We have a load with an impedance given by Z= 30+j40 Ω.The voltage across this load is V = 15002 ∠30° V.Is the load inductive or capacitive? Determine the power factor, power, reactive power, and apparent power delivered to the load.

We have a load with an impedance given by Z= 30+j40 Ω.The voltage across this load is V = 15002 ∠30° V.Is the load inductive or capacitive? Determine the power factor, power, reactive power, and apparent power delivered to the load.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Related questions

Q: Find the total impedance ZT in polar form b. Draw the impedance diagram c. Find the current I and…

Q: For the circuit shown, Z, = 50 – j30 N. What component is needed to form impedance ZPFC in parallel…

A: Power Factor Correction is a method that uses capacitors to minimize the reactive power component of…

Q: Determine if a load (impedance) is capacitive or inductive, given the following 4 cases: a. pf =…

A: Given: Consider the following cases: a. pf = 0.87, leadingb. pf = 0.42, leadingc. v(t) = 42 cos(ωt)…

Q: The voltage across a load is v(t)=1042 cos(ωt+10°) V, and the current through the load is i(t) = 202…

A: Given: voltage across the load is, v(t)= 1042cos(ωt+10°) V Voltage across the load…

Q: The circuit with 3 parallel loads is explained as follows. Load1 = draws 8 kW average power and the…

Q: 3. Refer to the circuit shown C 120V, 60HZ Z = 10+j12 2 (a)What is the power factor? (b) What is the…

Q: For the circuit shown, what is the complex power, S, consumed by the load impedance? (Assume the…

A: The complex power is given by: S=VI*where,I* is conjugate of current I. Given: Vs=150∠0°R=15ΩC=150…

Q: Find the load impedance ZL for the circuit that will result in maximum average power being…

A: The given circuit is shown below: The Thevenin impedance of the circuit is,…

Q: Perform phasor analysis to the circuit shown to evaluate the total complex power (S) absorbed by the…

A: In this question, we need to determine the across the load 40+30j i. average power (P), ii. reactive…

Q: 111.803 L- 41.57° V. (i) Determine the value of impedance Za. UTM UTMD Determine the complex power,…

Q: A load consisting of a 1.35 kO resistor in parallel with a 405 mH inductor is connected across the…

A: In this question, We need to determine the average active power, reactive power ,apparent power and…

Q: The load impedance ZL for the circuit shown is adjusted until maximum average power is delivered to…

A: (A) The maximum average power to the load ZL, when ZL is adjustable is: Where, The magnitude of the…

Q: For the circuit shown, ZL = 21 – j45 2. What component is needed to form impedance ZpFc in parallel…

Q: Problem #2: For the circuit below, i, (t) = 5 cos 10t A. a) Use Phasor Analysis and obtain the…

Q: If a current of I = 30 cos(1000t + 60°) mA was found to be flowing through an impedance found…

A: according to the ohm's law if the impedance is Z and current i I then value of the votlage is given…

Q: Three branches having impedances of 3+j4 Ω, 16−j12 Ω, and−j4 Ω, respectively, are connected in…

A: Given data: Impedance Z1 = 3+j4 Ω Impedance Z2 = 16-j12 Ω Impedance Z3 = -j4 Ω The admittance of the…

Q: (a) A load has impedance, Z = (50 + j14) N. Convert this value of Z into polar form, |Z|40, where Z…

Q: The characteristic impedance of a losseless transmission line is 60N. Find the inductance of the…

A: DISTORTION-LESS LINE: A line in which a wave propagates without any distortion is called a…

Q: 19.22 72mH V, Z V, -

A: we need to find out phasor V1 . Given:: the load is connected to 100V (rms) and dissipates 1kW at…

Q: For the circuit shown, determine: a) The impedances Z1 and Z2 in polar form b) The combined total…

A: We represent the given circuit in phasor domain.

Q: For the circuit shown, ZL = 50 – j30 N. What component is needed to form impedance ZPFC in parallel…

A: Given V=55∠0° Vf=110 HzZL=50-j30 Ω Calculating admittance of the given circuit…

Q: = 2. Express y - ₁ + y₂ as a single sinusoidal function if y₁ and Y₂ = 40 cos(wt+ 60°) A) Solve by…

Q: 1. The single phase ac voltage source is v = 141.4cos(377t)V, the load can be modeled as a 16mH…

A: In the question, Voltage given v=141.1cos(377t)V Resistance R=8 ohm inductance L= 16mH…

Q: Unless given, use the: POLAR FORM for voltage and current, RECTANGULAR FORM for impedance. Consider…

Q: Problem #2: For the circuit below, i, (t) = 5 cos 10t A. a) Use Phasor Analysis and obtain the…

Q: For a circuit with the below rms voltage source and impedance: V1 = 115 20° V Z = 65 – j 23…

Q: The Thevenin impedance of a source is ZTh = 120+ j 590, while the Thevenin voltage is VTh=327 + j265…

A: Maximum power: It states that maximum power transfer only possible when the load resistance is equal…

Q: Consider a load that has an impedance given by Z=100-j50 Ω. The current flowing through this load is…

A: Given data, The value of impedance is Z = 100-j50 Ω. The value of load current is I = 152 ∠30° A.…

Q: Unless given, use the: POLAR FORM for voltage and current, RECTANGULAR FORM for impedance. Consider…

Q: total impedance [ZT] in polar form,

A: Given-E= 100∠0o VR= 8 ohmXL=6 ohm

Q: a. Vrms = 120445°,Z = 35 +30j Determine the Real Power, Reactive Power, Complex Power, Apparent…

A: This question belongs to basic electrical . It is about calculation of different types of power when…

Q: 1 In the circuit of Figure. Z, = 60Z– 30°N · and· Z, = 40Z45°Q. %3D (1)-Find the phasors İ,,İ‚‚İ¸.…

A: Given circuit,

Q: etermine the steady-state expression for the source voltage V(t) in rcuit shown below, if the load…

Q: For the circuit shown, ZL = 50+ j30 2. What component is needed to form impedance Zprc in parallel…

Q: = The Thevenin impedance of a source is ZTh 89+ j 68, while the Thevenin voltage is VTh = 346 + j373…

Q: H.W.: A 440 V rms source supplies power to a load ZL = 10 + j2 Q through a transmission line having…

A: As per the guidelines of Bartley we supposed to answer first three subpart only.

