What are the contents of the file registers WREG, 0x010, 0x020, 0x410, 0x420, after the following program is executed? Assume that all the register contents are initially zero.
Q: 1. The bit sequence 1101 is serially entered (right-most bit first) into a 4-bit parallel out shift…
A: [1] Consider a four bit shift register Q3 Q2 Q1 Q0 Given, Initially the register is clear, Q3 =0, Q2…
Q: What is the MUX1 select input while the "sltu" instruction is executing? 01 00 10…
A: Answer - C - 10
Q: After execution the short label jump instruction: JMP 84h; (when updated IP =A4h), the new value of…
A: JMP instruction is a short jump instruction. It is used to jump within the range of +127 to -128.
Q: What is the maximum memory size that can be connected to a processor with a lower order address bus…
A: In this question we will find maximum memory size that can be connected to a processor...
Q: 7. What type of register can have a complete binary number loaded into it in one operation, and then…
A: Note as there are several questions and we are asked to solve one question at a time. So do mention…
Q: DISCUSSION: 1- Determine the logic required to decode the binary number 1011, by producing a HIGH…
A:
Q: Assume the register pair HL contains the value 1234H. What does it contain after executing the…
A:
Q: Using four cascaded counters with total 16 output bits, how many states must be deleted to acheive a…
A: The counter under consideration has a total of 16 output bits. For a counter having v output bits,…
Q: The address bus of a computer is 16 bits wide and the data bus is 32 bits wide. How many bytes does…
A: Given data, The address bus line of a computer is 16 bits. The data bus line of the computer is 32…
Q: Let (BX)=100H, DI=200H, DS=1200H, SI= FOO2H, AX= 0105H, and the following memory content.what is the…
A:
Q: 1- Discus the results in all steps. 2 - What is the variation in the address decoder circuit if its…
A: what is the variation of address decoder circuit if it deals with memory what is the variation of…
Q: Show the status of PSW (Program status word) after addition of two 8bit numbers 26H and 3FH. Also…
A: As per Bartleby guidelines we are allowed to solve only one question, please ask the rest again. The…
Q: b) The number of addressed words in a ROM is determined from some fact. 92 × 8 ROM architecture…
A: According to the question, The number of address words in a ROM is determined by some fact. 92 X 8…
Q: Load the number of ffh into the 'a' register and write the code that reduces the number in the 'a'…
A: Load the number of ffh into the 'a' register and write the code that reduces the number in the 'a'…
Q: 2 (a) Determine the control word ICW2 require for PIC controller so that IRQ0 to IRQ7 correspond…
A: PIC is Programmable interrupt controller This helps a microprocessor to handle interrupt requests…
Q: Look at the following parts of the program PROCESS (enable) BEGIN IF (enable'EVENT AND enable = '1')…
A: Because of process statement , statements written below process will execute only when variable…
Q: 5. What is the file extension is used to load in a microcontroller to execute an instruction? • .doc…
A: We are authorized to answer one question at a time, since you have not mentioned which question you…
Q: Q. 1 There are different types of memories used in 8086 microprocessor one of them is called Stack.…
A:
Q: 1) Assume the signals with the highest amplitude of 5 volt are transmitted. The max error is about 1…
A: The solution is given below
Q: If R0 = 0x20008000, after run STMDB r0!, {r3, r9, r7, r1, r2} command what is the r7 register memory…
A: According to the question, we need to find the memory start address for the resister r7.
Q: : Design 4-bits shift register with two control inputs A and B the register operate according to the…
A: Multiplexer is a combinational circuit with multiple inputs and single output. It has select inputs…
Q: Refer to the following registers values and memory snippet to answer the following questions.…
A: The 8086 microprocessor is a 16 bit microprocessor with 16 data lines and 20 address lines. It is…
Q: Write the contents of the first two addresses of ram in two lines after running the given code.
