Answered: Estimate the thrust needed from the…

Name: 3. The hydraulic dredge shown below is used to dredge sand from a riv
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 3. The hydraulic dredge shown below is used to dredge sand from a river bottom.Estimate the thrust needed from the propeller to hold the boat stationary. Assume thespecific gravity of the sand/water mixture is SG = 1.4.9 ftProp30 ft/s30°2-ft diamete

Engineering

Mechanical Engineering

Estimate the thrust needed from the propeller to hold the boat stationary. cif.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.76P: A 6-in. diameter hole is drilled in the conical frustum. Calculate the volume and the surface area...

See similar textbooks

Similar questions

A 6-in. diameter hole is drilled in the conical frustum. Calculate the volume and the surface area of the resulting body.
find the specific gravity of the given unknown fluid, the hydrometry weight is 0.015 N. A0.1 cm? == 6.3 em -V= 1.0 cm
Find the location of resultant force( F)of the water on the triangular gate and the force(P) necessary to hold the gate in *.'the position shown in Fig.e=53 water 8 ate 5m Hing 3m P=51.09 KN O P= 61.09 KN O P= 71.09 KN O 2m
One side dimension of a rectangular tank is 1.5 m and 2 m deep. The tank filled with oil of mass density of 920 kg / (m ^ 3). Calculate the resultant force on this vertical end and the depth of the centre of pressure from the top.
Example: A hemisphere projection of diameter 0.6 m exists on one of the vertical sides of a tank. If the tank contains water to an elevation of 1.5 m above the center of the hemisphere, calculate the vertical and horizontal forces. Water 1.5 m o0.6 m N 立

3. Determine the magnitude and direction of the resultant force due to water on a quadrant shaped cylindrical gate as shown in Fig. Ex. 3.9. Check whether the resultant passes through the centre. 4 m Hinge WL Gate CG: 4r 4 m 4 m 123276 78480 Figure Ex. 3.9
An open cylinder tank, D= 1.0m, h=1.5m, contain water at depth 1.0m. If this tank rotate about its central vertical axis. Its the angular velocity without falling water from its open end * 8 rad/sec 8 rev/min 5 rad/sec 4.5 rad/min none of these=..
thi 40 A vertical sluice gate (4m) wide and (3m) deep contains water on both of its sides. On the upstream side, the water is (6m) deep and on the downstream side it is (2.5m) deep from the bottom of the sluice. What is the resultant pressure force on the gate and the position of this resultant force from the hinge
Calculate the hydrostatic pressure in a reservoir of depth 15 m and density of the fluid is 1000 kg/m³.
Describe the forces that enable the submarine to descend or ascend in the seawater. When the submarine holds at the constant depth of 3,500m, calculate the buoyant force on the submarine. weight of seawater in the ballast tank. seawater pressure. When seawater flows into the bottom opening at 10 m/s, calculate the velocity of the seawater level (8m above the bottom of the submarine) inside the ballast tank (v on diagram). Calculate the net force on the submarine circular hatch door (10m above the bottom of the submarine) with a radius of 0.5m. The air pressure inside the submarine below the hatch door is 150 101.3 kPa. Calculate the change in heat energy of the submarine’s outer haul, when it descends from the surface to a depth of 3,500m (with an average temperature of 20°C). Calculate the power of the submarine’s electrical heater needed, to maintain the interior of outer hull at 30°C. The exterior of outer hull is 10°C. (Assume heat of the submarine…
The tank in Fig. 2/is 3 m wide into the paper. Compute the hydrostatic (a) horizontal force component (b) vertical force component and (c) resultant force on quarter-circle panel BC. Consider y-9810 N/m b. 6 m Water Section A-A Fig. 1
A water tank is being towed on an uphill road that makes an angle of 14 deg with the horizontal with constant acceleration of 3.5 m/s^2 in the direction of motion. Determine the angle the free surface of water makes with the horizontal. ( With Free Body Diagram)