Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133128741
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 19, Problem 34QLP
Does the pull-in defect (sink marks) shown in Fig. 19.32c also occur in metal-forming and casting processes? Explain.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
For sand-casting a steel rectangular plate with dimensions 80mm×120mm×20mm, a cylindrical
riser has to be designed. The height of the riser is equal to its diameter. The total solidification
time for the casting is 2 minutes. In Chvorinov‟s law for the estimation of the total solidification
time, exponent is to be taken as 2. For a solidification time of 3 minutes in the riser, the diameter
(in mm) of the riser is ____
A flat plate is to be cast in an open mold whose bottom has a square shape of 12.5 cm by 12.5 cm. The
mold is 7.0 cm deep. A total of 350 cm³ of molten aluminum is poured into the mold. Solidification
shrinkage is known to be 6.25%, which is a volumetric contraction, not a linear contraction. Table 7.1
lists the linear shrinkage due to thermal contraction after solidification. If the availability of molten
metal in the mold allows the square shape of the cast plate to maintain its square dimension until
solidification is completed, determine the final dimensions (width and height) of the plate.
A riser in the shape of a sphere is to be designed for a sand casting mould at Simon Castings. The casting is a rectangular plate, with length = 400 mm, width = 250 mm, and thickness = 15 mm. If the total solidification time of the casting itself is known to be 7 min, determine the diameter of the riser so that it will take 30% longer for the riser to solidify.
Chapter 19 Solutions
Manufacturing Engineering & Technology
Ch. 19 - What are the forms of raw materials for processing...Ch. 19 - What is extrusion? What products are produced by...Ch. 19 - Describe the features of an extruder screw and...Ch. 19 - How are injection-molding machines rated?Ch. 19 - What is (a) a parison, (b) a plastisol, and (c) a...Ch. 19 - How is thin plastic film produced?Ch. 19 - List several common products that can be made by...Ch. 19 - What similarities and differences are there...Ch. 19 - Explain the difference between potting and...Ch. 19 - What is thermoforming?
Ch. 19 - Describe runner, gate, sprue, and well.Ch. 19 - Describe the advantages of cold-forming plastics...Ch. 19 - What are the characteristics of filament-wound...Ch. 19 - Describe the methods that can be used to make...Ch. 19 - What is pultrusion? Pulforming?Ch. 19 - How are very thin plastic film produced?Ch. 19 - What process is used to make foam drinking cups?Ch. 19 - If a polymer is in the form of a thin sheet, is it...Ch. 19 - How are polymer fibers made? Why are they much...Ch. 19 - What are the advantages of coextrusion?Ch. 19 - Explain how latex rubber gloves are made.Ch. 19 - Describe the features of a screw extruder...Ch. 19 - Explain why injection molding is capable of...Ch. 19 - Prob. 24QLPCh. 19 - Explain the reasons that some plastic-forming...Ch. 19 - Describe the problems involved in recycling...Ch. 19 - Can thermosetting plastics be used in injection...Ch. 19 - Inspect some plastic containers, such as those...Ch. 19 - An injection-molded nylon gear is found to contain...Ch. 19 - Explain why operations such as blow molding and...Ch. 19 - Prob. 31QLPCh. 19 - Typical production rates are given in Table 19.2....Ch. 19 - What determines the cycle time for (a) injection...Ch. 19 - Does the pull-in defect (sink marks) shown in Fig....Ch. 19 - What determines the intervals at which the...Ch. 19 - Identify processes that would be suitable for...Ch. 19 - Identify processes that are capable of producing...Ch. 19 - Inspect several electrical components, such as...Ch. 19 - Inspect several similar products that are made of...Ch. 19 - What are the advantages of using whiskers a...Ch. 19 - Construct a table that lists the main...Ch. 19 - Estimate the die-clamping force required for...Ch. 19 - A 2-Iitcr plastic beverage bottle is made by blow...Ch. 19 - Consider a Styrofoam drinking cup. Measure the...Ch. 19 - In Fig. 19.2, what flight angle, , should be used...Ch. 19 - Make a survey of a variety of sports equipment,...Ch. 19 - Explain the design considerations involved in...Ch. 19 - Give examples of several parts suitable for insert...Ch. 19 - Give other examples of design modifications in...Ch. 19 - With specific examples, discuss the design issues...Ch. 19 - Die swell in extrusion is radially uniform for...Ch. 19 - Inspect various plastic components in a typical...Ch. 19 - It is well known that plastic forks, spoons, and...Ch. 19 - Prob. 55SDPCh. 19 - Make a survey of the technical literature, and...Ch. 19 - Prob. 57SDPCh. 19 - Prob. 58SDPCh. 19 - Prob. 59SDPCh. 19 - Examine some common and colorful plastic poker...Ch. 19 - Obtain different styles of toothpaste tubes,...Ch. 19 - By incorporating small amounts of blowing agent,...