A: According to the question, we need to find the contents of the first two addresses of ram in two…
Q: If Timer 0 Register TMR0L is initialized with -1 in 8-bit mode, then after how many clock cycles…
A: Timer 0 has two register 1) TMR0L= Timer 0 Low 2) TMR0H= Timer 0 High after starting timer…
Q: 3. Consider a 24-bit system. To represent the system, a) How many bytes are required? b) How many…
A: 3) Given: A 24-bit system a) no of bytes required b) no of nibbles required c) no of digits…
Q: 1) The control flags type and operation? 2) Compare between CS & CX registers? 3) Assume SS=5000H,…
A: Flag registor of 8086 microprocessorControl flags - the control flags enable or disable certain…
Q: After executing XLAT instruction, the content of system registers is: ES=4E25,, DS=041C, DI=6814…
A: According to the question, we need to find the content of AL before the execution of the XLAT
Q: Explain what the stack pointer register is and what it does in a few words.
A:
Q: An AVR has 0XFFF as the address of its last byte in the RAM and it has the same value OXFFF as the…
A: The memories have the same number of locations since the address bus has 12 bits. We can store each…
Q: What other options are there besides OUTPUT for the pinmode instruction?
A: The pinMode function can have other functionality besides declaring output, there are: 1- For…
Q: SV What is clocking block ? what is program block?
A: Reg is driven by always block it can't be driven by continuous assignment statement. Always block…
Q: Question 1 (a) Sketch and describe the programming model of the 68k MPU. (b) At one given fime, how…
A: Solution (a) - The 68k MPU's programming model is also known as the Instruction Set Architecture.…
Q: Look at the following parts of the program PROCESS (enable) BEGIN IF (enable'EVENT AND enable - '1')…
A: Because of statement Process (enable) statement written below this will execute only whenever enable…
Q: In the MIPS processor that is part of the PIC32 microcontroller, what is the length of each…
A: MIPS stands for Microprocessor without Interlocked Pipelined Stages. MIPS processor is a part of the…
Q: Consider multi-level page table with 22-bit memory addresses and 1 KB page size. The size of the…
A: According to the question, Consider a multi-level page table with 22-bit memory addresses and 1 KB…
Q: a) Discuss different methods of moving a content from R2 to R1 register. Assume that Register Bank O…
A: 1. MOV (Move) transfers a byte, word, or doubleword from the source operand to the destination…
Q: Q3: The original contents of CX, AX, memory location Beta, and carry flag (CF) are FFE116 11AB16,…
A:
Q: You want the instruction OUT AL, 25 to activate the LS373 latch. Which control signal on our MCS…
A: We canthe instruction OUT,AL,25 to activate LS373 latch. which control signal must be connected with…
Q: Consider the following instruction mix of the LEGV8 assembly code: R-type I-type LDUR STUR CBZ B 24%…
A: We are authorized to answer one question at a time, since you have not mentioned which question you…
Q: There are different types of memories used in 8086 microprocessor one of them is called Stack. You…
A: As per our policy i have attempted first three sub-part only. (i) In stack memory the allocation…
Q: Question: Assume a system comprises 16 GB physical memory with B KB page/frame sie and the…
A: Virtual memory is a volatile memory . it store the temporary data . virtual memory used both the…
Q: What is the bit storage capacity of a ROM with a 512 × 8 organization? List the types of read-only…
A: Registers are sequential circuit used to store binary information. Semiconductor memory are use for…
Q: Suppose some hypothetical system’s control unit has a ring (cycle) counter consisting of some number…
A: The maximum number of micro-operations is given. Hence, the timing signals per clock tick is 10. The…
Q: 1- Identify the addressing mode for: MOV CX, [1234] 2-The instruction that subtracts 1 from the…
A: In this 1st question , we have to determine addressing mode ...and in 2nd question , we have to find…
Q: 2- The instruction that adds immediate datalcontents of memory location specified in an…
A: There are different type of addressing modes available in the microprocessor 1. immediate 2. Direct…
Q: Suppose that the Program Counter, register R15, contained the hex valu Ox8000. From what address…
A: A Cortex-M3 CPU is developed for large, reduced-cost platforms in a wide range of applications, such…
Q: 1. What is the difference between nonvolatile and volatile memory? 2. Do you expect the monitor…
A: As per our policy I have to do the first one only. Non-Volatile Memory It is that type of memory in…
Q: Draw the logic diagram of a fiveObit register with five D flipOflops and five 4 x 1 multiplexers…
A:
What are the contents of the file registers WREG, 0x010, 0x020, 0x410, 0x420, after the
following program is executed? Assume that all the register contents are initially zero.
