The cylindrical tank with a spherical end cap has an outer radius of 2 m and a wall thickness of 50 mm. If the tank is pressurized to 3.5 MPa, determine the longitudinal and circumferential stresses in the cylinder, and the stress in the end cap.

Q: A circular plate with simply supported edges subjected to a uniform pressure of P=1,450 KPa, as…

A:

Q: 2000 1 45001 3100 N

A: given; force in x-direction(Fx)=-2000N (compressive)force in y-direction(Fy)=-4500N…

Q: respectively. The tank has an inner diameter of 4 m. The thickness of the cylindrical are made from…

A: A scalar quantity in when when an amount of force act on the object in a cross section area, that is…

Q: A steel tube of 200 mm external diameter is to be shrunk onto another steel tube of 60 mm internal…

A: For inner tube: Write the expressions for A and B for thick cylinder. At r=0.030,…

Q: A thin-walled cylinder tank is subjected to a tensile stress of 100 Mpa. What is the longitudinal…

A: The tensile stress on the thin-walled cylinder tank is σt=100 MPa.

Q: occur in the n-n plane of the figure. Present a diagram showing such stresses on the n-n plane.…

A:

Q: A 1.5-m-diameter cylindrical tank is formed of 6-mm-thick sheet steel (E = 200 Gpa, ν = 0.3). The…

A: Given: The diameter of tank d=1.5 m=1500 mm The thickness of steel sheet t=6 mm The contents…

Q: Q2/ The rigid bar ABCD is supported by a pin at B and restrained by identical steel bars at C and D,…

A: Given data as per the question Increase in temperature =800 c E = 200 Gpa Area =250 mm2 considering…

Q: A boiler with an outside diameter of 300 mm, length of 1000 mm and a wall thickness of 10 mm is…

A:

Q: The maximum shear stress (in MPa) in the

A: Given;  A cylindrical tank of;  Inner radius,r=7 mm  Thickness=50 mm  Gauge pressure= 2 MPa…

Q: The plate in the figure has cross-sectional area A and is subjected to the axial load P. Determine…

A:

Q: Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: The normal strain measured on the outside surface of a spherical pressure vessel is 670 με. The…

A: μ=670 μ mm/mmd=1.20mt=10 mmE=73GPaν=0.33

Q: the (1) two subscripts and (2) sign of the stress components (\sigma, \tau) under the given…

A: we have to define the state of stress for the given coordinate system

Q: A pressurized steel tank has inner radius r = 0.5 m and wall thickness t = 20 mm. The steel has…

A: Given data: Before proceeding with the solution check whether it is a thin or thick pressure…

Q: A column has a square cross-section that increases by depth from 0.5 m to 1 m. If the column has a…

A: W are to derive the normal stress on section aa

Q: A boiler with an outside diameter of 300 mm, length of 1000 mm and a wall thickness of 10 mm is…

A: According to the information we have a boiler with a diameter of 300 mm and a length of 1000 mm…

Q: A spherical pressure vessel has an inside diameter of 4.8 m and a wall thickness of 9 mm. The vessel…

A:

Q: Calculate the normal stresses (in Pa) at point A of the bracket caused by the 11023 N force.

A: The stress due to normal force on the beam can be determined as,

Q: A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The…

A:

Q: The object (W 1000 lb) is moving between positions G and H back and forth repeatedly. The bar AD is…

A: W=1000 lbSy=80 ksi=80×103 psiS'n=20 ksi=20×103 ksiN=2

Q: The rigid bar of negligible weight is supported as shown. The assembly is initially stress-free.…

A:

Q: A thick cylinder of 0.5 m external diameter and 0.4 m internal diameter is subjected simultaneously…

A: A cylinder whose diameter to thickness ratio is less than 20 is termed as thick cylinder.

Q: A typical aluminum-allóy scuba diving tank is shown in thế ngure. The outside diameter óf the tank…

A: Solution:

Q: Determine the total pull exerted by the cold bar and the intensity of stress in it. Use E = 200 GPa

A: Determine total pull exerted by the cold bar and the intensity of stress in it

Q: Determine the equivalent state of stresses in an element at the point representing (a) the principal…

A:

Q: A vessel is pressurised at A. The ends of the vessel are shut with two-disc plates connected by the…

A: Given P=6.8 MPaE=210 GPaR=80 cm(Radius of vessel ) =D=160 cm t=12 mmd=12 cm (diameter of shaft )

Q: The propane storage tank shown in Photo has an outer diameter of 3.3 m and a wall thickness of 18…

A: Hello. Since your question has multiple parts, we will solve first question for you. If you want…

Q: torsion as shown. Determine the Perimeter of then

A: we know that , shear stress =T2t Am      A0 =T2tζ Am = A0T = Torque t = thickness to obtain area we…

Q: Find the longitudinal stress in the tank.

A: To Find the longitudinal stress.

Q: 3.5 m r= 0.6e-0.08y² y 0.6 m

A:

Q: In a plane stress condition, the components of stress at point are ox = 20 MPa, ơy = 80 MPa and txy…

A: Given, Stress in x-direction = σx = 20 MPa Stress in y-direction = σy = 80 MPa Sheat stress in…

Q: In a cylindrical container, Gas is compressed to a pressure of 3 MPa. If the cylinder has a diameter…

A: Boiler shells, pressure tanks, pipes, and other low-pressure processing equipment all use…

Q: Calculate the tangential stress at a point on the plate that forms a cylindrical reservoir, known as…

A:

Q: A closed cylindrical tank containing a pressurized fluid has an inside diameter of 820 mm and a wall…

A:

Q: A copper rod with 0.15 cm diameter is enclosed by a steel tube that has an outside diameter of 0.3…

A:

Q: B -1.5 m Figure 2 The -red-brass rod AB of 1.5 m and the aluminium rod BC of 1 m, shown in Figure 1,…

A:

Q: The gas storage tank is fabricated by bolting together two half cylindrical thin shells and two…

A:

Q: The 2-meter-high pressure tank below contains gas with internal pressure of 2 MPa. It is subjecte to…

A: Givenh=2mP=2MPaFex=15kNt=30mm=0.030m

Q: L = 3 m Figure P-265

A:

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.