A rectangular block is 7 cm long in the x-direction, 5 cm in the y-direction, and 9 cm long in the z-direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 15 kN in the x- direction, 21 kN in the y-direction, and 18 kN in the z-direction. Calculate the strain in the direction y if Poisson's ratio v = 0.30 and having a modulus of elasticity of E = 150 GPa. y 7 cm 9 cm 21 kN 15 kN 5 cm 18 kN

A rectangular block is 7 cm long in the x-direction, 5 cm in the y-direction, and 9 cm long in the z-direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 15 kN in the x- direction, 21 kN in the y-direction, and 18 kN in the z-direction. Calculate the strain in the direction y if Poisson's ratio v = 0.30 and having a modulus of elasticity of E = 150 GPa. y 7 cm 9 cm 21 kN 15 kN 5 cm 18 kN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.7P: A thin square plate in biaxial stress is subjected to stresses ?? and ??., as shown in part a of the...

See similar textbooks

Similar questions

- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
A thin square plate in biaxial stress is subjected to stresses ?? and ??., as shown in part a of the figure. The width of the plate is h = 12.0 in. Measurements show that the normal strains in the x and v directions are s = 427 × 10-6 and s = 113 × l0-6, respectively. With reference to part b of the figure. which shows a Iwo-dimensional view of the plate. determine the following quantities. (a) The increase .d in the length of diagonal Oil. (b) The change . in the angle between diagonal Oti and the x axis, (c) The shear strain y associated with diagonals Oil and cf(that is. find the decrease in angle ced).
Use the principle of Strain energy due to direct stresses strength of materials 2
A rectangular steel block is 300mm in the x direction, 200mm in the y direction and 150mm in the z direction. The block is subjected to a triaxial loading consisting of three uniformly distributed forces as follows: 250kN tension in the x direction, 320kN compression in the y direction and 180kN tension in the z direction. For steel, v=0.30 and E=200,000MPa. Determine the total strain in the x direction due to the forces applied in the three directions.
2. The tires of an agricultural tractor shown below are assumed to be 25 cm wide for the front tires and 40 cm at the rear tires. Ground contact of each tire is 15 cm. Calculate the compressive stress between each tire and the ground surface. Weight = 2,500 kg 15 cm 1.3m Point A 2.2 m 2R 2F
A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in the z direction. If the Poisson’ Ration is 0.30 and the modulus of elasticity is 29xksi, determine the deformations at each direction. Also, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
An 8.03-kg stone at the end of a steel (Young's modulus 2.0 x 1011 N/m2) wire is being whirled in a circle at a constant tangential speed of 19.8 m/s. The stone is moving on the surface of a frictionless horizontal table. The wire is 4.22 m long and has a radius of 4.94 x 10-3 m. Find the strain in the wire.
An element of bone in plane strain where the state of strain are = 12 x 10-4). Find (a) the stresses at (Ex = 8 x 10-4, €y = 5 x 10-4, Yxy orientation a counterclockwise angle (40 deg.) from the x-axis, b) the strain energy and (c) the failure stress by Von Misses criteria. Known Modulus of elasticity = 2 x 10° N/m² and Poisson's ratio = 0.3
(b) Consider a square element in the x-y plane with side length of 3 cm. The thickness of the element is 7 mm. The element has modulus of elasticity of 200 GPa and Poison's ratio of 0.33. If the element is subjected to forces in the x and y directions of 3 KN and 1.5 KN, respectively, find the dimensions of the loaded element.
A rectangular block has dimensions of 3 in, 4 in, and 5 in along the X-, y-, and z- axes, respectively. The block is subjected to triaxial loading of three uniformly distributed loadings of 30 kips (C), 45 kips (T), and 60 kips (C) along the x-, y-, and z- axes, respectively. If the strain along the X- axis and the z-axis are 0.00021 (C) and 0.00042 (T), respectively, determine the Poisson's ratio and the modulus of elasticity of the material. Also, what is the change in volume of the material?
If the Young's modulus and Poisson's ratio of the container material are 100 GPa and 0.3 respectively, What is the axial strain in the cylinder wall at mid-depth?
A thin polymer plate PQR is deformed so that corner Q is displaced downward by a distance L = 0.50 mm to new position Q' as shown. Determine the shear strain at Q' associated with the two edges (PQ and QR). 120 mm 480 mm R 240 mm -891 urad -1160 μrad -811 urad -1248 urad -1436 prad X