Step by step
Solved in 2 steps
- The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True FalseAssume that [SP]= 01FF. Then Consider the following program: PSH X PHSY PSHA PULA i) ii) Show the contents of the stack after each instruction What are the contents of the stack register at the end of the execution of the above instructions?Question 1: Use Indirect addressing to write a PIC24 assembly code that complements and adds 5 and multiply by 2 to 1024 data bytes into the memory at starting address Ox1000. The original data are stored in the memory starting from address 0x800. it is an electrical engineering question . this is the full information about the question!
- . (A-)Hand trace the execution of the following program fragments showing what happens to the flags and registers (AL, BL, CL) in each statement supposes that the flags are initially 0. MOV BL, 03H CF SF ZF OF PF AF ADD BL, 02H SUB BL, 05H MOV AL, 00H DEC AL XCHG AL, BL6- Set BX to 4567H, CX to FEDCH and SP to A59FH, then run the instructions: PUSH BX PUSH CX a. What is the new value of SP ? b. Display the memory locations where you pushed the values of BX and CX in the stack.1. Assume that the registers are 8-bit wide. Consider the following code: MOV R1, #4A MOV R2, #40 ADD R3, R1, R2 a) What will be the 8-bit result in Register R3 (in hex)? b) What is the 8-bit result in Register R3 (as unsigned decimal)? c) What is the 8-bit result in Register R3 (as signed decimal)? d) What will be the value of the carry (C) bit?
- Mention the addressing mode, function and how many bytes instruction for the following instructions? a. ADI 42H b. LXI H, 2500H c. RLCWrite a program to PUSH R0, R1, and R3 of Bank 0 onto the stack and POP them back into R5, R6, and R7 of Bank 3. Also, mention the value of SP register after every PUSH and POP operation. this question is asked in microprocessor and microcontroller3. Suppose r0=0x20000000 and r1=0x12345678. All bytes in memory are initialized to 0x00. Suppose the following assembly program has run successfully (the three instructions will be executed in the given order). Draw a table to show the memory value if the processor uses little endian. STR r1, [r0], #4 STR r1, [r0,#4]! STR r1, [r0, # 4] Address 0x20000010 0x2000000f 0x2000000e 0x2000000d 0x2000000c 0x2000000b 0x2000000a 0x20000009 0x20000008 0x20000007 0x20000006 0x20000005 0x20000004 0x20000003 0x20000002 0x20000001 0x20000000 Data
- After executing XLAT instruction, the content of system registers is: ES=4E25, DS=041C DI=6814, BX=0201, and AL =40, (all values shown are in hexadecimal and the addresses shown are physical addresses). What is the content of AL before executing this instruction? H. H. Address 20н 40 H 60 н 80 H A0H СОн E0 H Content 447C 447D 447E 447F 4480 4481 4482 Notes: 1- Use the memory fragment shown to answer this question. 2- Write down the final value of AL as two hexadecimal digits without any additional characters.Given the memory content below, fill in the table below with the register values after the execution of 3 instructions starting at instruction at address 589. Consider the initial values PC=589 and AC=0006. (all values are in Hexadecimal). address Content 13C 025A 25A 0231 589 113C 58A 7200 58B 7020 Note that you need to fill 4 digits for AC, 3 for PC, and 1 for E. AC (in Hex)= EEBE PC (in Hex)= 58C E=An 8051 subroutine is shown below: SUB: RO, #20H @RO , #0 MOV LOOP: MOV INC RO CJNE RO, #80H, LOOP RET a. What does this subroutine do? b. In how many machine cycles does each instruction execute? How many bytes long is each instruction? C. d. Convert the subroutine to machine language. e. How long does this' subroutine take to execute? (Assume 12 M