The beam AB is attached to the wall in the xz plane by a fixed support at A. A force of F = = (-130² + 72.03 + 332k) N is applied to the end of the beam at B. The weight of the beam can be modeled with a uniform distributed load of intensity w = 60.0 N/m acting in the negative z direction along its entire length. Find the support reactions at A. Z с A = A Variable Value 6.10 m 6.00 m 3,20 m a b с b MA= X Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. k) N k) N-m B + F y cc 130 BY NC SA 2016 Eric Davishahl 3+

The beam AB is attached to the wall in the xz plane by a fixed support at A. A force of F = = (-130² + 72.03 + 332k) N is applied to the end of the beam at B. The weight of the beam can be modeled with a uniform distributed load of intensity w = 60.0 N/m acting in the negative z direction along its entire length. Find the support reactions at A. Z с A = A Variable Value 6.10 m 6.00 m 3,20 m a b с b MA= X Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. k) N k) N-m B + F y cc 130 BY NC SA 2016 Eric Davishahl 3+

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If Mz = 210 kip-ft, find the magnitude of the bending stress at a point H. For the beam cross section, assume a = 7 in. b = 10 in. d = 28 in. r = 3.5 in. The centroid of the cross section is located 12.88 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 15990 in.4.
In each case, calculate the reaction at A and then draw the free-body diagram of segment AB of the beam in order to determine the internal loading at B.
in each case, calculate the reaction at a and then draw the free-body diagram of segment ab of the beam in order.to determine the internal loading at b
Solve for the following internal forces occurring on the beam loaded as shown below. a. Moment at B in kN-m. b. Maximum negative shear in kN. c. Maximum negative moment in kN.
For the figure shown, determine the reaction of the hinge force at B as it acts upon member AC. (kN)
Solve for the following internal forces occurring on the beam loaded as shown below.a. Moment at B in kN-m. b. Maximum negative shear in kN. c. Maximum negative moment in kN.
The folded rush of the figure is supported by a bearing at point A, by a hinge in D and a BC cable at point B. Determine the components of the reactions on the supports in A and D and the tensile strength in the cable BC. Draw the free-body diagram.
Determine the maximum bending stress of D in the overhang beam. Point D is located just to the left of the roller support.
A 10 m long beam has 2 supports at point A and B. The beam is pinned at Support A and supported by a roller at Support B. It is carrying a car (mass of car= 1660kg) at middle of the beam. Draw the free-body diagram (FBD); construct the shear and bending moment diagram for this system. Discuss the results and explain the stress of this beam. Provide your opinion on the effect of the beam when the centroid of the vehicle is shifted to 3m away from Support B. Using equilibrium i.e. force and moment equilibrium must be satisfied for each component, determine the forces or/and moments. List all assumptions that are
Analyze the structure using slope deflection method and solve for the reaction at support A,B,C
Calculate the vertical reaction at B in kN for the loaded truss as shown in the figure. Assume the area of all members as the same.
F=1.7 kN W= 11.1 kN/m Find the reaction force and moment at support A Find the maximum absolute bending stress