The strain in the x-direction at point A (shown in fig.) on the steel beam is measured and found to be ɛx = 139 x 106. The shear strain at point A is found to be yxY = Rx 10 radians. The magnitude R is given by: (Take E= 204 GPa and Poisson's ratio =0.3). The cross-section of the beam is rectangular with depth 400mm and width 200mm respectively 100m 40omm 400m 600mın 1000 mm 200mm

The strain in the x-direction at point A (shown in fig.) on the steel beam is measured and found to be ɛx = 139 x 106. The shear strain at point A is found to be yxY = Rx 10 radians. The magnitude R is given by: (Take E= 204 GPa and Poisson's ratio =0.3). The cross-section of the beam is rectangular with depth 400mm and width 200mm respectively 100m 40omm 400m 600mın 1000 mm 200mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Draw Mohr's circle for the following plane strain state. Then compute (or extract from your drawing) the principal strains and max shear strain. (Positive sign convention for each is shown on the figure.) Ex = 200μ, Ey=-200μ, Yxy = 50μ (rad) Ex
A cantilever beam shown is subjected to vertical force P. A strain rosette is bonded at point A in the orientation shown in Fig. The material properties are E = 200 GPa, G = 80 GPa and ν = 0.3. If the recorded strain rosette readings are εa = +320μ, εb = +8μ and εc = +8μ, find the following: a) The state of strain at point A in x-y direction and sketch the strain element b)The principal strain and maximum in-plane shear strain at point A and sketch the corresponding strain element. c) Does the absolute maximum shear strain at point A occurs in-plane or out-of plane and find the magnitude of force P
R= 76 A copper wire of length (400+R) cm , diameter of (4+R) mm and mass of (5000 + R) g, if Young's Module of copper is (100 + R) × 10°N/m² : a. Find the stress in the wire. b. Determine the strain. C. How much it will be lengthened if the original length is 3.7 m?
The Poisson ratio formula for an auxetic structure given in the figure is given as follows:H = 8 cmL = 4 cmα = 50 °t = 5 mmThe strain value of the structure in the same direction as a result of the pull applied in the X axis from the bottom was measured as 0.26 mm / mm. Under the same loading condition:a) Calculate the strain on the Z axis of the structure.
The strain at point A on a beam has components Px = 450(10-6), Py = 825(10-6), gxy = 275(10-6), Pz = 0. Determine (a) the principal strains at A, (b) the maximum shear strain in the x–y plane, and (c) the absolute maximumshear strain.
10/10 find the strain( €) in x-axis only . if .Poisson ratio=D0.25, E= 200 GPa 14 kN 10 kN 12 kN 15 mm 10 mm 20 mm
uniform diameter d= 1.75 in. Segment (1) is an aluminum Ę₁ = 10000 ksi L₁ = 90 in. Segment (2) is a copper Ę₂ = 17000 ksi L₂ = 126 in. When Pis applied, a strain gage attached to copper segment (2) measures a normal strain of &2 = 1700 uin./in. in the longitudinal direction. What is the elongation of segment (1)? Answer in inch rounded-off to 3 decimal places L₁ A (1) Aluminum B L2 (2) Copper
Find the value of strain stress 30 MPa Modulus of elasticity=65 MPa
A steel wire having cross section area 2 mm2 is stretched by 10 N. Find the lateral strain produced I the wire. (Given Y for steel = 2 x 1011 N/m2, Poisson's ratio σ=0.29)
The state of strain in a plane element is Ex = -300 x 10-6 , Ey= 450 x 10-6, and Yxy = 275 x 10-6. (a) Use the strain transformation equations to determine the equivalent strain components on an element oriented at an angle of 0 = 30° counterclockwise from the original position. (b) Sketch the deformed element due to these strains within the x-y plane.
2. For the dimensions provided below, what would be the expected strain at point A if the displacement along the y-axis at point B in the diagram was = - -0.05 in? Property/Dimension Value a b t W E A X -a 8.00 2.00 0.25 1.00 10 L LL F B b Units in in in in MPsi C cross-section of beam W t
Draw Mohr's circle for the following plane strain state. Then compute (or extract from your drawing) the principal strains and max shear strain. (Positive sign convention for each is shown on the figure.) Ex = 200μ, Ey=-200μ, Yxy = 50μ (rad) You For the previous problem, compute the following six stress quantities: d. dy, dz. Txy, Tyz. Tzx. Assume this is an aluminum alloy (E = 10,000 ksi, G = 3800 ksi, v = 0.33). Do not forget units! Ex