Consider steady, adiabatic flow of air through a long straight pipe with A = 0.05 m2. At the inlet section ① the air is at 200 kPa absolute, 60°C, and 146 m/s. Downstream at section ②, the air is at 95.6 kPa absolute and 280m/s. Determine
Want to see the full answer?
Check out a sample textbook solutionChapter 12 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Additional Engineering Textbook Solutions
Fundamentals Of Thermodynamics
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Engineering Mechanics: Statics & Dynamics (14th Edition)
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Statics and Mechanics of Materials (5th Edition)
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
- Air enters a nozzle that has an inlet area of 0.4 m?, at 200 kPa, 500 °C. and 30 m/s. At the exit the conditions are 100 kPa and 443 °C. Part A If the exit area is 45 cm? , determine the steady-state exit velocity. Use the IG flow-state TESTcalc. Express the steady-state exit velocity in meters per second to four significant figures. ΑΣφ vec ? V. = m/s Submit Request Answerarrow_forwardA vessel contains 10 kg of water at 10 x last digit kPa (if last digit is 2 then 10 x 2 = 20 kPa). Determine specific and total internal energy, specific and total enthalpy, and specific and total entropy. Consider different cases/states: I. T = Tsat and x = 0II. T = Tsat and x = 0.5III. T = Tsat and x = 1IV. T = 300 ⁰C (Plot these states on the Tv diagram and label magnitudes. Refer property tables.) very important.arrow_forwardThe refrigerant R134a is passing through the diffuser with the inlet diameter of D1=1 inch; p1=150psi; and V1=1000 ft/s as a saturated vapor. The exit parameters are p2=400 psi, and velocity V2=0.5 ft/s. Heat transfer, Work, and Potential energy changes can be neglected. NOTE: Use English units. For the kinetic energy change do not forget dividing to (778*32.2) conversion factor to obtain Btu/lbm. From NIST tables use BTU/lbm units for the enthalpy. Determine: a.Exit temperature in F; b.Mass flow rate in lbm/s; c.Exit diameter D2 in inches. d.Determine exit temperature.arrow_forward
- Consider steady adiabatic airflow in a duct. At section B,the pressure is 600 kPa and the temperature is 177°C. Atsection D, the density is 1.13 kg/m3 and the temperature is156°C. (a) Find the entropy change, if any. (b) Which wayis the air flowing?arrow_forwardSteam flows through a nozzle at 400 °C and 1 MPa (h= 263.9 kJ/kg) with velocity of 300 m/s. Find the stagnation enthalpy.arrow_forwardThe refrigerant R134a is passing through the diffuser with the inlet diameter of D1=1 inch; p1=150psi; and V1=1000 ft/s as a saturated vapor. The exit parameters are p2=400 psi, and velocity V2=0.5 ft/s. Heat transfer, Work, and Potential energy changes can be neglected. NOTE: Use English units. For the kinetic energy change do not forget dividing to (778*32.2) conversion factor to obtain Btu/lbm. From NIST tables use BTU/lbm units for the enthalpy. Determine: a.Exit temperature in F; b.Mass flow rate in lbm/s; c.Exit diameter D2 in inches. d.Determine exit temperature. show and expalin each step pleasearrow_forward
- A gas at upstream conditions is throttled to a downstream pressure of 1.2 bar. Estimate the downstream temperature and the change in entropy of the gas for the following: Nitric Oxide, with T1 = 300 K and P1 = 70 baarrow_forwardA stream of air at 77°F and 1.2 atm absolute flowing at a rate of 225 ft3/h is blown through ducts that pass through the interior of a large industrial motor. The air emerges at 500°F. Calculate the rate atwhich the air is removing heat generated by the motor. What assumption have you made about the pressure dependence of the specific enthalpy of air?arrow_forwardAir enters a frictionless duct with V₁ = 70 m/s, T₁ = 600 K, and P₁ = 350 kPa. Letting the exit temperature T₂ vary from 600 to 5000 K, evaluate the entropy change at intervals of 200 K, and plot the Rayleigh line on a T-s diagram.arrow_forward
- Q4. A constant-area duct, 25 cm in length by 1.3 cm in diameter, is connected to an air reservoir through a converging nozzle, as shown in Figure. For a constant reservoir pressure of 1 MPa and constant reservoir 1 MPa temperature of 600 K, determine the flow rate through the 600 K duct and the back pressure. Assume a choked adiabatic flow in the duct, with f = 0.023. Figure Q4arrow_forwardAir at 27 °C and 100 kPa enters in a steady flow to a nozzle at a velocity of 100 m/s. If the inlet area of the nozzle is 0.5 m², what is the mass flow rate through the system?arrow_forward(b) Air flows through a cylindrical duct at a rate of 2.3 kg/s. Friction between air and the duct and friction within air can be neglected. The diameter of the duct is 10cm and the air temperature and pressure at the inlet are T₁ 450 K and P₁ = 200 kPa. If the Mach number at the exit is Ma2 determine the rate of heat transfer and the pressure difference across the duct. The constant pressure specific heat of air is cp = 1.005 kJ/kg-K. The gas constant of air is R = 0.287 kJ/kg-K and assume k = 1.4. -arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY