Look at the following parts of the program PROCESS (enable) BEGIN IF (enable'EVENT AND enable = '1') THEN CASE STATE IS i) Does the process of count up and count down counter values depend on the enable variable or not? Explain! In such programs, the counter works synchronously or asynchronously? Explain! ii) If it depends on the enable variable, does the program work in a rising edge or falling edge? Fynlain!

Look at the following parts of the program PROCESS (enable) BEGIN IF (enable'EVENT AND enable = '1') THEN CASE STATE IS i) Does the process of count up and count down counter values depend on the enable variable or not? Explain! In such programs, the counter works synchronously or asynchronously? Explain! ii) If it depends on the enable variable, does the program work in a rising edge or falling edge? Fynlain!

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Supnorting.cxcentions &interruats Select True/False (T/F) for each statement. Exception usually refers to an event outside of the CPU and interrupt refers to an event inside the CPU. ISelect The CPU checks for exceptions/interrupts after every assembly instruction to get to them tast. Select With polled interrupts, the hardware is responsible to identify the source of the event. Select) With vectored interrupts, the hardware is responsible to identify the source of the event. I Setect)
8085 microprocessor went through its manipulation operation in the ALU, the results was transferred on the data bus and status of the results was stored in the flag register for indications . With your knowledge and understanding illustrate a complete bit configuration of 8085 flag register and show the functions of the represented bits in the register.
1. Write the contents of all registers and the conditions codes registers after each execution instructions in Table Q1(a). Instructions SUBS r0, rl, 12 MOV 12,13, ASR #3 ro 11223344 Table Q1 (a) rl F7770025 12 r3 CF119856 CF119856 NZ V C 010 1
Design a three bit synchronous binary counter that counts two by two with T-flipflops,continously. Output should be one when the counter equals maximum number.a. Draw the exitation table b. Draw the corresponding state diagram. c. Tabulate the state table for the sequential circuit. d. Draw the logic diagram of the circuit.
Overflow flag bit indicates overflow for a.Signed integer only. c. Signed and Unsigned integer only. The 8086 architecture consists pipeline processing. b. Two b. Three arithmetic operations. b. Unsigned integer only. d. Floating point. unit(s) work in parallel is called c.Four d.One
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
7.a. Weight and humidity are examples ofA. discrete outputs.B. discrete inputs.C. voltage signals.D. analog quantities. 7.b. What statement best describes the CPU scan?A. The data table is read, the inputs are updated, and the logic is solved.B. The fault table is cleared, the inputs are read, and the outputs are updated.C. The program scans for a "logic OK"; if the bit is set, the scan progresses.D. The input status is read, the program logic is solved, and the outputs are updated.
Electrical Engineering Design a three input NOR layout so that rise time and fall time become equal when input logic switches from (111) to (000) and again to (111)? 10
Write a Verilog code with testbench for 16-bit up/down counter with synchronous reset and synchronous up/down.If up/down is set the counter is up counter and if it is not set, the counter is a down counter. submit the module code, testbench code, and the simulation results. PLEASE EXECUTE CODE IN VERILOG
Q5: Fill in the following blanks with appropriate answers (Choose Five Only) 1. The instruction that subtracts 1 from the contents of the specified register/memory location is ..…….….…..………………….. 2. In general, the destination operand of an instruction can be ....... 3. The instruction that supports addition when carry exists is 4. If there is a carry from lowest nibble during addition, ............. flag sets. 5. register is used as a default counter in case of string and loop instructions. 6. In PUSH instruction, after each execution of the instruction, the stack pointer is. ************** **********
P Flag question Explain the MUL instruction of 8086. Compare it with IMUL instruction. (1 +1 Marks) Write a Assembly language program for 8086 to find the cube of a number using MUL instruction. (5 Marks) (Note : Solve the question in paper, scan and upload along with the other Part B and C answers) B I III
If R0 = 0x20008000, after run STMDB r0!, {r3, r9, r7, r1, r2} command what is the r7 register memory start address?A. R0= 0x20007ff4B. R0 = 0x20007ffefC. R0 = 0x20007fffD. R0=0x20007fecE. R0 = 0x20007ff0