For the circuit shown, ZL = 50- j30 N.What component isneeded to form impedance ZpFo in parallel with ZL such that%3Dthe load achieves unity power factor?5520° VZPFCf = 110 Hz

Given V=55∠0° Vf=110 HzZL=50-j30 Ω Calculating admittance of the given circuit…

Answered: For the circuit shown, ZL = 50 – j30 N.…

For the circuit shown, ZL = 50 – j30 N. What component is needed to form impedance ZPFC in parallel with ZL such that %3D - the load achieves unity power factor? 5520° V ZL ZPFC f = 110 Hz

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Related questions

Q: Calculate the Apparent power (complex in VA), real power (real part in W) and reactive power…

A: Let the current flowing through 40 Ω from top node to bottom node is I1 and the current…

Q: QI: Draw the impedance diagram for the series R-C circuit for the figure, then find the : Q2: For…

Q: The load ZL consumes an average power of 75 W and a reactive power of 125 VAR. What component is…

Q: The load impedance ZL in the circuit is adjusted until maximum average power is transferred to ZL.1.…

A: (1) The load impedance with reference to primary side (Z’L) of the transformer is: By applying…

Q: Source: Ean = 12020° v; Epn = 1204 – 120° v; Een = 1204120° v (grounded neutral) Zan = Zpn = Zen =…

A: Given Condition : Without fault

Q: The impedance ZL in the circuit is adjusted for maximum average power transfer to ZL. The internal…

Q: Three branches having impedances of Z1, Z2, and Z3 0, respectively, are connected in parallel. TI…

Q: For maximum average power transfer in the circuit shown in the figure, set the impedance ZL and ZL…

A: In the circuit, For maximum average power transfer in the circuit shown in the figure, impedance…

Q: (d) Figure Q1(d) shows an AC circuit. Given Vị = 24 - 15° V (i) Determine the value of impedance Zr.…

A: The solution is given below

Q: Find the phasor voltage ?s (rms) if loads ?1 and ?2 are absorbing 15 ??? at 0.6pf lagging and 6???…

A: For Load 1 :kVA rating=15 kVAp.f. cosϕ=0.6 laggingSo, complex power will be :S1=15cosϕ+j15…

Q: The load impedance ZL for the circuit shown is adjusted until maximum average power is delivered to…

A: (A) The maximum average power to the load ZL, when ZL is adjustable is: Where, The magnitude of the…

Q: The 9 Ω resistor in the circuit is replaced with a variable impedance Zo. Assume Zo is adjusted for…

Q: Given that a nonzero AC voltage source is applied, what can you say about whether the power,…

A: Lagging power factor is when the current lags behind the voltage. In this case, the circuit is…

Q: Find the impedance ZL and the value of the maximum average power transferred to ZL for the maximum…

A: 4=Voc1-j1 Voc =4-j4 v

Q: (a) A load has impedance, Z = (50 + j14) N. Convert this value of Z into polar form, |Z|40, where Z…

Q: Q2. A series of motor (Load 1) and lighting (load 2) are connected to an AC source as shown in…

Q: The load Z, consumes an average power of 75 W and a reactive power of -125 V AR. What component is…

A: Given Data: P = 75 W Q = -125 VAR vs = 75 w = 250

Q: Derive an expression for V(rms)» fundamental and harmonic components of the load voltage as a…

Q: The magnitude of the load voltage in the circuit shown in Figure 1 is [Vrms| = 470V and radian…

A: For given frequency

Q: Q2. A series of motor (Load 1) and lighting (load 2) are connected to an AC source as shown in…

A: The solution is given below

Q: In the circuit below Z1 = 40/-60° and Z2 60/40° 2. Calculate: a) The currents I1, l2 and Is b) The…

A: Note: As per guidelines will be solving only the first 3 subparts. Please repost for others…

Q: For the circuit shown, ZL = 21 - j45 N. What component is needed to form impedance ZpFc in parallel…

Q: Q2. A series of motor (Load 1) and lighting (load 2) are connected to an AC source as shown in…

Q: The load Z, consumes an average power of 75 W and a reactive power of 125 VAR. What component is…

Q: (a). Write the instantaneous currents across the three circuit elements in terms of Vm amp > angular…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: (b) A 12V 200, 2kHz AC voltage source of 5002 output impedance is connected to a load of impedance…

A: A voltage is being applied across a series of two resistors via a voltage divider. As the current…

Q: In the circuit below Z1 = 40/-60° N and Z2 = 6040° Q. Calculate: %3D %3! a) The currents I1, l2 and…

A: In this question we will find current in each branch, total current , total complex power and active…

Q: The impedance of zl for the maximum average power transfer in the circuit shown in Figure 3 and ZL…

Q: total impedance [ZT] in polar form,

A: Given-E= 100∠0o VR= 8 ohmXL=6 ohm

Q: a. Vrms = 120445°,Z = 35 +30j Determine the Real Power, Reactive Power, Complex Power, Apparent…

A: This question belongs to basic electrical . It is about calculation of different types of power when…

