A piping system is to be installed at place where the pump will transfer the fluid from tank A totank B. There are two suggested piping designs available to carry the fluid efficiently. Computeand determine which of the available piping arrangement will experience the less pumping powerwith given flow conditions. Discuss the results.Design 1:Tank B60 m8 cm I8 cmPipe exit40 mSharp bendPumpTank ADia - 5 cm18 cmPipe inletSudden expansion15 m Design 2:|Tank B30m10 am10 omPipe exit40mSharp bendTank ADia-5 om10 cmPipe inletSudden expansion30 m20 mFlow conditions are same for both type of designs and given as:Page 3 of 4Pipe material: stainless steelVolume flow rate: 40 L/secAssume the working fluid is water at standard atmosphere temperature and both tanks areopen to atmosphere.Pipe inlet is sharp-edged and bends are sharped without vanes.· Elevations are as Z1=20 m and Zz= 90 m

Answered: Image /qna-images/answer/96fe653a-7ddf-4394-8d96-3429bfb3939b.jpg

A piping system is to be installed at place where the pump will transfer the fluid from tank A to tank B. There are two suggested piping designs available to carry the fluid efficiently. Compute and determine which of the available piping arrangement will experience the less pumping power with given flow conditions. Discuss the results. Design 1: Tank B 60 m 8 cm I 8 cm Pipe exit 40 m Sharp bend Pum z, Tank A Dia - 5 cm Pipe inlet Sudden expansion tsm 15 m

A piping system is to be installed at place where the pump will transfer the fluid from tank A to tank B. There are two suggested piping designs available to carry the fluid efficiently. Compute and determine which of the available piping arrangement will experience the less pumping power with given flow conditions. Discuss the results. Design 1: Tank B 60 m 8 cm I 8 cm Pipe exit 40 m Sharp bend Pum z, Tank A Dia - 5 cm Pipe inlet Sudden expansion tsm 15 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A submersible pump is to be selected for the installation on a newly drilled deep well. The static water level (SWL) of the water inside the well is 8.7m from the natural ground level and the centerline of the discharge pipeline is 3.5 feet above the natural ground level. Based on the test pumping results from the SWL the flow velocity at the pipeline discharge was 8.09 ft/s and the design pressure is 40 psi to assure that the water can reach the elevated water tank. The total head losses are assumed to be 12 feet. a.) Find the total dynamic head (TDH) of the submersible pump needed for sizing in feet ? b.) What will be the suitable pipe diameter for the system riser in inches?
Show complete solution and formulas used. Show the schematic diagram too. Calculate the required pipe diameter to avoid cavitation, if the pump delivers Q = 30US gallon/min water from a closed tank, where the pressure (above the water level) is p = 40kPa. The equivalent length of the smoothened concrete pipe on the suction side is 12m while the suction flange of the pump is 8m below the water level. The vapour pressure at the given water temperature is 2.8kPa. The required net positive suction head is NPSHr = 3.2m.
The below figure shows a pump that transfers a steady stream of 35◦API crude oil from an oiltanker to a refinery storage tank, both free surfaces being open to the atmosphere. Theeffective length—including fittings—of the commercial steel pipe is 6,000 ft. The dischargeat point 4 is 200 ft above the pump exit, which is level with the free surface of oil in thetanker. However, because of an intervening hill, point 3 is at a higher altitude than point 4.Losses between points 1 and 2 may be ignored.The crude oil has the following properties:Density ρ = 53 lbm/ft 3 ; Viscosity μ = 13.2 cP; Vapour Pressure Pv = 4.0 psia Answer the following questions:1. If the combination of pump and motor is 80% efficient, how much electrical power(kW) is needed to drive the pump?2. If, in order to avoid vapour lock, the pressure in the pipeline must always be above thevapor pressure of the crude oil, what is the maximum permissible elevation of point 3relative to point 4?3. If the flow in the pipeline…
A centrifugal pump having a head-capacityrelationship given by the equation ha=180 –6.10 X 10-4 Q2, with ha in feet when Q is ingpm, is to be used with the system shownin the figure, For Z2-Z1= 50 ft, what is theexpected flowrate if the total length ofconstant diameter pipe is 600 ft and thefluid is water? Assume the pipe diameter tobe 4 inch and the friction factor to be equalto 0.02. Neglect all minor losses.
-Example the values. asystem total head. against for the initial condition, show below - give the Lallowiny data dynamic uiscosity of liquid Calculate capacity curve density S-1200 kgim3 Static head on Suction Side 7S-3m Static heac on discharge Side Zd= 7m inside diameter of pipe di = o.052m -pipe roughress E3D0.00045m. gas pressure aboue the liquid in the tank Side of the pump the Suction Ps= atmospheric pressure. gas pressure above the liquicd in the tank on discharge side of the pump. the dund Pd= atmesperic pressure
1 QUESTION 1 Consider a desired pump operating condition which adds 35 psi at a flowrate of 500 gpm to water (p= 62 11m/ft²³) Ignore any changes in Kinetic or potential energy and Tassume isothermal flow C.e. internal energy is constant, this is the normal assumption we make when analyzing fluid flows in piping systems). Apply the energy balance only across the pump with full energy Balance and simlifying to solve for the pump, Starting head symbolically. Then begin careful of units, Solve for pump head in feet. GIVEN: 35psi 500 gpm p=62 1bm/3 XA. 10.5 A B. 100.8 ft C. 50.1 ft D. 80.7f 35 500 62 (32.2) + 2(32.2) 35 + 500
For the hydraulic system of Figure, the following data are given: The pump is adding2.984kW to the fluid.(a) Pump flow is 0.00158 m3. (b) The pipe inside diameter is 0.01905m.(c) The specific gravity of the oil is 0.9.(d) The oil tank is vented to the atmosphere.(e) The head loss HL between station 1 and 2 is 12.19m.(f) The elevation difference between stations 1 and 2 is 6.096m.Find the pressure available at the inlet to the hydraulic motor(station 2).
Prob-2 HL=8.5 m Compute discharge pressure of Pump: Elevation=50m Psuction =-40Kpag Pdischarge = Elevation=80m H₂O
The 11-in Bell and Gossett pump is tobe scaled up to provide, at best efficiency, ahead of 250 ftand a flow rate of 3000 gal/min. Find the appropriate(a) impeller diameter; (b) speed in r/min; and (c) horsepowerrequired.
Saturated water at 310K is being pumped from a tank to an elevated tank at the rate of 7L/s. All of the piping is in 5-in. schedule 40 steel pipe. If the 2 fittings used is 90° ell standard long radius, The pump has an efficiency of 80%. Calculate the kW power needed for the pump. * 125 m 12 m -5 1 50 m 5-in. pipe schedule pump Your answer
m². -5 S Figure shows a portion of a fire protection system in which a pump draws water at 60°F (v =1.21 ×10¯ from a reservoir and delivers it to a point B at the flow rate of 1500 gal/min. Calculate the required height h of the water level in the tank in order to maintain 5.0 Psig pressure at point A h 25 ft A Pump 2600-ft-long 8-in Schedule 40 steel pipe Flow Flow 45-ft-long 10-in Schedule 40 steel pipe B
It is desired to deliver 4 gpm at a head of 670 m in a single pump having specific speed not to exceed 40. If the operating speed is not to exceed 1352 rpm, how many stages are required? Select the correct response: 0 7 O 5 3 6 Contin 2.