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- a riser in the shape of a sphere is to be designed for a sand casting mold. the casting is a rectangular plate, with length 200mm, width 100mm, and thickness 18mm. if the total solidification time of the casting itself is known to be 3.5 mm, determine the diameter of the riser so that it will take 25% longer for the riser to solidify. assume a value of 2 for ‘n’ m( the exponent in chvorinov’s rule). know the volume and surface area of a sphere.arrow_forward27. A Titanium part built by Selective Laser Melting (SLM) has a height of 95mm. Estimate the total build time for the part in hours and minutes (excluding set-up and clean-up processes) if each layer is 50 µm thick; the laser scanning time per layer is an average of 43 seconds; the powder recoating time for each layer is 30 seconds; and every 5th layer is scanned twice by the laser for in-situ heat treatment.arrow_forward(1) In sand casting, the volumetric size of the pattern is: (a) bigger than, (b) the same as, or (c) smaller than the cast part (2) Machining processes include which of the following (two correct answers): (a) casting, (b) drilling, (c) extrusion, (d) forging, (e) shaping, (f), and painting? (3) Aluminum sections used for making metal doors and windows are made by which process: (a) Rolling, (b) welding, (c) extrusion, (d) turning. (4) The average flow stress is the flow stress multiplied by which of the following factors: (a) n, (b) (1-n), (c) 1/n, or (d) 1/(1+n), where n is the strain hardening exponent? (5) The strength of a brazed joint is typically (a) equal to, (b) stronger than, or (c) weaker than soldered joint? (6) Thread cutting operation is normally performed on which one of the following machine tools: (a) drill press, (b) lathe, (c) milling machine, (d) planer, or (e shaper?arrow_forward
- A mould has downsprue whose length is 20 cm and the cross sectional area at the base of the downsprue is 1 cm2. The downsprue feeds a horizontal runner leading into the mould cavity of volume 1000 cm³. The time required to fill the mould cavity will bearrow_forwardQUESTION 1 (a) Powder Metallurgy (PM) enables the processing of materials with very high melting points, including refractory metals such as tungsten, molybdenum and tantalum. Such metals are very difficult to produce by melting and casting and are often very brittle in the cast state. As a manufacturing engineer, state and explain at least SIX (6) limitations of powder metallurgy that is not applicable in particular engineering industries. In a case where you were assigned to use powder metallurgy in metal forming, justify at least THREE (3) PM requirements. (b) A coil of sheet metal is placed in a furnace and annealed in order to improve its ductility. Nonetheless, it is found that the sheet metal has a lower limiting drawing (LDR) than it had before the annealing process. Describe the meaning of LDR and explain the reasons for this behaviour by referring to the microstructure and materials' properties point of view for different types of materials. In addition, discuss the process…arrow_forward2. In the casting of steel under certain mould conditions, the mould constant in Chvorinov's rule is known to be 4.0 min/cm?, based on previous experience. The casting is a flat plate whose length is 25 cm, width is 8 cm, and thickness is 2.5 cm. Exponent n is taken to have a value of 2. Determine how long it will take for the casting to solidify.arrow_forward
- Please show your solution clearly thank you (9)arrow_forwardA flat plate is to be cast in an open mold whose bottom has a square shape that is 200 mm by 200 mm. The mold is 40 mm deep. A total of 106 mm3 of molten aluminum is poured into the mold. Solidification shrinkage is known to be 6.0%. The linear shrinkage due to thermal contraction after solidification is 1.3%. If the availability of molten metal in the mold allows the square shape of the cast plate to maintain its 200 mm by 200 mm dimensions until solidification is completed, determine the final dimensions of the plate.arrow_forwardA thin steel disk of an oil separator of 100mm outside diameter is shrunk onto a solid steel shaft of 20mm diameter. The system is to be designed to make sure the disc does not become loose at speeds lower than 100000rev/min. Determine the shrinkage allowance required in order to avoid separation disc and shaft, at a speed of 100000rev/min. For the material assume a Young's Modulus, Poisson Ratio and density of 210GPa, 0.3 and 7850kg/m³ respectively.arrow_forward
- A slab of 1500 mm x 750 mm x 500 mm is required to be cast using a sand casting process. It was observed previously that the total solidification time (T) for this casting = 1.6 min. Find out the cylindrical riser dimensions (diameter to height ratio = 1) for a solidification time T = 5 min.arrow_forwardلانقطة واحدة of Warm working The advantages over cold working are: 1) forces and power are higher,2) more intricate work geometries possible, and 3) need for annealing may be reduced .or eliminated T F Blow molding is an important industrial process for making one- piece hollow plastic parts with thick .walls T Sly The sequence of the Blow Molding is automated and often integrated with downstream operations such .as bottle filling and labeling T لنقطة واحدةarrow_forwardDescribe the die casting process in detail. Use neat sketches for clarity. Differentiate clearly between hot-chamber die casting and cold-chamber die casting processes. What is the difference between true centrifugal and semi-centrifugal casting? Describe the centrifugal casting process in detail. Use neat sketches to elaborate your description.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
The Laws of Thermodynamics, Entropy, and Gibbs Free Energy; Author: Professor Dave Explains;https://www.youtube.com/watch?v=8N1BxHgsoOw;License: Standard YouTube License, CC-BY