The phasor voltage Vab in the circuit shown is 24020 ° V (rms) when no external load is connected to the terminals a, b. When a load having an impedance of 80 – j 60 Q is connected across a, b, the value of Vab is 115.2 + j 33.6 V (rms) . a) Find the impedance that should be connected across a, b for maximum average power transfer. b) Find the maximum average power transferred to the load of (a). A circuit operating in the sinusoidal steady Vab -

The phasor voltage Vab in the circuit shown is 24020 ° V (rms) when no external load is connected to the terminals a, b. When a load having an impedance of 80 – j 60 Q is connected across a, b, the value of Vab is 115.2 + j 33.6 V (rms) . a) Find the impedance that should be connected across a, b for maximum average power transfer. b) Find the maximum average power transferred to the load of (a). A circuit operating in the sinusoidal steady Vab -

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
For the phasor diagram in figure 6 express the voltages in sinusoids for a period of 5ms. Im Re )e,=45° e,=20 Vz=10 V2=8 Figure 7 a. Va(t)=. b. V2(t)=. c. What is the rms voltage of V1 = d. What is the rms voltage of V2=_ e. What is the frequency in Hz = f. What is the angular frequency =. In terms of lagging and leading what is the exact phase relationship between V, (t) and V2(t) g.
15 A of current is taken by a non-inductive load at 125 V. In order that the same current shall be generated from 240 V, 50 Hz mains. An inductor is now also then connected in series. Note: The resistance of the inductor should be ignored and also assume the waveform to be sinusoidal. Determine the phase difference between the current and the applied voltage, the impedance of the circuit and the inductance of the inductor.
Suppose I have two peak phasor voltages, V, = 100245° and V, = 75Z-60°. Circle Your Choices: I. The frequencies associated with the phasors are (0 Hz, 60 Hz, 50 Hz, Unknown). II. The rms value of the first phasor is (100, 70.7, 141, 200) volts. III. If you want to add these two phasors, the frequencies must be (60 Hz, 50 Hz, The same, Integer multiples of a given frequency.)
8. The total power supplied to a balance delta load is found in the same way as for a balance wye load. True False Either Neither 12. A load of 20 + j35 ohms is connected across a 220 V, 60 Hz supply. Find the reactive power of the load in var. 595 2420 1042 1382 13. A type of DC source where the characteristic output voltage has perfect unidirectional waveform and is based on electrochemical principle. Generator Inverter Converter Battery 14. Calculate the Rf of a circuit whose impedance is 20+j35 and current of 2A. 0.86 0.91 0.50 0.71 15. What capacitor shall be installed in parallel with a circuit to achieve a unity power factor if the reactive power of a circuit is 200VARS and the voltage is 100V. 80.45 microfarad 53.05 microfarad It's already in unity 62.45 microfarad
Two loads are connected in parallel to a 2000 V(rms) 50Hz source. one of the loads Each of them has 500KVAR reactive power and 0.6 reverse power factor. Other load 300KW since it has absorbing power and 100KVAR dissipating power a) Draw the equivalent circuit of the system b) Find the common power factor of the system c) In order for the power factor to be 0.98 back, the capacitor to be connected in parallel with the loads find its value d) The magnitude of the current drawn from the source is measured before and after the capacitor is connected Find and compare for the next cases. Not. Solve this question in detail step by step and explain your requests in detail
Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average and RMS for both currents. a = 50° T1 50 2 ot Vs = 300 sin 100rt T2 ot
lši vl pir:10 Expert Q&A + 1. For the circuit in Figure: a. Determine I, VR, and Ve in phasor form. b. Calculate the total power factor, and indicate whether it is leading or lagging. c. Calculate the average power delivered to the circuit. d. Draw the impedance diagram. e. Find the voltages VR and Vcusing the voltage divider rule and compare them with the results of part(a) above. + Uc - + Ug - 30 2 L = 0.2 H L =0.2 H C = 4 µF e = V2(20) sin(377t + 40°) Expert Answer Home Search More II
d. 565.685 V If a Load absorbs 20 kVA at a leading power factor of 0.6. Then the complex power is: Select one: O a. 12000 - j16000 VA O b.-12000 + j16000 VA O c. 12000 + j16000 VA O d. None of these Given the circuit below and the associated set of voltages and currents, the reactive Power developed by im voltage source is FENG300 MINTERM
An impedance load consisting of 12 ohms resistance and 16 ohms inductance reactance is connected across a 50 Hz, 100 V source. Find the capacitance of the condenser which may be paralleled with this load to bring the power factor to 0.80 leading.
2)With reference to the waveform given below formulate the equation for the average value of DC voltage available across the load, if the load connected is a pure resistive load and if the circuit applicable to this waveform is fed from a load having 180 ohm 50 Hz start connected input with the value of resistance equivalent to 200 ohm solve and obtain the value of Dc power in the load (3 phase bridge) Van Vbn Ven P 180° 210° 360° - Vm D1 & D2 DI&D6 D3 & D6 D3&D4 D5&D4 D5&D2 120° 120°