R R с D The motion of a slender rod of length 0.545 m is guided by pins at A and B which slide freely in slots cut in a vertical plate as shown. If end B is moved slightly to the left and then released, determine the angular velocity of the rod and the velocity of its mass center (a) at the instant when the velocity of end B is zero, (b) as end B passes through Point D.

R R с D The motion of a slender rod of length 0.545 m is guided by pins at A and B which slide freely in slots cut in a vertical plate as shown. If end B is moved slightly to the left and then released, determine the angular velocity of the rod and the velocity of its mass center (a) at the instant when the velocity of end B is zero, (b) as end B passes through Point D.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the mechanism shown, find the angular velocities of both bars, and the velocity of point B.
Two panels A and B are attached with hinges to a rectangular plate and held by a wire as shown. The plate and the panels are made of the same material and have the same thickness. The entire assembly is rotating with an angular velocity w0 when the wire breaks. Determine the angular velocity of the assembly after the panels have come to rest against the plate.
The 10-Ib sphere and 7-ib block (shown in section) are secured to the arm of negligible mass which rotates in the vertical plane about a horizontal axis at O. The 5-Ib plug is released from rest at A and falls into the recess in the block when the arm has reached thehorizontal position. An instant before engagement, the arm has an angular velocity wo = 1.2 rad/s. Determine the angular velocity w(positive if counterclockwise, negative if clockwise) of the arm immediately after the plug has wedged itself in the block.
Arm ACB rotates about Point Cwith an angular velocity of 39 radis counterclockwise. Two friction disks A and Bare pinned at their centers to arm ACB as shown. Know that the disks roll without slipping at the surfaces of contact. 2.4 in. 1.2 in. 0.9 in. 1.5 in. 0.6 in. D Determine the angular velocity of disk B. The angular velocity of disk B is radis . Determine the angular velocity of disk A. The angular velocity of disk A is [ rad/s O Determine the angular velocity of disk A. The angular velocity of disk A is rad/s O.
In the helicopter shown; a vertical tail propeller is used to pre- vent rotation of the cab as the speed of the main blades is changed. Assuming that the tail propeller is not operating determine the final angular velocity of the cab after the speed of the main blades has been changed from I80 to 240 rpm. (The speed of the main blades is measured relative to the cab, and the cab has a centroidal moment of inertia of 650 lb.ft.s2. Each of the four main blades is assumed to be a slender rod 14 ft weighing 55 lb.)
(6) The spring-loaded plunger F has a velocity of 3 m/s in the direction indicated. A roller at corner E of the equilateral triangular member BDE contacts the smooth surface of the plunger. The roller at corner D of member BDE slides freely along the horizontal slot. Member AB is pin connected to member BDE at point B. Determine the angular velocities of members BDE and AB and the velocity of roller D for the instant shown using the Method of Instantaneous Center of Zero Velocity. D E F 45° B. 75 cm A 30 83 cm
(6) The spring-loaded plunger F has a velocity of 3 m/s in the direction indicated. A roller at corner E of the equilateral triangular member BDE contacts the smooth surface of the plunger. The roller at corner D of member BDE slides freely along the horizontal slot. Member AB is pin connected to member BDE at point B. Determine the angular velocities of members BDE and AB and the velocity of roller D for the instant shown using the Method of Instantaneous Center of Zero Velocity. 83cm 45° 75 cm 30
A homogeneous disk of mass m = 4 kg rotates at the constant rate wi = 12 rad/s with respect to arm OA, which itself rotates at the constant rate wz = 4 rad/s about the y- axis, determine: 1. Angular momentum of the disk about point A. 2. Angular momentum of the disk about point O. 3. The force-couple system representing the dynamic reactions at the support. Neglect the mass of of arm OA. 320 min 200 mm T = 100 mm
Determine the rate of change H, of the angular momentum HD of the rod CDE, assuming that at the instant considered the assembly has an angular velocity o = (12 rad/s)i and an angular acceleration a = -(96 rad/s?)i. C A D В Z. 9 in. E 9 in. 3 in. 3 in.
Two shafts the axes of which intersect but are inclined to each other at 20 degreeconnected by means of a universal joint. At what position in the rotation cycle of thedrive shaft (i) velocity ratio will be maximum, minimum and unity (ii) the accelerationis maximum?
Q4: The crank and connecting rod of a theoretical steam engine are 0.5 m and 2 m long, respectively. The crank makes 300 rpm in the counterclockwise direction when it has turned 45° from the inner dead center position. Determine the velocity of the piston and the angular velocity of the connecting rod. 0.5 m 2 m 45 I.D.C. o QD.C.
Q1 The grooved drums in the two systems shown are identical. In both cases, (a) and (b), the system is at rest at time t = 0. Determine the angular velocity of each grooved drum at time t = 4 s. Neglect fric- tion at the pivot O. Ans. (a) w = 119.0 rad/s, (b) w = 72.0 rad/s m = 14 kg, k = 225 mm r. = 325 mm, r, = 215 mm V10(9.81) N 10 kg