Show that the equation can be reduced to h 1 + V 1 2 2 = h 2 + V 2 2 2 = constant .

Question

Want to see the full answer?

Answer 1

Question

Chapter 12, Problem 39P

(a)

To determine

Show that the equation can be reduced to h1+V122=h2+V222= constant .

(b)

To determine

Show that for adiabatic flow of an ideal gas with friction T0T=1+(k−12)M2.

(c)

To determine

For this flow does T01=T02? and p01=p02? Explain these results.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

Find the specific volume and enthalpy of steam at 8 bar when the condition of steam is (i) Wet with dryness fraction 0.6 (ii) Dry saturated Absolute Temp. Specific enthalpy (kJ/kgi Specific entropy (kJ[kg K) Specific volume (m/kg) pressure ("C) (bar) 7.0 165.0 697.1 2 064.9 2 762.0 1.991 8 4.7134 6.7052 0.001108 0.273 7.2 166.1 702.0 2061.1 2 763.2 2.003 1 4.6925 6.6956 0.001110 0.265 7.4 167.2 706.9 2057.4 2 764.3 2.014 1 4.672 1 6.686 2 0.001111 0.258 7.6 168.3 711.7 2 053.7 2765.4 2.024 9 4.6522 6.677 1 0.001112 0.252 7.8 169.4 716.3 2 050.1 2 766.4 2.035 4 4.632 8 6.668 3 0.001114 0.246 8.0 170.4 720.9 2046.5 2 767.5 2.045 7 4.6139 6.659 6 0.001115 0.240 8.2 171.4 725.4 2043.0 2 768.5 2.055 8 4.595 3 6.6511 0.001116 0.235 8.4 172.4 729.9 2 039.6 2 769.4 2.065 7 4.577 2 6.6429 0.001118 0.229 8.6 173.4 734.2 2 036.2 2770.4 2.0753 4.559 4 6.634 8 0.001119 0.224 8.8 174.4 738.5 2 032.8 2771.3 2.084 8 4.542 1 6.6269 0.001120 0.219 9.0 175.4 742.6 2 029.5 2772.1 2.094 1 4.5250 6.6192…

Steam flows through a nozzle at mass flow rate of m = 0.1 kg/s with a heat loss of 5 kW. The enthalpies at inlet and exit are 2500 kJ/kg and 2350 kJ/kg, respectively. Assuming negligible velocity at inlet (C₁0), the velocity (C₂) of steam (in m/s) at the nozzle exit is (correct to two decimal places) Q = 5 kW h₁ = 2500 kJ/kg C₁=0 m= 0.1 kg/s h₂ = 2350 kJ/kg C₂ 28/45

Where necessary, assume air as an ideal gas and consider R = 287J/(kg.K), Cp = 1005 J/(kg.K), Cv = 718 J/(kg.K). A nozzle is a device that is used to increase the velocity of a fluid by varying the cross-sectional area. At the last section of a jet engine (Fig Q1.a, section 5), air with a mass flow rate of 50 kg/s at a pressure of 500 kPa and a temperature of 600 K enters a nozzle with an inlet cross-sectional area of 5 m2. The exit area of the nozzle is 20% of its inlet area. The air leaves the nozzle at a velocity of 300 m/s. The nozzle is not well-insulated and duringthis process, 5 kJ/kg heat is lost. (i) In analysing this nozzle using the 1st law of thermodynamics,the change in which type of energy is negligible? (ii) Determine the density and velocity of the air entering thenozzle. (iii) Calculate the density of the air as it leaves the nozzle.