The economiser of a steam boiler receives its feed water at 34.6°C and supplies the evaporator at a temperature of 60.1°C. The water is then heated at a constant pressure of 600kPa and delivered with a dryness fraction of 0.73. The super-heater dries and superheats the steam to a specific volume of 0.394m³/kg. Determine the:

The economiser of a steam boiler receives its feed water at 34.6°C and supplies the evaporator at a temperature of 60.1°C. The water is then heated at a constant pressure of 600kPa and delivered with a dryness fraction of 0.73. The super-heater dries and superheats the steam to a specific volume of 0.394m³/kg. Determine the:

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter47: High-pressure, Low-pressure, And Absorption Chilled-water Systems

Section: Chapter Questions

Problem 13RQ: The subcooling temperature in a condenser can be measured by taking the difference between the A....

See similar textbooks

Similar questions

What are the approximate temperature ranges tor low-, medium-, and high-temperature refrigeration applications?
The evaporator design temperature may in some cases operate at a slightly ____(higher or lower) pressure and temperature on high-efficiency equipment because the evaporator is larger.
Condensers in these refrigerators are all_______cooled.
The subcooling temperature in a condenser can be measured by taking the difference between the A. suction pressure converted to temperature and the boiling refrigerant. B. boiling temperature and the condensing temperature. C. condensing temperature and the leaving-refrigerant temperature. D). condensing temperature and the entering-refrigerant temperature.
Why is two-stage compression popular for extra-low-temperature refrigeration systems?
Welded ______sealed compressors are normally used in household refrigerators.
A refrigeration system using refrigerant 12 is to have a refrigerating capacity of 80 kW. The cycle is a standard vapor-compression cycle in which the evaporating temperature is -15°C and the condensing temperature 30°C. At the entrance to the evaporator, what is the fraction of vapor in the mixture expressed on a mass basis? 0.97 0.29 0.92 0.27
The mass Q3// The Lithium bromide (Li Br) - water absorption refrigeration system as flow rate delivered by the solution pump is 0.4 kg/s. The temperatures in the: generator = 105 °C; condenser = 35 °C; evaporator = 5°C; and absorber = 30 °C. Determine: - 1- The mass flow rates of solution returning from the generator to the absorber 2- The mass flow rate of refrigerant flowing in the condenser. 3- The amount of heat in each component. 4- The COP.
The food storage room requires a cooling system with a capacity of 10 tons of refrigeration that operates at an evaporator temperature of -9.2 Celsius and a condenser temperature of 30.9 degrees Celsius. The refrigerant used is R-134a and the system operates in saturated conditions. Determine C.O.P, refrigerant flow rate and heat loss rate in the condenser.
Question 2 of 4 - / 25 An office building requires a heat transfer rate of 30 kW to maintain theinsidetemperature at 21°Cwhen theoutsidetemperature is O°C. Avapor-compression heat pump with Refrigerant 134a astheworkingfluid isto beused to provide the necessary heating. The compressoroperates adiabatically with an isentropic efficiency of 82%. Determine appropriate evaporator and condenser pressures of a cyclefor this purpose assuming ATcond = ATevap = 10°C, as shown in the T-sdiagram. The refrigerantexitstheevaporator assaturated vapor and exitsthecondenser as saturated liquid at the respective pressures. AT cond Outside air 21°C 0°C Inside air ATent Condenser Evaporator Expansion valve Compressor Step 1 Determinethe mass flow rate of refrigerant, in kg/s. m = kg/s Attempts: unlimited Submit Answer Save for Later Using multiple attempts will impact your score. 5% score reduction after attempt 2 Step 2 The partsof thisquestion must becompleted in order. This partwill be availablewhen…
A refrigeration system using R22 is to have a refrigerating capacity of 60 kW. The evaporating temperature is -5degC and condensing temperature of 35 deg-C. Determine the volume flow rate of the refrigerant at the inlet to the compressor, the power required by the compressor, and the fraction of vapor in the mixture at the entrance to the evaporator. Use the spreadsheet to solve this problem.
A refrigeration system using refrigerant 12 is to have a refrigerating capacity of 80 kW. The cycle is a standard vapor-compression cycle in which the evaporating temperature is -15°C and the condensing temperature 30°C. Determine the volume flow of refrigerant measured in liters per second at the inlet to the compressor.