Solve the following problem and show your complete solutions. INCLUDE FREE BODY DIAGRAM 1. Compute the maximum shear stress and the maximum flexural stress of the beam shown in the figure. The cross section of the beam is 200 mm x 400 mm. Draw and color the shear and moment diagrams. 10 KN A www B 1.00 10 KN/m 3.00 D.Lopez 15 KN/m umm 1.00 1.00 in meters D

Solve the following problem and show your complete solutions. INCLUDE FREE BODY DIAGRAM 1. Compute the maximum shear stress and the maximum flexural stress of the beam shown in the figure. The cross section of the beam is 200 mm x 400 mm. Draw and color the shear and moment diagrams. 10 KN A www B 1.00 10 KN/m 3.00 D.Lopez 15 KN/m umm 1.00 1.00 in meters D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the following unknowns on the beam shown below using Conjugate-Beam Method. Consider 250 mm x250 mm section and E = 200 GPa. Show complete and organized solution. a. Vertical Reaction at C in kN. b. Moment Reaction at C in kN-m. c. Deflection at point B in mm. d. Maximum deflection on the beam in mm Given: a- 4m b- 24kN/m c- 9kN
3) From the figure shown; a) Calculate the force in member AB. b) Calculate the force in member CD. c) Calculate the force in member BD. Indicate if tension or compression. 300KN 3m GookN B 2m A 50° 40,747 D 4m.
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Show complete and organized solutions. a. Vertical Reaction at B in kN.b. Moment Reaction at A in kN-m.c. Deflection at point C in mm.d. Deflection at midspan of AB in mm. Valuea = 3.7b = 26c = 29 Thank you very much!
An I beam whose flange width is 357mm, flange thickness is 15mm, web thickness is 20mm, total depth of 450mm and Fy of 248MPa is to be used to carry a uniform load all throughout its length, 3m. 1. What is the allowable bending stress? a. 153.69 MPa b. 161.75 MPa c. 192.69 MPa d. 168.23 MPa 2. Determine the moment of inertia of the section. a. 0.732 x 10⁹ mm⁴ b. 0.517 x 10⁹ mm⁴ c. 0.630 x 10⁹ mm⁴ d. 0.810 x 10⁹ mm⁴ 3. What is the maximum safe uniform load that the beam could carry? a. 402.58 kN/m b. 164.6 kN/m c. 476.56 kN/m d. 541.6 kN/m
Problem-1: The beam shown in figure below is subjected to a vertical distributed load at BC of 10 kN/m and a concentrated load at free end at D of 30 kN. Using the slope deflection method, determine the moment at the fixed end support A, the roller support B and C. Take I= 511062 mm“, E = 200 GPa. 30 kN 10 kN/m A -6 m- -9 m- -4 m- Solution: MAR -13.7 kN m Mac 27.5 kN-m 5 MBA = -27.5 kN m Mca -120 kN -m
PROBLEMThe beam shown below has internal hinges at points B and D. Assume EI is constant. Using your most convenient methodshow the following:a. Magnitude and directions of the support reactions (Ax,Ay, MA, Cy, Fy). b. The elastic curve.c. Vertical displacement at B. d. Rotation just to the left of B. e. Rotation just to the right of B.
From the given set of forces shown, the three forces acting on the beam can be replaced with a single equivalent Force R. Determine the following: P,= 25ヒN Pz - 40KN Pa- 80 kN 40° 500 4m Com a. The x-component of the resultant force? b. The magnitude R. c. The corresponding value of e.
2. The figure shows a jam cleat designed for a sailboat where the large friction forces developed by the cams prevent the rope from slipping. Determine the force R supported by each cam bearing from the 900-N rope tension. The coefficient of static friction between the rope and the cams is 0.8. Hint: FBD of one cam only. The line of action of R passes through the point directly above the center of the 80-mm circular cam profile and the center of the cam mounting pin. Ans: R = 1885 N 80 mm. 20 mm 900 N
An extruded beam has the cross-section shown in the figure. A vertical shear force, V of 110 kN is acting at the shear center of the section. Uniform thickness is 9mm. 72 50 192 50 Use I = 22.055484 × 10° mm' Estimate the total vertical shear (kN) resisted by the web CD. A 117 B 110 C 103 D 96 The distance from the axis of the web to the shear center is most nearly equal to. A 35 mm B 20 mm 15 mm D 40 mm
The 300-lb force is to be resolved into components along lines a-a’ and b-b’. 1. Determine the angle α knowing that the component along line a-a’ is 240-lb. 2. What is the corresponding value of force along line b-b’?
A simply supported 4-m long beam is made up of 80% grade Kato. The beam is carrying a uniform load of 12 KN/m all through out its length and a concentrated load of 800 N 1 meter from the left support. The cross-sectional area of the beam is indicated below. *USE 2 DECIMAL PLACES IN EVERY VALUES 1. What is the maximum shear of the beam in KN? (use two decimal places) 2. What is the maximum moment of the beam in KN.m? (use two decimal places) 3. What is the total cross-sectional area of the beam in mm2? (use two decimal places)
Consider the same beam (orientation a) in Q1. If b=20 cm and h = 10 cm, and if the beam material has a maximum allowable stress of 100 MPa, then what is the maximum bending moment the beam can be exposed to? b Case (a) OI. 333.33 N.m O II. 20000 N.m III. 33333.33 N.m O IV. 1000 N.m Neutral axis