A piece of steel wire 100 feet long, with a cross-sectional area of 0.004 aq. in., must be stretched with a pull of 16 pounds when in use . if the modulus of elacticity of steel is 30,000 psi: a) what is the total elognation in the entire length of the wire? b) what tensile stress is producted by the pull?

A piece of steel wire 100 feet long, with a cross-sectional area of 0.004 aq. in., must be stretched with a pull of 16 pounds when in use . if the modulus of elacticity of steel is 30,000 psi: a) what is the total elognation in the entire length of the wire? b) what tensile stress is producted by the pull?

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2DP

See similar textbooks

Similar questions

The modulus of elasticity of mild steel is equal to .. .? .... .. a. 2 x 10ʻN/m? a. 2 x 10'N/m 2 b. 2 x 10° N/m 4 c. 2 x 10 N/mm 5 d. 2 x 10 N/mm Check
} 8) A tensile load of 3000 N is applied to a steel bar of cross-sectional area 500 mm?. If a tensile load was applied to an aluminum bar to achieve the same lateral (transvers) strain with the former (steel bar), what would be the load? Note: Original dimensions of the two bars are the same (Est = 2.1 x 105 MPa, Eat = 0.703 × 105 MPa, vg = 0.3, vat = 0.33) E = º , v = - Saterat Eaxial Fatuminum™ 3000 N A-500 mm² A=500 mm² Fatuminum=? 3000 N Steel Aluminum
2.) Answer the following: a.) a 22 ft long solid steel rod is subjected to a load of 15,000 lb. This load causes the rod to stretch 0.435 in. The modulus of elasticity of the steel is 30,000,000 psi. Determine the diameter of the rod. b.) A solid circular titanium control rod must support an axial tension force of 12,000 lb. Assume that the modulus of elasticity of the titanium in 16,500,000 psi. If the rod must elongate no further than 0.35 in. when the normal stress of the rod is 68,000 psi, determine the minimum rod diameter AND the maximum rod length.
A 10 inch long silver wire is stretched to a total length of 11.50 inches. Find the value of strain
A drill rod with a diameter of 1/2 in. is made of high-strength steel alloy with a shear modulus of 11.6 * 106 psi. The rod is to be subjected to a torque T.What is the minimum required length L of the rod so that the cross section at one end can be rotated 60° with respect to the other end without exceeding an allowable shear stress of 45 * 103 psi?
What is the value of reduction factor of the beam, if the stress in the steel is 400 MPa, and the Modulus of Elasticity of the Steel is 200,000 MPa. O 0.671 0.692 O 0.660 O 0.650 None of the Choices O 0.681
Example: tension test has been conducted on a specimen of steel (Lo=100 mm, Do-20mm) and the following results have been obtained: 375 7500 750 850 1100 1200 1250 1150 1000 Load Fractur (kgr) Extensio 0.06 0.12 1.40 4.00 12.00 18.00 24.00 29.00 32.00 e n (mm) 1. Draw engineering stress-strain curve. 2. Draw true stress-strain curve on the same plot for comparison. 3. Calculate yield strength. 4. Calculate tensile strength. 5. Calculate percent elongation at fracture. 6. Calculate ductility by two methods. 7. Calculate modulus of elasticity.
1. For the 15 foot copper bar shown in the figure below, find the total elongation (or shrinkage). The bar has a square cross section of 2" x 2" ( 16,000 lbs 4000 lbs 12' Punch Force 12000 lbs 2. A metal plate is 125 inch thick. What force is required to punch out a square piece 1" x 1"? The ultimate shear stress of the metal is 37,000 psi, and the ultimate tensile stress is 60,000 psi.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress (in Mpa) in the steel given that P= 96.3 kN? Express your answer in two decimal places.
Q- A cylindrical piece of steel, with a diameter of 60mm and length 100 mm, is subjected to an axial compressive force of 40,000 kg. If bulk modulus is 1.7 x 106 kg/cm² and poisson's ratio is 0.25 than the change in volume of the cylindrical piece is
A 15" long rod, pinned at both ends, with radius of 1/2 ", made from 6061 T6 Aluminum is subjected to a compressive axial load of 10 Kips. Question 4 of 6: What is the axial strain in the rod? ( in percent) O .0013 O .13 O 1.3 O 13
An alloy steel having a diameter of 0.45 in. extends 0.002 in. over a gage length of 2.2 in. due to a tensile load of 3900 lb. What is the modulus of elasticity of this alloy steel? A)29,010 ksi B)27,000 ksi C)30,000 ksi D)28,000 ksi