Q: Problem 1: Given v(t)=70.71 sin (@t+45°) and i(t)=28.28 cos(mt-15") ; determine the following a)…

A: Given : The supply voltage v(t)=70.71 sin (wt+45°) The supply current i(t)=28.28 cos(wt-15°)…

Q: j1 N 2 Vx ト10 |ZL 4/0° A Vx 310 Şekil 3

A: First we will find out thevenin equivalent circuit across load impedance then from maximum power…

Q: Unless given, use the: POLAR FORM for voltage and current, RECTANGULAR FORM for impedance. Consider…

Q: 5Ω j3 N a 20 /0° 20 ΩΣ -j6 Ω V b (a) For the circuit shown above, determine the impedance Zı that…

Q: The power consumed by ZL = (145-J22) Q impedance connected to the ab terminals in the given circuit…

A: For calculation of the Thevenin voltage the circuit is: Applying Nodal Analysis at Node A,…

Q: H.W.: Given the phasor voltage V = 115V245 V across an impedance Z = 16.2619.3 Q, obtain an…

A: Given, V=1152∠45°Z=16.26∠19.3°ω=50 rad/s

Q: Find the load impedance ZL for the circuit that will result in maximum average power being…

A: In this question we need to find a load impedance for maximum average power transfer to load

Q: For the following voltage and current phasors, calculate the complex power, apparent power, real…

Q: For the circuit shown, Z parallel with Z, such that the load achieves unity power factor? = 50 – j30…

Q: Find the RMS line voltage VL at the source of the circuit. As shown the RMS load phase voltage is…

A: You have the solution nicely. But there is a slight mistake in the calculation at the last step of…

Q: Can anyone help? This is an old exam and is answered (wrong might I add) and I need help.

A: For the circuit to achieve unity power factor, it must be at resonant.From the circuit,

Q: Unless given, use the: POLAR FORM for voltage and current, RECTANGULAR FORM for impedance. Consider…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: shown below, de following: a) The impedance Zi that results in maximum average power transferred to…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sinusoids and Phasors of Alternating Circuit

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The phasor voltage across a certain load is V=10002 ∠30° V, and the phasor current through it is I=152 ∠60° A. Determine the power factor, power, reactive power, apparent power, and impedance. Is the power factor leading or lagging?
For a capacitive load: a) Investigate the complex power in terms of real power, reactive power, and power factor. b) Draw the phasor diagram c) Investigate the possibility of correcting the load power factor in details. Show diagrams, circuits, equations, etc.
The voltage across a load is Vt : 104/2 cos(wt +75°), and the current through the load is ¡(t) = 2/2 cos(wt + 30°). The reference direction for the current points into the positive reference for the voltage. Determine the complex power and if this load is inductive or capacitive? S = 14140 + jl14140 Inductive S = 40000Z45° %3D Сараcitive S = 2000Z105° Сараcitive S = 5000 – j5000 Inductive
Calculate the capacitance that when placed in parallel with the load, will raise the power factor to unity. Please answer in typing format please ASAP for the like Please
If, in one (360 degrees), all of the instantaneous power falls under positive loops (no negativeloops), the load must be:a. A resistorb. An inductor or capacitorExplain:
An electric load consists of a resistor, a capacitor and an inductor connected in series. The total impedance of the load is connected across 240430° V, compute the following: a. The load impedance b. The source current in polar form c. The phase shift between the current and the voltage d. The power factor of the load e. The real power of the circuit f. The reactive power of the circuit 20 mH 50UF 240430° 314rad/s W =
d. 565.685 V If a Load absorbs 20 kVA at a leading power factor of 0.6. Then the complex power is: Select one: O a. 12000 - j16000 VA O b.-12000 + j16000 VA O c. 12000 + j16000 VA O d. None of these Given the circuit below and the associated set of voltages and currents, the reactive Power developed by im voltage source is FENG300 MINTERM
a. Find the total admittance and impedance in polar form b. Draw the admittance and impedance diagram c. Find the voltage E and currents IR , IL , and Ic in phasor form d. Draw the phasor diagram of the currents Is, IR, IL and IC, and the voltage E. e. Verify Kirchhoff’s current law at one node f. Find the average power delivered to the circuit g. Find the power factor of the circuit, and indicate whether it is leading or lagging. h. What happened if R= 10 Ω
A load has a leading power factor. a) Is it a capacitive or inductive load? b) Is the reactive power positive or negative? c) Repeat for a load with lagging power factor
What is the power factor of a load with complex power S = 1000 + j250 KVA? what kind of load is it? Resistive, capacitive, inductive, or conductive?
For the system in the figure: Find the total average power, total reactive power, total apparent power, and total power factor. Find the current Is (in phasor form). If the loads can be modeled as a resistance in series with a reactive element (capacitor or inductor), find the impedance of each load. Confirm the result of part B using the input voltage and the result of part C. ..
Q3 (a) In Figure Q3(a), the load impedance, Zi is adjusted until it absorbs the maximum average power. (i) Determine ZL (ii) Determine the maximum average power, Pmax -j42 j10 2 elll 4) 6 A ZL Figure Q3(a) ww ww