Q: Q2. A series of motor (Load 1) and lighting (load 2) are connected to an AC source as shown in…

Q: Q2. A series of motor (Load 1) and lighting (load 2) are connected to an AC source as show in Figure…

Q: A small industrial plant has a 12-kW heating load and a 25-kVA inductive load due to a bank of…

Q: Q2. A series of motor (Load 1) and lighting (load 2) are connected to an AC source as shown in…

A: In this question, we need to determine the total impedance, current I, frequency domain waveform…

Q: In the circuit shown in Figure 4, the load voltage is Vrms 156020°. Notice that Vrms = | Vrms | =…

Q: Determine the impedance, Z2, that will result in the total impedance shown in figure below. Z2 ZT =…

A: If n number of resistor having resistance R1,R2.....................Rn is connected in series then…

Q: j1 N 2 Vx ト10 |ZL 4/0° A Vx 310 Şekil 3

A: First we will find out thevenin equivalent circuit across load impedance then from maximum power…

Q: A delta-connected impedance is given by Za = Determine Za in both Cartesian and polar form given z,…

Q: P 11.5-14 The source voltage in the circuit shown in Figure P 11.5-14 is Vs = 24 /30° V.…

Q: Q2: For the circuit in the figure, find: 16mH 265LF R=42 + UR - + PL + vc e= 70.7 sin 377) a) Find…

A: Voltages and current of the given circuit are calculated as shown below

Q: For the single-phase voltage controller the source is 120 V rms at 60 Hz, and the load is a series…

Q: Two impedances, Z1 = 2+j6 N and Z2 = 6-j12 are connected in series with a 220-V 60-Hz supply. At…

Q: P5.94. A delta-connected source delivers power to a delta-connected load, as shown in Figure P5.94.…

Q: Calculate the impedance ZL for the maximum average power transfer in the circuit shown in Figure 3.…

Q: The load ZL consumes an average power of 75 W and a reactive power of -125 VAR. What component is…

Q: Can anyone help? This is an old exam and is answered (wrong might I add) and I need help.

A: For the circuit to achieve unity power factor, it must be at resonant.From the circuit,

Q: Find the total impedance of the circuit, total power (apparent) delivered by the current source,…

Q: Find the total impedance, voltage drop on the 100-ohm resistor, draw the phasor diagram of the…

A: Current and voltage always in phase incase of resistance Current lag by 90 degree with respect to…

Question

For the circuit shown, ZL = 50- j30 N.What component is
needed to form impedance ZpFo in parallel with ZL such that
%3D
the load achieves unity power factor?
5520° V
ZPFC
f = 110 Hz

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sinusoids and Phasors of Alternating Circuit

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms
The output voltage waveform of a four quadrant chopper is shown in figure. In the waveform, Vdc is input voltage, D is duty cycle ratio and T is cycle time. DT T. The RMS value of ripple component in output voltage is (A) Vác 2V VD-D (В) V(2D-1) (C) de de (D) V de VD- D? yd
Exercise-1 Vs = 240V 60Hz Is=10A/....... Power system Is ww R 1k0 Xc=-j/(2pi60x0.00016)=-1994 XL=ZL=j2pifl=j2pi60x0.142=j53.54 142mH Is=Ir+IL+Ic=.........=Vs/Ztotal=....... 160μF
An impedance load consisting of 12 ohms resistance and 16 ohms inductance reactance is connected across a 50 Hz, 100 V source. Find the capacitance of the condenser which may be paralleled with this load to bring the power factor to 0.80 leading.
Draw the sinusoidal waveform of the AC voltage and current for the given loads below. Describe the characteristics of the waveform for each load. A. Pure resistor B. Pure inductor C. Pure capacitor
What impedance vector - j25 represents:A. A pure resistance. C. A pure capacitance.B. A pure inductance. D. An inductance combined with a resistance.
2.14 The current waveforms of la capocitov are avesage peak cursend *atings of 1, =500 A of shown in Fiquse Determine square (rms), and capacitor. Assume, The root mean half sine -wave t = loo us -300 AS t3 Soo Ns f, -250HZ T2 200
Two lossy capacitors with Equal capacitance values and power factors of 0.01 and 0.02 are in parallel, and the combination is supplied from a sinusoidal voltage source. The power factor of the combination is ?
15. You are working on a power factor correction installation, and you notice with a clip-on ammeter as you add in capacitance the current drops, you add more capacitance and the current drops, you add more capacitance the current rises. How do you know when you are at unity power factor?
A DC-DC Chopper Circuit with an RL Load has an output current waveform shown below with a duty cycle of 50% and 1ms period. If it has a resistance of 1ohm and an inductance of 10mH, find the source voltage. 5A 2A ton toff output _current
A single-phase AC voltage controller has a resistive load R = 10 Ohm, and the RMS input voltage is Vs = 230 V, 60 Hz. The delay angle is 120 degree. Then power factor of the circuit is: Select one: O a. 1 O b. 0.75 O c. 0.44 O d. None of the above O e. 0.9
What is the average power in ghe single phase ac circuit with the purely resistive load? It is sinusoidal steady state excitation.