Fluid Mechanics: Fundamentals and Applications
4th Edition
ISBN: 9781259696534
Author: Yunus A. Cengel Dr., John M. Cimbala
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Question
Chapter 12, Problem 8EP
To determine
Static pressure and temperature of the air in this state.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The Airbus A-340 passenger plane has a maximum takeoff weight of about 260,000 kg, a length of 64 m, a wing span of 60 m, a maximum cruising speed of 945 km/h, a seating capacity of 271 passengers, a maximum cruising altitude of 14,000 m, and a maximum range of 12,000 km. The air temperature at the crusing altitude is about −60°C. Determine the Mach number of this plane for the stated limiting conditions.
The fluid is heated from 125 degrees Fahrenheit to 225 degrees Fahrenheit. Consider an ideal gas with the following characteristics:
R = 85 ft-lbf/lbm-R
Cp = 0.35 + 0.000325T BTU/lbm-R
If the heating is at constant volume, compute for (a) the change in internal energy, (b) the change in enthalpy, and (c) the change in entropy. If the heating is at constant pressure, compute for (d) the change in entropy, and (e) the value of k at 160 degrees Celsius. If the fluid undergoes an isentropic process, determine (f) non-flow work and (g) steady-flow work. (For item f and g, use the value of k at 160 degrees Celsius). Note: The unit should be in metric system. Should have given, required and the solution.
4-Steam flows through a device with a stagnation pressure of 120 psia, a
stagnation temperature of 7008F, and a velocity of 900 ft/s. Assuming ideal-
gas behavior, determine the static pressure and temperature of the steam at
this state.
Chapter 12 Solutions
Fluid Mechanics: Fundamentals and Applications
Ch. 12 - What is dynamic temperature?Ch. 12 - Calculate the stagnation temperature and pressure...Ch. 12 - Prob. 6PCh. 12 - Prob. 7PCh. 12 - Prob. 8EPCh. 12 - Prob. 9PCh. 12 - Products of combustion enter a gas turbine with a...Ch. 12 - Is it possible to accelerate a gas to a supersonic...Ch. 12 - Prob. 72EPCh. 12 - Prob. 73P
Ch. 12 - Prob. 74PCh. 12 - Prob. 75PCh. 12 - For an ideal gas flowing through a normal shock,...Ch. 12 - Prob. 77CPCh. 12 - On a T-s diagram of Raleigh flow, what do the...Ch. 12 - What is the effect of heat gain and heat toss on...Ch. 12 - Prob. 80CPCh. 12 - Prob. 81CPCh. 12 - Prob. 82CPCh. 12 - Argon gas enters a constant cross-sectional area...Ch. 12 - Prob. 84EPCh. 12 - Prob. 85PCh. 12 - Prob. 86PCh. 12 - Prob. 87EPCh. 12 - Prob. 88PCh. 12 - Prob. 89PCh. 12 - Prob. 90PCh. 12 - Prob. 91PCh. 12 - Prob. 93CPCh. 12 - Prob. 94CPCh. 12 - Prob. 95CPCh. 12 - Prob. 96CPCh. 12 - Prob. 97CPCh. 12 - Prob. 98CPCh. 12 - Prob. 99CPCh. 12 - Prob. 100CPCh. 12 - Prob. 101PCh. 12 - Air enters a 5-cm-diameter, 4-m-long adiabatic...Ch. 12 - Helium gas with k=1.667 enters a 6-in-diameter...Ch. 12 - Air enters a 12-cm-diameter adiabatic duct at...Ch. 12 - Prob. 105PCh. 12 - Air flows through a 6-in-diameter, 50-ft-long...Ch. 12 - Air in a room at T0=300k and P0=100kPa is drawn...Ch. 12 - Prob. 110PCh. 12 - Prob. 112PCh. 12 - Prob. 113PCh. 12 - Prob. 114PCh. 12 - Prob. 115PCh. 12 - Prob. 116EPCh. 12 - A subsonic airplane is flying at a 5000-m altitude...Ch. 12 - Prob. 118PCh. 12 - Prob. 119PCh. 12 - Prob. 120PCh. 12 - Prob. 121PCh. 12 - Prob. 122PCh. 12 - Prob. 123PCh. 12 - An aircraft flies with a Mach number Ma1=0.9 at an...Ch. 12 - Prob. 125PCh. 12 - Helium expands in a nozzle from 220 psia, 740 R,...Ch. 12 - Prob. 127PCh. 12 - Prob. 128PCh. 12 - Prob. 129PCh. 12 - Prob. 130PCh. 12 - Prob. 131PCh. 12 - Prob. 132PCh. 12 - Prob. 133PCh. 12 - Prob. 134PCh. 12 - Prob. 135PCh. 12 - Prob. 136PCh. 12 - Prob. 137PCh. 12 - Prob. 138PCh. 12 - Air is cooled as it flows through a 30-cm-diameter...Ch. 12 - Prob. 140PCh. 12 - Prob. 141PCh. 12 - Prob. 142PCh. 12 - Prob. 145PCh. 12 - Prob. 148PCh. 12 - Prob. 149PCh. 12 - Prob. 150PCh. 12 - Prob. 151PCh. 12 - Prob. 153PCh. 12 - Prob. 154PCh. 12 - Prob. 155PCh. 12 - Prob. 156PCh. 12 - Prob. 157PCh. 12 - Prob. 158PCh. 12 - Prob. 159PCh. 12 - Prob. 160PCh. 12 - Prob. 161PCh. 12 - Prob. 162PCh. 12 - Assuming you have a thermometer and a device to...