After executing XLAT instruction, the content of system registers is: ES=4E25, DS=041C DI=6814,BX=0201, and AL =40, (all values shown are in hexadecimal and the addresses shown are physicaladdresses). What is the content of AL before executing this instruction?H.H.Address20н40 H60 н80 HA0HСОнE0 HContent447C447D447E447F448044814482Notes:1- Use the memory fragment shown to answer this question.2- Write down the final value of AL as two hexadecimal digits without any additional characters.

According to the question, we need to find the content of AL before the execution of the XLAT

After executing XLAT instruction, the content of system registers is: ES=4E25,, DS=041C, DI=6814 BX=0201, and AL =40, (all values shown are in hexadecimal and the addresses shown are physical addresses). What is the content of AL before executing this instruction? H' H' H. Address Content 20H 40 H 60 H 80 H АОн CO H E0 H 447C 447D 447E 447F 4480 4481 4482

After executing XLAT instruction, the content of system registers is: ES=4E25,, DS=041C, DI=6814 BX=0201, and AL =40, (all values shown are in hexadecimal and the addresses shown are physical addresses). What is the content of AL before executing this instruction? H' H' H. Address Content 20H 40 H 60 H 80 H АОн CO H E0 H 447C 447D 447E 447F 4480 4481 4482

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Solve the following question. You must show your work. a) What does 962F000016 represent in an IEEE single-precision floating-point number? b) Convert -151o to a 16-bit sign-magnitude representation. c) Convert-151o to a 16-bit two's complement representation. d) Define the system status register value after an instruction execution resulted the following: a. Result was a non-zero value, a negative value, had a carry and extended bits. b. Trace mode was not on and was executed in supervisor mode. C. Any higher interrupt priorities higher than level 3 will be recognized.
1. Write the contents of all registers and the conditions codes registers after each execution instructions in Table Q1(a). Instructions SUBS r0, rl, 12 MOV 12,13, ASR #3 ro 11223344 Table Q1 (a) rl F7770025 12 r3 CF119856 CF119856 NZ V C 010 1
1. An 8-bit register contains the number 10000110. The serial number 11011011is applied to the input. After 5 shift pulses, what is the number in the shift register? Assume shift right operation 2. A binary number is shifted 5 positions to the left. The number therefore has been 3. A binary number must be divided by 128. How many positions must the number be shifted (and in what direction to achieve this?
An 8051 subroutine is shown below: SUB: RO, #20H @RO , #0 MOV LOOP: MOV INC RO CJNE RO, #80H, LOOP RET a. What does this subroutine do? b. In how many machine cycles does each instruction execute? How many bytes long is each instruction? C. d. Convert the subroutine to machine language. e. How long does this' subroutine take to execute? (Assume 12 M
the diagram on the right is for a register bank circuit that contain 8 registers. Each register is 16-bit. Theregister can read or write to one register at a time using address bus.Design the circuit and specify the width of EVERY bus.
Given the memory content below, fill in the table below with the register values after the execution of 3 instructions starting at instruction at address 589. Consider the initial values PC=589 and AC=0006. (all values are in Hexadecimal). address Content 13C 025A 25A 0231 589 113C 58A 7200 58B 7020 Note that you need to fill 4 digits for AC, 3 for PC, and 1 for E. AC (in Hex)= EEBE PC (in Hex)= 58C E=
3. Suppose r0=0x20000000 and r1=0x12345678. All bytes in memory are initialized to 0x00. Suppose the following assembly program has run successfully (the three instructions will be executed in the given order). Draw a table to show the memory value if the processor uses little endian. STR r1, [r0], #4 STR r1, [r0,#4]! STR r1, [r0, # 4] Address 0x20000010 0x2000000f 0x2000000e 0x2000000d 0x2000000c 0x2000000b 0x2000000a 0x20000009 0x20000008 0x20000007 0x20000006 0x20000005 0x20000004 0x20000003 0x20000002 0x20000001 0x20000000 Data
Q1. Design a circuit of General register organization in which 4 registers are there from R0 to R3. (a) Explain the control word as per the register configuration given above.
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Write a program to add the following five data bytes stored in memory locations starting from XX60H, and display the sum. (The sum does not generate a carry. Use register pair DE as a memory pointer to transfer a byte from memory into a register.) Make a flow chart for the same. Data(H) 1A, 32, 4F, 12, 27
Write a program in assembly language to toggle PORTB 400 times. Use BNZ instruction.
- The stack memory is addressed by a combination of the plus offset. The PUSH and POP instructions always transfer between segment -bit number the stack and a register or memory location in the 8086 microprocessors. For string instructions, DI always addresses data in the segment. The 8086 LOOP instruction decrements register for a 0 to decide if a jump occurs and tests it