after being release. Determine the moisture content in percent if the rod penetration is 10 mm.arrow_forwardA soil has a pH of 5.5, a tillage depth of 6 inches and a Ca content of 5 meq/100g, Mg of 1 meq/100g, K content 3 meq/ 100g, and exchangeable acidity of 1 meq/100g of soil. Calculate the Percent base saturation Calculate the lime requirement in ECCE (lbs/ac) to achieve a DBS of 95%arrow_forwardWater-cement ratio = 0.50 Water 191.6 liter The required cement content will bearrow_forward
- soil mechanics Q1-a-- Define the weathering,and discusses the types of weathering including outcome of each type b) Define Liquid limit, plastic limit, and shrinkage limitarrow_forwardwhat are the effects of the Acid Attack Test, Chloride Attack Test, and Sulphate Attack Test on the performance of geopolymer concrete based GGBS?arrow_forwardREVIEW QUESTIONS 1. (a) Explain how the following factors affect construction material choice: (i) resource utilization in the choice of construction materials; (ii) social costs and shadow prices. (b) Define the following for cement: (i) hydration; (ii) setting. (c) Briefly describe the Pozzolana as a building material. 2. (a) Outline three disadvantages of soil as a construction material. (b) During the bar shrinkage test the following results were obtained: • Length of wet bar = 600 mm • Length of dry bar = 420 mm Find the shrinkage ratio and state the conclusion that may be drawn from this result. (c) Briefly describe how burnt (soil) bricks are made. 3. (a) Name five methods for seasoning wood. (b) Briefly outline the Bethel full-cell process of timber preservation.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Traffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning
Traffic and Highway Engineering
Civil Engineering
ISBN:9781305156241
Author:Garber, Nicholas J.
Publisher:Cengage Learning
The Science Inside Concrete Binders; Author: Dow;https://www.youtube.com/watch?v=GZq3Cyn2mVE;License: Standard Youtube License