Statics and Mechanics of Materials (5th Edition)
5th Edition
ISBN: 9780134382593
Author: Russell C. Hibbeler
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 17.3, Problem 44P
To determine
Show that the critical load on the column
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
5. Two C310x45 channels are latticed together so they have equal moments
of inertia about the principal axes. Determine the minimum length of
column having this section, assuming pinned ends, E = 200 GPa, and a
proportional limit of 240 MPa. What safe load will the column carry for the
length of 12 m with a factor of safety of 2.5?
For C310x45, take I = 67.3x10-6 m4
%3D
Ans L = 9.89 m, F = 738 kN
An
aluminum alloy tube with an outside diameter of 3.1 in. and a wall thickness of 0.36 in. is used as a 16-ft-long column. Assume that E
= 9300 ksi and that pinned connections are used at each end of the column. Determine the slenderness ratio L/r and the Euler buckling
load Per for the column.
Answers:
L/r=
Por=
kips
kips.
Determine the Euler Buckling axial compressive load of W 12 x 72 section having a length of L=48 ft and fixed ends, Pe=
Assume that the column is made of A441 steel with E = 29 x 103 ksi, and assume that the normal stress generated by P is still within the elastic range of the material.
Reminder: use the minimum moment of inertial of the cross section. Please calculate your answer to 1 decimal place.
Lft
Fixed end
Fixed end
Chapter 17 Solutions
Statics and Mechanics of Materials (5th Edition)
Ch. 17.3 - A 50-in.-long steel rod has a diameter of 1 in....Ch. 17.3 - A 12-ft wooden rectangular column has the...Ch. 17.3 - Prob. 3FPCh. 17.3 - A steel pipe is fixed supported at its ends. If it...Ch. 17.3 - Determine the maximum force P that can be...Ch. 17.3 - The A992 steel rod BC has a diameter of 50 mm and...Ch. 17.3 - Determine the critical buckling load for the...Ch. 17.3 - Prob. 2PCh. 17.3 - The aircraft link is made from an A992 steel rod....Ch. 17.3 - Rigid bars AB and BC are pin connected at B. If...
Ch. 17.3 - A 2014-T6 aluminum alloy column has a length of 6...Ch. 17.3 - Prob. 6PCh. 17.3 - Prob. 7PCh. 17.3 - Prob. 8PCh. 17.3 - A steel column has a length of 9 m and is fixed at...Ch. 17.3 - A steel column has a length of 9 m and is pinned...Ch. 17.3 - The A992 steel angle has a cross-sectional area of...Ch. 17.3 - The 50-mm-diameter C86100 bronze rod is fixed...Ch. 17.3 - Determine the maximum load P the frame can support...Ch. 17.3 - Prob. 14PCh. 17.3 - Prob. 15PCh. 17.3 - An A992 steel W200 46 column of length 9 m is...Ch. 17.3 - Prob. 17PCh. 17.3 - Prob. 18PCh. 17.3 - Prob. 19PCh. 17.3 - Prob. 20PCh. 17.3 - Prob. 21PCh. 17.3 - The deck is supported by the two 40-mm-square...Ch. 17.3 - Prob. 23PCh. 17.3 - Prob. 24PCh. 17.3 - Prob. 25PCh. 17.3 - Prob. 26PCh. 17.3 - Prob. 27PCh. 17.3 - The linkage is made using two A992 steel rods,...Ch. 17.3 - The linkage is made using two A-36 steel rods,...Ch. 17.3 - The linkage is made using two A-36 steel rods,...Ch. 17.3 - The steel bar AB has a rectangular cross section....Ch. 17.3 - Determine if the frame can support a load of P =...Ch. 17.3 - Determine the maximum allowable load P that can be...Ch. 17.3 - Prob. 34PCh. 17.3 - Prob. 35PCh. 17.3 - The members of the truss are assumed to be pin...Ch. 17.3 - The members of the truss are assumed to be pin...Ch. 17.3 - The truss is made from A992 steel bars, each of...Ch. 17.3 - The truss is made from A992 steel bars, each of...Ch. 17.3 - The steel bar AB of the frame is assumed to be pin...Ch. 17.3 - Prob. 41PCh. 17.3 - Prob. 42PCh. 17.3 - Prob. 43PCh. 17.3 - Prob. 44PCh. 17.3 - Consider an ideal column as in Fig. 1710d, having...Ch. 17.4 - Prob. 46PCh. 17.4 - Prob. 47PCh. 17.4 - The W10 12 structural A-36 steel column is used...Ch. 17.4 - The aluminum column is fixed at the bottom and...Ch. 17.4 - Prob. 50PCh. 17.4 - The aluminum rod is fixed at its base and free and...Ch. 17.4 - Prob. 52PCh. 17.4 - Prob. 53PCh. 17.4 - Prob. 54PCh. 17.4 - The wood column is pinned at its base and top....Ch. 17.4 - Prob. 56PCh. 17.4 - Prob. 57PCh. 17.4 - Prob. 58PCh. 17.4 - Prob. 59PCh. 17.4 - Prob. 60PCh. 17.4 - Prob. 61PCh. 17.4 - Prob. 62PCh. 17.4 - The W14 53 column is fixed at its base and free...Ch. 17.4 - Prob. 64PCh. 17 - The wood column is 4 m long and is required to...Ch. 17 - Prob. 2RPCh. 17 - A steel column has a length of 5 m and is free at...Ch. 17 - Prob. 4RPCh. 17 - Prob. 5RPCh. 17 - If P = 15 kip, determine the required minimum...Ch. 17 - Prob. 7RPCh. 17 - The W200 46 wide-flange A992-steel column can be...Ch. 17 - The wide-flange A992 steel column has the cross...Ch. 17 - The wide-flange A992 steel column has the cross...