When applying the general method of calculation for a dwelling unit, what is the feeder and service demand load, in kW, for one (1) 8kW rated residential electric range? 17. A. 8.0 kW B. 6.4 kW C. 7.0 kW D. 12.0 kW

When applying the general method of calculation for a dwelling unit, what is the feeder and service demand load, in kW, for one (1) 8kW rated residential electric range? 17. A. 8.0 kW B. 6.4 kW C. 7.0 kW D. 12.0 kW

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter29: Service-entrance Calculations

Section: Chapter Questions

Problem 2R: a. What is the unit load per ft2 for the general lighting load of a residence? ____ b. What are the...

See similar textbooks

Related questions

Q: Considering an average load for the 5 machines is 211 KW and the total connected load is 302 KW,…

A: Plant load factor depends on the average load and maximum demand. Demand factor depends on the the…

Q: A steam power station spends 83916 OMR per annum for coal used in the station. The coal has a…

Q: Example 3. A steam power station spends Rs. 30 lakhs per annum for coal used in the station. The…

A: In this question we need to find a average load on the station.

Q: Find the total annual charge on an installation costing Rs. 500,000 to buy and install, the…

A: Given, As scrap value is negligible so, Q = P ∵Q=P-scrap value Installation costing, P = Q =…

Q: The annual fixed costs for a plant are $100,000, and the variable costs are $140,000 at 70%…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: A consumer has a maximum demand of 100 MW at 60% load factor. If the tariff is 2 OMR per kW of…

A: The solution is attached below for given problem.

Q: hydroelectric generating station is supplied from a reservoir of capacity 8 × 106 cubic meters at a…

Q: An air conditioning unit has a cooling capacity of 24,000 Btu/hr. If the unit has a rated…

A: Given values are – Cooling capacity (P) = 24000Btu/hour EER = 11 Power charge = 14cents/Kwh =…

Q: 4. Daily load of an industry is 200 kW for first one hour, 150 kW for next seven hours, 50 kW for…

A: energy consumed = power * time in hours annual bill =cost on energy consumed plus cost on maximum…

Q: A plant erected to manufactured socks has a first cost of P10, 000,000 with an estimated Salvage…

A: 1. Given that: First cost (FC) = P10,000,000 Salvage value (SV) = P100,000 n = 25 years…

Q: A diesel engine power plant has one 700 kW and two 500 kW generating units. The fuel consumption is…

A: Calculate the maximum energy, Maximum energy = (700+500+500) ×24 ×30…

Q: A Hydroelectric Plant has a Turbine and Generator with an efficiency of 63%. If the dam has a Head…

A: To find the power generated in the hydroelectric power plant First convert all data in SI Unit

Q: Assume that these are all the appliances that you have in your house. If the cost of your…

Q: what is the minimum neutral demand load in (kw) for 12 apartments, each containing an 8-kw range

A: Given that, For 1 apartment = 8 kw Given that for 12 apartments.

Q: Use the table below to calculate the Apartment's Energy Consumption for each day

A: It is required to calculate total energy consumption in kWh for given loads. Note: Except…

Q: d) In a month of March, a private house used approximately 27.5 kWh per day. Calculate the total…

Q: Find the wind speed in K/h needed to generate 4641.7Kw for a wind turbine with a height of 32.13m…

A: Given data, Power generated P = 4641.7 KW Height h = 32.13 m Density ρ=6.125 kg5 m3=1.225 kg/m3,

Q: A thermal station has an efficiency of 15% and 0.9 kg of coal burnt for every kWh generated.…

A: Consider that 1 kWh is equal to 860 kCal

Q: Determine the complex power absorbed by the voltage source

A: In this question, Determine the complex power absorbed by the voltage source? Complex power S= VI*…

Q: consumer is using 250 units per month. If he is charged at a block rate tariff of 20 baisa for the…

Q: A consumer has a maximum demand of 200 kW at 40% load factor. If the tariff is Rs. 100 per kW of…

A: We have an demand of consumer and we have been asked to find the cost per KWh for this given data.…

Q: An industry consumes the following daily loads: 200 kW for first two hours, 300 kW for next eight…

A: The solution can be achieved as follows.

Q: on of the Tariff characteristics is to be fair by charging the big consumer a high rate than the…

A: The first question is subjective and hence out of scope. The solution for rest two questions is as…

Q: Q5// The power generation equipment of a power station cust Rs 15,75,000 and has a useful life of 25…

A: Sinking fund method is used to determine the depreciation costGiven DataP = 1575000S = 75000Interese…

Q: 13.12 An air-conditioning unit has a cooling capacity of 24,000 Btu/h. If the unit has a rated…

A: Given:

Q: 1. Power companies typically bill customers based on the number of kilowatt-hours sed during a…

A: A kilowatt is known as the power which is consumed by an electric appliance—it's 1,000 watts to be…

Q: A building has 3 floors and each floor has 4 fans of 50 W that operates for 12 hours a day and one…

A: Given, A building has 3 floors and each floor has 4 fans of 50 W that operates for 12 hours a day…

Q: An industry daily load is 259 kW for first 2 hours, 103 kW for next 8 hours, 159kW for next 6 hours,…

A: Total expenditure per year = rate of maximum * maximum demand + Rate per KWH*Total units consumed in…

Q: 8. Calculate the electric bill of a residential apartment for the month 'July 2020' considering the…

A: Total consumed unit=464 units (Kw-hr) The per-unit rate will be 8.70 BDT The total cost will be,…

Q: Given the latent heat of melting ice 334 kj/kg., and density 0.86 kg/dm, Determine the power of…

Q: A power supplies 520 kW [note units] of power to a factory through wires with a transmission…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: B) The probability that it is Friday and that a student is absent is 0.03. Since there are 5 school…

A: The probability that it is Friday and that a student is absent = 0.03 The probability that it is…

Q: Which of the following equipment should be installed by the consumers having low power factor

A: Equipment used by consumers to improve the power factor is :-

Q: A hydro station of 3 MW generate 358 Mwh for one week. If the water discharge at one week is 542000…

A: Given Power capacity of hydro station P = 3 MW Total generation in one week E= 358 MWh Water…

Q: Given the two loads with the power rating: a.) Incandescent light bulb = 100 W b.) LED lamp = 9 W…

A: Given, Two loads are Incandescent light bulb power rating (P1)=100W per hour LED lamp power rating…

Q: Atmospheric air is blowing at 55 km per hour in a windy province in Mindanao. A windturbine…

A: V=55km/hr=15.27m/secDiameter=20mPower generated=235.04 KW

Q: Tenaga Nasional Berhad (TNB), the electric company in Peninsular Malaysia charges its domestic…

A: In this question we need to find a how much the household pays per month on PC and the refrigerator.

Q: A single-story house has average kilowatt-hour consumption per month is 4.75 kWh/m2/day. How many…

A: Given: Consumption of electricity=4.75 kWhm2×daywattage of solar panel=250 WDerate Factor=85% Step…

Q: g period. Peak demand is typically measured at 400 kW during the day and 200 kW at night. However,…

A: Service charge for 3 phase is P518. Energy Charge , Total Energy consumed = 126000kWh total energy…

Q: 1. The boiler, turbine, alternator efficiencies of a thermal power plant are 35%, 86% and 93%…

A: Given: ηboiler=35% or .35ηturbine=86% or .86ηalternator=93% or .93Value of heatind coal=12000…

Q: Assuming that the Philippines is consuming 3.5×10^20 kWh of electrical energy in one year and the…

A: Most of human energy requirement is meet by generating electrical energy. Once electrical energy is…

Q: A consumer has annual consumption 7,00,800 units. If his maximum demand is 200 kW. The load factor…

A: Given, A consumer has annual consumption 7,00,800 units. Maximum demand is 200 kW

Q: Assuming that a country is consuming 3.5×10^20 kWh of electrical energy in one year and the power…

A: A power plant is an industrial facility that uses primary energy to create electricity. To deliver…

Q: A consumer is using 250 units per month. If he is charged at a block rate tariff of 15 baisa for the…

A: consumer is using 250 units per month. He is charged at a block rate tariff of 15 baisa for the…

Q: Given two loads with the following ratings: CRT TV Set: 190 W LCD TV Set: 96 W Compute the monthly…

A: Given data, Rating of CRT TV set is 190 W. Rating of LCD TV is 86 W. Cost is given 11.25 Rs / kWh

Q: The amplitude of the voltage available in the 60-Hz, 230-V power outlet in your home is what? A.…

A: In this we will find The amplitude of the voltage available in the 60-Hz, 230-V power outlet in…

