Water at 20°C (p=998 kg/m³) is pumped out of a 10 cm in diameter pipe that con- sists of a 2 m long vertical section, and a 1 m long horizontal section. The pressure at the inflow is P1 25000 Pa (gage), and water discharges to the atmosphere at a velocity of V2 = 5 m/s. The mass of the horizontal section, when filled with water, is MH = 15kg per unit length. The pipe is anchored on the ground by a concrete base. Determine the resistive torque Tд acting on the concrete base (point A). Consider g = 9.81 m/s². Answer: TA = -319.02 N. m. 1m 2m D₁ 42 A 7x

Water at 20°C (p=998 kg/m³) is pumped out of a 10 cm in diameter pipe that con- sists of a 2 m long vertical section, and a 1 m long horizontal section. The pressure at the inflow is P1 25000 Pa (gage), and water discharges to the atmosphere at a velocity of V2 = 5 m/s. The mass of the horizontal section, when filled with water, is MH = 15kg per unit length. The pipe is anchored on the ground by a concrete base. Determine the resistive torque Tд acting on the concrete base (point A). Consider g = 9.81 m/s². Answer: TA = -319.02 N. m. 1m 2m D₁ 42 A 7x

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

7.35 In this system, d = 6 in., D = 12 in., Az = 6 ft, and Az2 = 12 ft. The discharge of water in the system is 10 cfs. Is the machine a pump or a turbine? What are the pressures at points A and B? Neglect head losses. Assume a = 1.0 at all locations. Water T-10ºC Same elevation- Machine Azz Az
The flow is opened to the atmosphere at point D which is fed by a very wide reservoir that has a water surface elevation of (5+) meters as shown in the figure given below. Elevation of the horizontal axis BC is 1 meter. At sections AB the diameter of the pipe is (0.2+- meters and CD the diameter of the 100 pipe is (0.3+: meters. The flow is ideal (inviscid) and absolute atmosphere pressure is 9.81 N/cm?. Considering the pipe's diameter is (0.15+; m at section BC, find the discharges and the 100 а. velocities of the flow at other sections (AE, EB, BC, CF, FD). Draw the energy and hydraulic grade lines of the system. b. Assuming the system discharge is constant and has the value you have found in (a), calculate the minimum pipe diameter that the section BC can take and draw the energy and hydraulic grade lines of this situation. Note: Absolute vapor pressure of water is 2.26 kN/m?. 10 A E 2.5 D B m
10. Water flows from a large reservoir as shown. The pipe is cast Iron, with inside diameter of 0.2 m. The flow rate is 0.14 m³/sec, and the discharge is to atmospheric pressure. The mean temperature for the flow is 10°C. The system is insulated. Determine the gage pressure P1, required to produce the flow. 200 m 2 1 150 m 100 m z=0 500 m
liquid flows into the tank at A at 4 m/s. Determine the rate, dy/dt, at which the level of the liquid is rising in the tank. The cross-sectional area of the pipe at A is AA = 0.1 m2. 3 m 4 m/s
2. Oil is pumped from reservoir A to B by a 15 hp pump having an efficiency of 75%. The pressure of air inside the tank is 4000 kg/m². Assume head loss to be 1.5 m of oil, determine the discharge. Use specific gravity of oil is 0.85. el. 14.71m el. 10m Air Oil s=0.85 A P el 30m B
Water is pumped up from a reservoir to a smaller holding tank. If the flow rate through the pipe is 50 LPM, find the NPSH available immediately before the pump. The length of the pipe from the reservoir to the pump is 13.1 meters, and its diameter is 2.8 cm. The distance is h2=6.8 m. Assume a friction factor of 0.021. The vapor pressure of water at the current temperature is 2,399 Pa. Current atmospheric pressure is 95,194 Pa. The density of water is 991 kg/m^3
A pipe (AB) that is 2300 m long and 400 mm diameter ,carries 150 L/s, C=100 ,the elevation of point A is 30m ,the elevation of point B is 27m and the pressure at point A is 40 m H,0. The pressure at point B will be approximately: Select one: а. 30.5 m b. 34.6 m ос. 37.6 m d. 33.5 m
Situation 1: In the pipe system shown, the velocity of water in pipe A is 1 m/s. The friction factor f = 0.02 for all pipes. a. Determine the discharge in pipe B. b. Determine the velocity in pipe C. c. Determine the headloss in pipe E. d. Determine the difference in elevation of the two reservoirs. Water D A 300 m 200 mm D 300m 500 mm Diom 600m 300mm Diam 300m 300mm D B 800 m 300mm Diam E
A 500 mm diameter pipe carries water at a rate of 500 L/s. A pump in the pipe is used to move the water from point A (El 30 m) to point B (El 40 m). The pressure is 70 kPa in A and 350 kPa in B. Assume a head loss of 3 m from point A to point B. a.What is the velocity of flow? ts) b. What is the head supplied by the pump? c. What horse power must be supplied to the flow by the pump if it is 85% efficient?
c. 56.23 N/m3 d. 60.18 N/m2 Situatton XC: In the figure shown, z,-4 m, length of pipe from the reservoir to the pump is 120 m, from the pump to the nozzle is 1000 m. The diameters of pipes are 0.60 and 0.45 m respectively. The gage pressure at B (the suction side of the pump) is -64 KPa. Neglect minor losses. D. B. 0.45 m diam. LcD=1000 m f%=0.02 %3D Zp = 4 m 0.60 m diam. LAB= 120 m f%30.02 52. Compute the velocity of water in pipe AB. a. 2.297 m/s b. 1.452 m/s c. 3.147 m/s d. 2.672 m/s 53. Compute the velocity of water in pipe CD. a. 1.23 m/s b. 4.08 m/s C. 3.56 m/s d. 5.59 m/s 54. Compute the discharge of the pipe from A to B due to pumping. a. 0.65 m/s b. 0.45 m2/s c. 0.89 m/s d. 0.25 m /s 60m. -0.02 m and loss of head
A water main line is composed of two pipes connected in series, pipes AB and BC. Pipe AB is 500 m long and 30 cm in diameter while pipe BC is 800 m long and 20 cm in diameter. Point C is 10 m higher than point A. The pressure at point C is 3 kg per square cm higher than the pressure at point A and the coefficient for minor head losses due to contraction and enlargement are 0.40 and 0.25 respectively. Determine the discharge and flow direction on the water main line using Darcy-Weisbach formula with f = 0.02 for all pipes. Draw approximately the EGL and HGL.
A pipe discharges 130 lps of water into a reservoir at a point 1.85 m belowthe water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25m above the water surface. At the discharge end the pipe is 30.5 cm. If the head lossfrom A to the reservoir is 0.7 m, determine the pressure in A.