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Determine the allowable axial load Pallowfor a steel pipe column that is fixed at the base and free at the top (see figure) for each of the following lengths: L = 6 ft, 9 ft, 12 ft, and 15 ft. The column has an outside diameter d = 6.625 in. and wall thickness t = 0.280 in, (Assume E = 29,000 ksi and y= 36 ksi.)arrow_forwardAn aluminum box column with a square cross section is fixed at the base and free at the top (sec figure). The outside dimension b of each side is 100 mm and the thickness t of the wall is 8 mm. The resultant of the compressive loads acting on the top of the column is a force P = 50 kN acting at the outer edge of the column at the midpoint of one side. What is the longest permissible length Lmaxof the column if the deflection at the top is not to exceed 30 mm? (Assume E = 73 GPaarrow_forwardDetermine the maximum permissible length Lmaxfor a steel pipe column that is fixed at the base and free at the top and must support an axial load P = 500 kN (see figure). The column has an outside diameter d = 200 mm, wall thickness; = 10 mm, E = 200 GPa, and y = 250 MPa.arrow_forward
- An aluminum tube AB with a circular cross section has a sliding support at the base and is pinned at the top to a horizontal beam supporting a load Q = 200 kN (sec figure). Determine the required thickness t of the tube if its outside diameter d is 200 mm and the desired factor of safety with respect to Eu 1er buckling is n = 3.0. (Assume E = 72 GPa.)arrow_forwardThe rigid bar AB with a length of 5m, is attached to two vertical rods and ishorizontal before the uniformly varying load of zero intensity at point A and 10kN/mat point B is applied. The rod at A is steel with L=3m, A=300 mm2 and E=200GPa. Therod in B is aluminum with L=4m, A=500mm2 and E = 70GPa. Determine the verticaldisplacement of the bar at a point where the resultant of the load is acting.arrow_forwardThe rigid arm AB is attached to the end of the solid circular steel rod BC. The rod is supported by bearings at B and a fixed support at C. The bearings at B prevent rod BC from translating up, down, left, or right, but the bearings do allow rod BC to rotate freely about the x axis at B. It is required that the vertical deflection of point A not exceed 0.25 in. when a load of P = 700 lb is applied at A. Determine the minimum diameter needed for rod BC. Use a = 18 in. and b = 45 in. The modulus of rigidity of the rod is G = 11×106 psi. A P Answer: dmin = i a B b in. Carrow_forward
- A 75 mm diameter compound bar is constructed by shrinking a circularbrass bush onto the outside of a 45 mm diameter solid steel rod. If thecompound bar is then subjected to an axial compressive load of 170 kN,determine the load carried by the steel rod. The modulus of elasticity for steel,Es = 200 GN/m2 , and brass, Eb = 100 GN/m2arrow_forwardAssume portion ABC of the rod is made of steel (E4e= 200 GPa , v=0.3) and portion CD is made of aluminum (E,lumi = 70 GPa , v=0.25). A 1.75 m Area = 800 mm² 120 kN B 1.25 m C Area = 500 mm² 1.5 m 80 kN D 60 kN The deflection of point C is_ The resulting change in diameter of portion AB of the bar is_arrow_forward4. The cable will fail when subjected to a tension of 8000 N. Determine the largest vertical load P the frame will support and compute theresultant internal loadings at the cross section through point C. Answer: P = 2133.33 N, Mc = 1600 Nm, Nc = 8000 N, Vc = 2133.33 N 0.1 m 0.5 m C 0.75 m- -0.75 m- -0.75 m-arrow_forward
- The steel column BD (yield stress = 280 N/mm2) carries a compressive load in the following structure with a factor of safety of 2.0. Note that the support A is only subjected to a horizontal reaction. Find the allowable value of load P if the column BD has cross-sectional area A=8500 mm². Give answer in kN. A B L/3 2L/3 PV L Frame |Darrow_forwardTwo vertical steel wires each 1.5mm diameter and 1.2m long support a light rod over a span of 0.3m. A concentrated load of 250N is then applied vertically downwards at a point 0.1m from one of the wires. Determine the load, stress and extension on each wire and the angular displacement of the rod from the horizontal assuming it does not bend. Use E=200 GPa (Complete Solution)arrow_forwardBoth portions of the rod ABC are made of an aluminum for which E = 70 GPa. What is the value of Q in kN so that the deflection at A is zero if P = 34 kN?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Column buckling; Author: Amber Book;https://www.youtube.com/watch?v=AvvaCi_Nn94;License: Standard Youtube License