1.8 A motor drive is supplied from a three-phase power converter has conversion efficiency of 90 % when operating at rated load. On the other hand, when the motor operates at rated load, it delivered net output power of 45 kW. The motor electrical and mechanical losses are 1125 W and 1200W respectively. Calculate the efficiency of the system from supply utility to motor shaft. [Ans: 85.5%]

1.8 A motor drive is supplied from a three-phase power converter has conversion efficiency of 90 % when operating at rated load. On the other hand, when the motor operates at rated load, it delivered net output power of 45 kW. The motor electrical and mechanical losses are 1125 W and 1200W respectively. Calculate the efficiency of the system from supply utility to motor shaft. [Ans: 85.5%]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Two 50-MVA, 3-phase alternators operate in parallel. The settings of the governors are such that the rise in speed from full-load to no-load is 2 percent in one machine and 3 percent in the other, the characteristics being straight lines in both cases. If each machine is fully loaded when the total load is 100 MW, what would be the load on each machine when the total load is 60 MW? (Req'd) Draw an appropriate diagram.
EX3 Voltage Sag 400 V network short circuit power is 1000 kVA (reactive). A 10 kW induction motor is connected. The motor takes 6-times nominal current when started (assume inductive current). Calculate the voltage drop as a) per unit value, b) per cent value, c) volts in line voltage, d) volts in phase voltage.
Two 60MVA, alternators operate in parallel. The setting of the governor are such that the rise in speed from full load to no load is 2% in one machine and 3% in the other, the characteristics being straight lines in both cases. If each machine is fully loaded when the total load is 120MW, what will be the load on the first machine (with 2% speed regulation) when the total load is reduced to 80MW?
A) An equalizer is a jumper used to parallel the series field of two compound DC generators when the two generators are being run in parallel to share an electrical load. a) true b) false B) The ohmic value of an equalizer is not important as long as it is made out of copper. a) true b) false C) How is the efficiency usually expressed?a) in watts b) in kilowatt-hours c) in percentage d) none of the above
A 25 kVA, 2 kV(rms)/100 V(rms) single phase transformer is connected between a 120 V(rms) utility supply and a resistive load. The load current was measured to be 20 A(rms). i. Determine the active power of the load. ii. Determine the primary RMS current. iii. Determine the equivalent resistance of the transformer as seen by the utility supply.
Two 220V generators operate in parallel. One machine has a terminal voltage of 270 V on no-load and 220 V when supplying 35 A. The second machine has a voltage of 280 V on no-load and 220 V when supplying 50 A. Calculate: (i) the output voltage; and (ii) current of each machine when total current is 60 A. Assume the external characteristics to be linear.
4. A 2 MVA, 2.3kV, three-phase Wye connected alternator operates at rated kVA at a power factor of 80 %. The dc armature winding resistance between terminals is 0.08-ohm. The field takes 70-A at 125-V from the exciter equipment. Friction and windage loss is 20-kW, iron loss 36-kW and stray power loss are 2.0-kW. Calculate the efficiency of the alternator. Assume the effective armature winding resistance is 120% of the dc resistance.
Alternator A (100 kVA, 3-f, 240 V, 60 Hz, 1800 rpm) is operating in parallel with alternator B (125 kVA, 3-f, 240 V, 60 Hz, 1800 rpm). The load of alternator A is 70 kW at 85% pf leading and the load of alternator B is 85 kW at 75% pf leading. Determine the pf of load.
1.List the three steps of nuclear fuel fabrication processes. Also sketch a schematic diagram and label the processes on the diagram. 2 What is geothermal energy? With the aid of a schematic diagram, describe how we can generate electricity using a geothermal energy-driven dry steam power plant. 3.Discuss the differences between Pelton, Francis, and Kaplan turbines.
1. A resistor, in series with a 138-microfarad capacitor, is connected to a 60-cycle source. If the voltage drop across the capacitor is 115 volts and the power taken by the circuit is 922 watts, calculate (a) the circuit current, (b) the ohmic value of the resistor, (c) the line voltage, (d) the circuit power factor. Please show complete solution and the circuit diagram. Please round off answers up to the 3rd decimal place. Thank you!
3. Two de generators each having linear characteristics that operate in parallel. One machine has a terminal voltage of 470V at no load and 220 V at a load current of 100A. while the other machine has a voltage of 480 V at no load and 200 V at 120 A. calculate the current in each generator and the bus bar voltage when the total load is 200A. What is the kilowatt output of each machine under this condition?
A 20 kVA machine has a full load copper loss of 400 W, an iron loss of 150 W, and a mechanical loss of 200 W. Determine:a) Efficiency at 3/4 of full load with f.d.p. 0.8. Ans: 95,43%b) Performance at full load with f.d.p. 0.9. Ans: 96%c) Peak performance apparent power. Ans: 18,71 kVAd) Yield in the previous case for f.d.p. Unit. Ans: 96,39% I need the procedures to get these results. Thanks