Concept explainers
The velocity of the rod AB relative to cylinder DE when end B of the rod strikes end E of the cylinder.
Answer to Problem 17.93P
Velocity of the rod relative to cylinder:
Explanation of Solution
Given information:
The mass of the rod:
Length of the rod is 800 mm.
Length of cylinder DE is 240 mm.
Angular velocity of the assembly:
Velocity of the end B of the rod towards the cylinder is 75 mm/s.
The centroidal moment of inertia of the cylinder about a vertical axis is 0.025 kg.m2.
Calculations:
From the schematic shown above:
Conclusion:
The velocity of the rod AB relative to cylinder DE when end B of the rod strikes end E of the cylinder is
Want to see more full solutions like this?
Chapter 17 Solutions
Vector Mechanics for Engineers: Dynamics
- Prob.2. The length of crank and connecting rod of a horizontal reciprocating engine are 100 mm and 500 mm respectively. The crank is rotating at 400 r.p.m. When the crank has turned 30° from the inner dead centre (IDC), find analytically – (i) Acceleration of the piston (ii) Velocity of the pistonarrow_forwardEach of the gears A and B has a mass of 2.4 kg and a radius of gyration of 60 mm, while gear C has a mass of 12 kg and a radius of gyration of 150 mm. A couple M of constant magnitude 10 N.m is applied to gear C determine a ) the number of revolutions of gear C required for its angular velocity to increase from 100 to 450 rpm, (b) the corresponding tangential force acting on gear A.arrow_forwardIn the helicopter shown; a vertical tail propeller is used to pre- vent rotation of the cab as the speed of the main blades is changed. Assuming that the tail propeller is not operating determine the final angular velocity of the cab after the speed of the main blades has been changed from I80 to 240 rpm. (The speed of the main blades is measured relative to the cab, and the cab has a centroidal moment of inertia of 650 lb.ft.s2. Each of the four main blades is assumed to be a slender rod 14 ft weighing 55 lb.)arrow_forward
- A uniform slender rod AB A uniform slender rod A of the rod is struck by a hammer that delivers an impulse that is perpendicular to the rod. In the subsequent motion, determine the distance b through which the rod will move each time it completes a full revolution.arrow_forwardTwo uniform rods AB and CE, each of weight 3 lb and length 2 ft, are welded to each other at their midpoints. Knowing that this assembly has an angular velocity of constant magnitude w = 12 rad/s, determine the magnitude and direction of the angular momentum HD of the assembly about D.arrow_forwardQ3. Two identical slender rods AB and BC are welded together to form an L-shaped assembly. The assembly is pressed against a spring at D and released from the position shown. Knowing that the maximum angle of rotation of the assembly in its subsequent motion is 90° counterclockwise, determine the magnitude of the angular velocity of the assembly as it passes through the position where rod AB forms an angle of 30° with the horizontal. h D B 1 0.4 m 0.4 marrow_forward
- In the gear arrangement shown, gears A and C are attached to rod ABC, that is free to rotate about B, while the inner gear B is fixed. Knowing that the system is at rest, determine the magnitude of the couple M that must be applied to rod ABC, if 2.5 s later the angular velocity of the rod is to be 240 rpm clockwise. Gears A and C ABC weighs 4 lb.arrow_forwardThe rotor of an electric motor has an angular velocity of 3600 rpm when the load and power are cut off. The 121-lb rotor, which has a centroidal radius of gyration of 9 in., then coasts to rest. Knowing that kinetic friction results in a couple of magnitude 2.5 lb-ft exerted on the rotor, determine the number of revolutions that the rotor executes before coming to rest. The number of revolutions that the rotor executes before coming to rest isarrow_forward) Two uniform rods AB and CE, each of weight 20 N and length 1 m, are welded to each other at their midpoints. Knowing that this assembly has an angular velocity of constant magnitude ω = 8 rad/s, determine the kinetic energy of the assemblyarrow_forward
- R B R с D The motion of a slender rod of length 0.545 m is guided by pins at A and B which slide freely in slots cut in a vertical plate as shown. If end B is moved slightly to the left and then released, determine the angular velocity of the rod and the velocity of its mass center (a) at the instant when the velocity of end B is zero, (b) as end B passes through Point D.arrow_forwardEach of the gears A and B has a mass of 675 g and a radius of gyration of 40 mm, while gear C has a mass of 3.6 kg and a radius of gyration of 100 mm. Assume that kinetic friction in the bearings of gears A, B C produces couples of constant magnitude 0.15 N.m, 0.15 N.m, 0.3 N.m, respectively. Knowing that the initial angular velocity of gear C is 2000 rpm, determine the time required for the system to come to rest.arrow_forward15.55 The end D of the string wound around the core of the yoyo is pulled by vD as shown. If the yoyo rolls withont slipping, determine w of the yoyo and vB of the point B.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY