refrigeration system using refrigerant 12 is to have a refrigerating capacity of 80 kW. The cycle is a standard vapor-compression cycle in which the evaporating temperature is -15°C and the condensing temperature 30°C. At the entrance to the evaporator, what is the fraction of vapor in the mixture expressed on a mass basis? 0.97 0.29 0.92 0.27

refrigeration system using refrigerant 12 is to have a refrigerating capacity of 80 kW. The cycle is a standard vapor-compression cycle in which the evaporating temperature is -15°C and the condensing temperature 30°C. At the entrance to the evaporator, what is the fraction of vapor in the mixture expressed on a mass basis? 0.97 0.29 0.92 0.27

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter3: Refrigeration And Refrigerants

Section: Chapter Questions

Problem 2RQ: What are the approximate temperature ranges tor low-, medium-, and high-temperature refrigeration...

See similar textbooks

Similar questions

What are the approximate temperature ranges tor low-, medium-, and high-temperature refrigeration applications?
Condensers in these refrigerators are all_______cooled.
What are higher-efficiency refrigerant blends that can be used as long-term replacements for R-22 in residential and light-commercial air-conditioning applications?
Welded ______sealed compressors are normally used in household refrigerators.
Four methods for controlling head pressure in an air-cooled condenser are ______, ______, _______, and
2. A Refrigeration system using R-22 has a capacity of 320 kW of refrigeration. The evaporating temperature is -10°C and the condensing temperature is 40°C. Calculate the dryness fraction in the mixture before the evaporator. A. 0.287 B. 0.315 C. 0.245 D. 0.227
Can you also show the T-s and P-h diagrams? A Single Stage Vapor Compression (SSVC) refrigeration system has a cooling capacity of 6 tons. The discharge of the evaporator is at -20°C & 0.1 MPa and the discharge of the condenser is at 30°C & 1.0 MPa. Determine the following: (a) the COP of the system, (b) the Energy Efficiency Ratio in kJ/hr/W, (c) the HP/ton of the system, (d) the Refrigerating Efficiency of the system.
A Single Stage Vapor Compression (SSVC) refrigeration system has a cooling capacity of 7.5 tons. The following are the actual conditions: discharge of the evaporator is at -30°C & 0.2 MPa, discharge of the condenser is at 30°C & 2.0 MPa, discharge of the compressor is at 130°C & 2.5 MPa. Determine the Refrigerating Efficiency of the system
A refrigeration system using refrigerant 12 is to have a refrigerating capacity of 80 kW. The cycle is a standard vapor-compression cycle in which the evaporating temperature is -15°C and the condensing temperature 30°C. Determine the volume flow of refrigerant measured in liters per second at the inlet to the compressor.
1. A standard refrigerating system with a heat exchanger is operating with a condenser pressure of 1571.2 kPa and evaporator pressure of 421.35 kPa using refrigerant R22. If the liquid line from the condenser is soldered to the suction line from the evaporator to form a heat exchanger and if as a result of this, the saturated vapor leaving the evaporator is superheated by 10. Determine (a) temperature of refrigerant entering the compressor (b) temperature of refrigerant leaving the compressor (c) degree superheat leaving the compressor (d) temperature of subcooled liquid leaving heat exchanger (e) degree subcooled leaving the heat exchanger (f) mass of flash gas per kg refrigerant entering evaporator (g) compression ratio (h) clearance volumetric efficiency of compressor if the clearance volume is 5% 18 answers (i) refrigerating effect (i) mass flow rate of refrigerant per ton of refrigeration (k) work on compressor (1) work on compressor per ton of refrigeration (m) condenser load (n)…
1. A standard refrigerating system with a heat exchanger is operating with a condenser pressure of 1571.2 kPa and evaporator pressure of 421.35 kPa using refrigerant R22. If the liquid line from the condenser is soldered to the suction line from the evaporator to form a heat exchanger and if as a result of this, the saturated vapor leaving the evaporator is superheated by 10.
In a certain refrigeration system for low temperature application, a two-stage operation is desirable which employs ammonia system that serves a 40 − ton evaporator at −30°C. The system uses a direct contact cascade condenser, and the condenser temperature is 40°C. Sketch the schematic diagram of the system and draw the complete process on the PH diagram b. The mass flow rate in the low loops in kg/s c. The mass flow rate in the low and high pressure loops in kg/s d. The total work