Q: Q3: Calculate the average power in kW that can be generated in a hydro- electric project from the…

A: In this question ,we have to find average power in KW that can be generated in a hydro electric…

Q: A small manufacturing plant on a single three-phase service consumes 126,000 kWh of electrical…

A: For the small manufacturing plant-The total consumed electrical energy = 126000kWhThe peak demand…

Q: .The original cost of a certain piece of equipment is P150,000 and it is epreciated by 10% sinking…

A: Given that Orginal cost ofequipment=P150000depreciated i=10%=10100=0.1%n=10 yearyearly…

Q: A power transmission line carries 525 A of current at a voltage of 944 kV. If the line has a…

A: Given a power transmission line having, Current, I = 525 A Voltage, V = 944 kV Line has resistance,…

Concept explainers

Photoelectric

The photoelectric effect occurs when light (or similar incident radiation, including X-rays) falls on material together with a metal plate and causes it to emit electrons. The discovery of the photoelectric effect led to important new theories (and to a Nobel Prize for Albert Einstein). Photoelectric cells, or photocells, are utilized in burglar-alarm light detectors and garage-door openers (each employs a through-beam of light this is broken when something movements throughout it), and also to play soundtracks on film movies (in which a light beam shines through the soundtrack encoded at the film and is "read" with the aid of the photocells).

Question

17.
When applying the general method of calculation for a dwelling unit, what is the feeder and
service demand load, in kW, for one (1) 8kW rated residential electric range?
A.
8.0 kW
B.
6.4 kW
C.
7.0 kW
D.
12.0 kW

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Calculation of feeder and service demand

VIEW

Step 2 continued...

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Discuss the concept of a smart grid and how it improves the efficiency and reliability of power systems.
In a string of suspension insulator with three units,the line unit has 12k and k=0.15. The voltage across string is and the efficiency is .?: a. 41.6kV & 69.4kV b. 33.62kV & 74.7% C. 29.52kV & 82% d. 36.9kV & 82%
Advantages of using per unit system in power system studies is O a. None of these O b. Both more informative and calculations are easy. O c. More informative O d. Calculations are easy
The levelised cost of electricity (LCOE) is often used to compare the costs of electricity production from different types of electricity generation plant. Carefully describe the significance of the LCOE and give one advantage and one disadvantage of using this metric to compare plants.
Explain the concept of a smart grid and how it can improve the efficiency and reliability of power systems.
A housing estate is being built and the electrical system for each house from a range of 2 to 20-bedroom houses from single floor apartments to 3 storey buildings are on offer throughout the estate. There are commercial buildings to be constructed for shopping purposes as well. What risks exist and what are the components and methods we use to mitigate these risks both at the substation and at the consumer/ residential side. Describe how these would all fit together.
Question 5 It is desired to have a maximum power transfer from an amplifier to the load of the system. The resistance in the amplifier and the voltage are 120 Ohms 160 volts respectively. Twice the turns of the wires on the conductor at the secondary side of the transformer and the turns of the wire at the primary side of the transformer is 35. The impedance at the load is 53.33 ohms. If the difference of the turns of the wire at the primary side of the transformer and primary side of the transformer is 5. Answer the following questions below: a. What is the maximum power transfer from the generator to the load? b. Show that the transformer assisted in transferring maximum power from the generator to the load. c. What is the power transfer from the generator to the load when there is no transformer between the amplifier and the load
Which of the following statements regarding the cost structure of a wind farm are true? Select one or more: a. The turbine accounts for 40% of the total cost of an onshore wind farm. O b. About half of the total cost of an offshore wind farm consists of foundation, substation and cabling costs. c. Almost half of the total cost of a wind turbine is made up of the cost of a tower and blades.
Explain the concept of "smart grids" and how they contribute to the efficiency and reliability of power systems.
Briefly explain the functions of smart grid.
Cost of a 600 kW wind turbine is $ 550000. Other initial costs including that for installation and grid integration are 30 per cent of the turbine cost. Useful life of the system is 20 years. Annual O&M costs plus the land rent come to 3.5 per cent of the turbine cost. Calculate the cost of generating electricity from the turbine when it is installed at a site having a capacity factor of 0.25. The real rate of interest may be taken as 5 %.
Explain the concept of FACTS (Flexible AC Transmission Systems) devices in power systems. How do they enhance the controllability and stability of electrical grids? Provide examples of FACTS devices.