A Warren girder truss having a span of 20 m consists of four equal panelsas shown in figure below:U₁-5m 5m 5m 5mU₁U₂U360° 60° 60° 60° W 60° 60° 60° 60°4₁12L3L₁U₁What can be the magnitude of maximum tensile force (in kN) developed inmember U₁L2 if UDL of 3 kN/m of length 15m passes over the girder fromleft to right? (Round off to nearest integer).

For given warren girder truss,Span length : 20 m

A Warren girder truss having a span of 20 m consists of four equal panels as shown in figure below: L₂ -5m-5m-5m-5m- U₂ U₂ Us 60⁰ 60⁰ 60⁰ 60⁰ 60⁰ 60⁰ 60⁰ 60⁰ 4₁ 1₂ L₂ L What can be the magnitude of maximum tensile force (in kN) developed in member U₁L₂ if UDL of 3 kN/m of length 15m passes over the girder from left to right? (Round off to nearest integer).

A Warren girder truss having a span of 20 m consists of four equal panels as shown in figure below: L₂ -5m-5m-5m-5m- U₂ U₂ Us 60⁰ 60⁰ 60⁰ 60⁰ 60⁰ 60⁰ 60⁰ 60⁰ 4₁ 1₂ L₂ L What can be the magnitude of maximum tensile force (in kN) developed in member U₁L₂ if UDL of 3 kN/m of length 15m passes over the girder from left to right? (Round off to nearest integer).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the bridge truss shown, the end chord AB is composed of two C 230 x 30 channels latticed together so that the fabricated section has equal moments inertia about the axes of symmetry. Fy=290 MPa Properties of one C 230 x 30 Ix=25.5x105 mm² A = 3800 mm² B VP P CHIL ENGINEERING-STEEL DESIGN
3 The rigid bar EFG is supported by the truss system shown. Determine the cross- sectional area of member AE for which the normal stress in the member is 105 MPa. 0.90 SONRAWING D B R 15 kN -1.2 m 1.2 m-1.2 m-
11. Link BC is 6 mm thick and is made of a steel with a 450-MPa ultimate strength in tension. What should be its width w if the structure shown being designed to support a 20-kN load P with a factor of safety of 3? 600 mm- A B 90 480 mm
Figure 6: X 5 m 5 m A 5 m 20 KN A simple truss is subjected to 20 kN force at the point A as shown in Figure 6. The reaction force at point C is (in kN): (a) 20 Compression (b) 20 Tension (c) 30 Compression (d) 30 Tension الاختيارات B A O со
Q₁: Analyze the truss shown below B с <50k 3m IMI A E 100ku EA is Constant for all members + Am X Am
Question The degree of static indeterminacy for space truss shown below is H G D E
For the truss shown below determine the member forces in BC, CI, and IJ in kilonewtons. (Due to the nature of this problem, do not use rounded intermediate values in your calculations- B 3 m M 1.284 kN 1.070 kN 856 N 642 N 428 N 214 N 6@1.5 m = 9 m FBC magnitude kN sense tension FCI magnitude kN sense compression IJ magnitude kN sense compression
2. For the truss shown below, determine the stress in members AC and BD. The cross-sectional area of each member is 850mm². [94.12, 78.42 MPa] A 000 RA B 70kN E 4 panels at 4m 16m = G 30kN H RH 3m
The members of the truss shown below have a cross-sectional area of 10,000 mm2. Determine the stresses in members AB and AE in MPa. Indicate if the stresses are in compression or tension. 3 m 3 m C E 40 kN 80 kN F. 6m- 3 m-
A simply supported beam of span L and flexural rigidity EI, carries a unit point load at its centre. The strain energy in the beam due to bending is 1³ 13 48 EI 192 EI (a) (c) 1³ 96 EI (b) (d) L3 16 EI
B 6m LP P -8m- -8m- -8m -8m In the bridge truss shown in figure, the end chord AB is composed of two C 230 x 30 channels latticed together so that the fabricated section has equal moments of inertia about the axes of symmetry. Properties of C 230 x 30 Ix = 25.5 x 10^6 mm^4 A=3800 mm^2 %3D a. Determine the slenderness ration of section AB. b. Determine the capacity of member AB. c. If the safe load P on the truss is governed by the strength of member AB, which of the following gives the value of P using NSCP Specifications with Fy = 290 MPa. %3D
The Figure below shows a two-member truss supporting a block of weight W. The cross-sectional areas of the members are 800 mm² for AB and 400 mm² for AC. Determine the maximum safe value of W (kN) if the working stresses are 110 MPa for AB and 120 MPa for AC. ... B 40 deg. A 60 deg. A) 38.90 в) 55.30 61.70 76.2