Consider multi-level page table with 22-bit memory addresses and 1 KB page size. The size of the entire page table will be ---------- (in decimal) bytes. Given a virtual address 1111000110000101001101 (in binary), the page directory index will be ----------- (in binary), and the page table index will be ----------(in binary).

Consider multi-level page table with 22-bit memory addresses and 1 KB page size. The size of the entire page table will be ---------- (in decimal) bytes. Given a virtual address 1111000110000101001101 (in binary), the page directory index will be ----------- (in binary), and the page table index will be ----------(in binary).

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Q3) A - Convert the Excess-3 to binary number : ( 110001011100.10001010)ex-3 B- convert each Gray code to binary: 1-( 011010001001)G 2-(59)D
Explain the arithmetic operations in binary number system and how code conversion is done between binary and decimal numbers.
Convert the following values to a 4-byte memory map assuming each is stored as an int : (a)(1AEEF5AA)base16 Byte Address In decimal Byte Value in hex (b)(1010100100010100001100011100110)base2 Byte Address In decimal Byte Value in hex (c)1073750032)base10 Byte Address In decimal Byte Value in hex
question1:In a memory system, data is 16-bit wide. Break the information into bytes with their addresses using little endian and big-endian methods. Starting address is F800 and the data is: E0F2 0041 question2:What acknowledgment signals are there in I2C bus?
Q2) convert the following: 1- decimal number to binary by using the repeated division by 2 method (49) 2- binary number to hexadecimal (10101010)( 3- octal number to decimal by repeated division by 8 method (254)() 4- BCD code numbers to decimal (100101111000)>() 5- Gray code to binary (1010)(
3- what is the advantages of memory segment. 4- state the purposes of segment registér. 5- what is the different between general purpose register and segment register and flag register.
Assume that memory location $c100 holds a data byte =$37, [ACCA]= $B8 and [ACCB]=$FE. For each of the following instructions determine the resultant content of ACCA or ACCB. (a) ANDA $C100 (b) ANDA #$05 ORAB #$EE (c) (d) CLR B (e) NEGA (f) DECB (g) ASLA (h) LSRB (i) EORA #$E4 (G) ROR A
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
............ signal must be low to access data on the odd addressed memory bank a. BHE and A0 b. BHE c. A0 d. M!IO
the diagram on the right is for a register bank circuit that contain 8 registers. Each register is 16-bit. Theregister can read or write to one register at a time using address bus.Design the circuit and specify the width of EVERY bus.
c) Given a 32K x 8 RAM chips. Compute: i) the number of chips needed to build a 128K byte memory using 32K x 8 RAM. ii) the number of address lines that must be used to access the memory. iii) the number of lines connected to the address inputs of each chip, the number of lines to be used for chip select inputs and type of decoder to be used. iv) Determine the range of addresses for the 128K byte memory.
5. Write an assembly language program to convert an 8-bit binary data to BCD. The binary data is stored in 4200H. Store the hundred's digit in 4251H. store the ten's and unit's digits in 4250H