our día = 25cm 20cm G=2.1 water A cylindrical container, whose who is 65 N is inverted and pressed into water as shown above. Determine the differential height (h) of the manometer & the bone F needed to hold the container in the he position shown ?

Q: 3. Determine the slope and vertical displacement of point A on the beam shown in the accompanying…

A:

Q: F cur día=25cm TASTA 20cm G=2.1 water 4 cylindrical container, whose wt. is 65 N is inverted and…

A:

Q: determine the moment of inertia along x and y axis with respect to the given axis and with respect…

A:

Q: 1.00 50 2 1.60 2.00 20 13 B

A:

Q: The blocks shown are separated by a solid strut which is attached to the blocks with frictionless…

A:

Q: 2 A rectangular gate AB hinged at A has a width of 2.0 m perpendicular to the paper and has…

A: Given, b= 2m unit weight of water=9.80 kN/m3 To determine, Magnitude of hydrostatic force in kN.

Q: Evaluate the factor 6Aã/L for the beam given in Fig. 1. The answer must be expressed in terms of the…

A: Given data:

Q: Determine the speed at which the basketball at A must be thrown at the angle of 30° so that it makes…

A:

Q: A 443-lb block is resting on a rough horizontal surface for which the coefficient of friction is…

A: Given data Weight of Block Equal to 443 LB Coefficient of friction is equal to 0.4 We are asked to…

Q: Determine the spacing of vertical stirrups near the left support of the "L"(m) beam loaded as shown…

A:

Q: A distributed load is applied to a beam, as shown in the Figure. From O, the load is zero and…

A: Given,

Q: Solve for the value of the vertical reaction at A, in kN. If downwards, affix a negative sign before…

A:

Q: Complete the table by providing the appropriate values. Loading 6Aā /L 6Ab /L 30, kN 4m 6m 10 m 5…

A:

Q: 23 and 24 please :) ill thumbs up

A: Given data: 23: Q=60 cfs H=3 ft   24: D=2 in  V= 120 ft/sec

Q: Situation: A bicycle tire is inflated with air. The density of the air in the inflated tire is 0.4…

A:

Q: Determine the x-, y-, and z-coordinates of the mass center of the body constructed of uniform…

A:

Q: The ball at A is kicked with a speed of (24 +0.01) m/s at an angle e = (25 +0.1)°. Determine the…

A:

Q: At the position shown, the end A of the od has a rightward component of velocity of 0.6 m/s and a…

A:

Q: A rectangular gate AB hinged at A has a width 2.0 m perpendicular to the paper, has a negligible…

A:

Q: As shown is a cylinder (?=0.8 m,) that is hinged at O. Compute the FR and ϴx. Analyze 1 m length.…

A:

Q: A metal part is hanging by a thin cord from a floating wood block. The wood block has a specific…

A:

Q: solution

A:

Q: Q2. Analyze the following frame as shown in the figure. AB has 21, BC has 1.51, and BD has I. 120 kN…

A: carry over moment -  its the moment developed at one end due to applied moment at other end .  when…

Q: Part A The assembly consists of two 15-kg bars which are pin connected. The bars are released from…

A:

Q: answers should be in 3 decimal places The rotation of a flywheel is defined by the rotation ω =…

A:

Q: the vertical reaction at A, in kN. If dov ut the units. Just input the numerical

A:

Q: Figure 0.3 m 0.4 m 0.2 m 1 of 1 > Part A Determine the magnitude of the moment of the force F= (2801…

A:

Q: Determine the magnitude of the resultant, its direction and position from point A. (3 decimal places…

A:

Q: standardized 15°C with a standard pull of 10 kg. The recorded distance was found out to be 430.60…

A:

Q: A rigid bar is supported by a spring as shown in figure below: A Tele 50 kN/m 5m 5m The deflection…

A: For a rigid bar supported by a spring,To find the deflection of point C

Q: The 190-lb man with center of gravity G supports the 97-lb drum as shown. Find the greatest distance…

A:

Q: Calculate the moment of inertia of the shaded area about the x-axis. Assume a = 45 mm, r = 30 mm.

A:

Q: The Uniform AB brass bar is fixed with support and pin as shown in the figure and has a rectangular…

A: Solution Given data P=1.8 kN, L= 7m, d=60 mm, E=150 GPa

Q: 1. Cords are looped around a small spacer separating two cylinders each weighing 400 KN and pass…

A: Given values: Weight of pulley 1 = 200 KN Weight of pulley 2 = 400 KN Weight of 2 cylinders…

Q: 20 kN/m Constant EI A В C D E F 5m 5m 3m

A: Given Data    Solution

Q: Determine the moment of inertia ly (in.“) of the shaded area about the y-axis. Given: x = 4 in. y =…

A: To Find :- moment of inertia Iy of shaded portion about Y- axis.

Q: 2) The above pipe is 2.4 feet long and twists over the whole length of the pipe, what is the angle…

A:

Q: Determine the moment of inertia Ix (in.4) of the shaded area about the y-axis. Given: x = 3 in. y =…

A:

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.