03: There are three connected pipes (38 m length of 5 cm pipe diameter),. (23 m length of 15 em pipe diameter) and (46 m length of 7.5 cm pipe diameter), all of them made of cast iron, as shown in Figure 2. There are three 90° elbows and an open globe valve, all flanged. If the exit elevation is zero, what power is extracted by the turbine when the flow rate is 0.0045 m'/s of water at 20°C (p= 1000 kg/m)?

03: There are three connected pipes (38 m length of 5 cm pipe diameter),. (23 m length of 15 em pipe diameter) and (46 m length of 7.5 cm pipe diameter), all of them made of cast iron, as shown in Figure 2. There are three 90° elbows and an open globe valve, all flanged. If the exit elevation is zero, what power is extracted by the turbine when the flow rate is 0.0045 m'/s of water at 20°C (p= 1000 kg/m)?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In Figure below, the pipe entrance is sharp-edged having K1 = 0.5, and for the open globe valve assume K2 = 6.0. The flow rate of water is 0.015 m'/s. 3 (a) Calculate the velocity and Reynolds number of flow. (b) Find the head loss due to friction, hf (in m). (c) Calculate the Turbine head (in m) and Power generated (in Watt). Given: Density of water, pwater = 1000 kg/m²; Viscosity of water, u = 0.001 kg/m.s; Friction factor from Moody Chart, f=0.024. Draw sketch and show all calculations. 1 Open globe valve Turbine 60 m Water Steel pipe: L= 140 m, D = 7.5 cm
Example -5.2- It is required to pump cooling water from storage pond to a condenser in a process plant situated 10 m above the level of the pond. 200 m of 74.2 mm i.d. pipe is available and the pump has the characteristics given below. The head loss in the condenser is equivalent to 16 velocity heads based on the flow in the 74.2 mm pipe. If the friction factor = 0.003, estimate the rate of flow and the power to be supplied to the pump assuming n = 0.5 Q (m³/s) 0.0028 0.0039 0.005 0.0056 0.0059 Ah (m) 23.2 21.3 18.9 15.2 11.0
The water is pumped from a 40 sch pipe that has 750 ft lenght, 6 in. nominal diameters. Height difference between exit and entry planes is stated as 50 ft. The yield of waterpump, 80% the power of pump motor is 20 horsepowers. Friction losses are stated as 50ft-lbf/lbm. Please calculate the flow rate in pipe line.
2. A turbine is used to produce 2700 hp by expanding the water between points 1 and 2. Water flow rate, static pressures and pipe diameters are given. Calculate the power lost in between point one and two. Note that the static pressure at point 2 is given in vacuum. (SGH =13.6) P1 = 60 psi Q = 150 ft³/s D = 3 ft Section (1) Turbine 10 ft P2 10-in. Hg %3D vacuum D2 = 4 ft Section (2)
Water is to be pumped through 1500 ft of pipe from the lower to upper reservoir at a rate of 4 ft'/s, as shown in Figure below. The pipe is cast iron of diameter 8 inch. The pump is 80% efficient. (a) Find the velocity and Reynolds number of flow through pipe. (b) Find the head loss due to friction, h in ft. (c) Compute the pump head, h, in ft and the pump power needed, Ppump in horse power (hp). Given: Density of water, pwater = 1.94 slug/ft'; Viscosity of water, u = 2.05 x 10° slug/ft.s; Friction factor from Moody Chart, f= 0.021. Draw sketch and show all calculations. 180 ft L-1500 ft, D-8 in Pump
62.4¹,Mw lb Water (Yw ft³ an average velocity of 5 ft/s. Find the change in pressure over 39 ft of pipe. Provide your answer in = D 23.6 x 10-6 ) flows through the 4-in. diameter pipe below with -6 lb-s ft² lb ft² The pipe has roughness of 2x10-4ft. L
Find the loss in total pressure for each run in the simple duct system of Fig. 1, using the equal-friction method and in English unit. The total pressure available for the duct system is 0.12 in. wg (30 Pa), and the loss in total pressure for each diffuser at the specified flow rate is 0.02 in. wg (5 Pa). Duct fittings are listed in Table 1. Assume the duct dimeter in run 1 is 10 in. and the rest are 8 in. Does the duct system require any adjustment? 150 cfm e. a 15 ft Plenum е 15 ft 5 ft 5 ft a 3. 20 ft 4 10 ft 200 cfm e 10 ft 150 cfm b Duct Fittings for Figure 1 Fittings Type Abrupt Entrance 90 deg Elbow, Pleated Round to Rectangular boot, Straight 45 deg. Converging Wye 45 deg Elbow, Pleated a d e
Water is to be pumped through 1500 ft of pipe from the lower to upper reservoir at a rate of 4 ft'/s, as shown in Figure below. The pipe is cast iron of diameter 8 inch. The pump is 80% efficient. (a) Find the velocity and Reynolds number of flow through pipe. (b) Find the head loss due to friction, hf in ft. (c) Compute the pump head, h, in ft and the pump power needed, Ppump in horse power (hp). Given: Density of water, pwater= 1.94 slug/ft'; Viscosity of water, u = 2.05 × 10° slug/ft.s; Friction factor from Moody Chart, f= 0.021. Draw sketch and show all calculations. 180 ft L = 1500 ft, D = 8 in Pump
B- Calculate the power required for a water pump used in a closed system with flow rate Q=0.0076 m³/s. Assume that section area=0.00511 m² and at the area at the discharge is 0.0037 m². As AJ Water Suction Discharge pump Inlet gauge pressure=147 kPa Outlet gauge pressure=250 kPa
Q1/ Water. p=1.94 slugs/ft' and v=0.000011 ft/s, is pumped between two reservoirs at 0.2 ft/s through 400 It of 2-in-diameter pipe and several minor losses coefficient is(12.2m), as shown in Fig. 1. The roughness ratio is s/d = 0.001. Compute the pump horsepower required. MY (2) Z₂=120ft Z=20 ft Pump Fig.1 D=2 in
Find The size of the Valve in inches on Stream number: 1140 Temperature: 115°C Pressure (psi): 87.02 Flow rate GPM: 5.480
A pumping system has the following characteristics, f=0.015 length of thepipe = (2500 ft) pipe diameter 6 in, losses less than 0.5, the pipeis cast iron, and the system curve is:Hp= 34+ 5.47Q2Knowing that the system curve and the pump curve intersect at 12 cfsa. Determine Operation headb. Determine dischargec. Plot the system curve