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Steam flows through a device with a pressure of 120 psia, a temperature of 700°F, and a velocity of 900 ft/s. Determine the Mach number of the steam at this state by assuming ideal-gas behavior with k = 1.3.arrow_forwardHelium enters a converging–diverging nozzle at 0.7 MPa, 800 K, and 100 m/s. What are the lowest temperature and pressure that can be obtained at the throat of the nozzle?arrow_forwardNitrogen enters a converging–diverging nozzle at 700 kPa and 400 K with a negligible velocity. Determine the critical velocity, pressure, temperature, and density in the nozzle.arrow_forward
- For an ideal gas flowing through a normal shock, develop a relation for V2/V1 in terms of k, Ma1, and Ma2.arrow_forwardNitrogen enters a converging–diverging nozzle at 800 kPa and 400 K with a negligible velocity. Determine the critical velocity, pressure, temperature, and density in the nozzle. Use data from the tables. The properties of nitrogen are k = 1.4 and R = 0.2968 kJ/kg·Karrow_forwardAir enters a compressor with a stagnation pressure of 100 kPa and a stagnation temperature of 35°C, and it is compressed to a stagnation pressure of 900 kPa. Assuming the compression process to be isentropic, determine the power input to the compressor for a mass flow rate of 0.04 kg/sarrow_forward
- Consider a gas with a specific heats ratio of 1.48 at the Mach number of 6.5. Determine the strength (the pressure ratio across the shock, p2/p1) of the normal shock.arrow_forwardArgon is accelerated in a nozzle from 32 m/s at 666 K to 441 m/s and 196 kPa. If the heat loss is equal to 5.1 kJ/kg, determine the gas temperature at outlet in K to 1 decimal place. Take the gas constant as 0.2 (kPa m3)/(kg K) and assume constant specific heats cp=0.5 kJ/(kg K) and cv=0.3 kJ/(kg K).arrow_forward1- An ideal gas with k = 1.4 is flowing through a nozzle such that the Mach number is 2.4 where the flow area is 25 cm2. Assuming the flow to be isentropic, determine the flow area at the location where the Mach number is 1.2arrow_forward
- Carbon dioxide flows steadily through a varying cross- sectional-area duct such as a nozzle at a mass flow rate of 3 kg/s. The carbon dioxide enters the duct at a pressure of 1400 kPa and 200°C with a low velocity, and it expands in the nozzle to a pressure of 200 kPa. The duct is designed so that the flow can be approximated as isentropic. Determine the following parameters at each location along the duct that corresponds to a pressure drop of 200 kPa: (i) density; (ii) velocity: (iii) flow area; (iv) mach number. You may assume: • Carbon dioxide is an ideal gas with constant specific heats at room temperature; • Flow through the duct is steady, one-dimensional and isentropic. Use c, 0 846 kJ/kgk andk = 1.289 throughout the calculations, which are the constant-pressure specific heat and specific heat ratio values of carbon dioxide at room temperature. The gas constant of carbon dioxide is R = 0.1889 kJ/kg K.arrow_forwardCarbon dioxide enters an adiabatic nozzle at 1200 K with a velocity of 50 m/s and leaves at 400 K. Assuming constant specific heats at room temperature, determine the Mach number (a) at the inlet and (b) at the exit of the nozzle. Assess the accuracy of the constant specific heat approximation.arrow_forwardWhen an airplane is flying at a constant speed relative to the ground, is it correct to say that the Mach number of this airplane is also constant?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License