2. The pipe connection shown is a series-parallel connection. The rate of flow in pipeline 1 is 300 L/s. Assuming equal values of f-0.02 for all pipes, determine the discharges in pipelines 2, 3, and 4. Q₁ = 300 L/S D₁ = 205 mm L₁ = 300 m D₂ = 205 mm L₂ = 150 m D3 = 205 mm L3 = 75 m 35 D4 = 385 mm L₁ = 75 m Ds = 305 mm Ls = 450 m

2. The pipe connection shown is a series-parallel connection. The rate of flow in pipeline 1 is 300 L/s. Assuming equal values of f-0.02 for all pipes, determine the discharges in pipelines 2, 3, and 4. Q₁ = 300 L/S D₁ = 205 mm L₁ = 300 m D₂ = 205 mm L₂ = 150 m D3 = 205 mm L3 = 75 m 35 D4 = 385 mm L₁ = 75 m Ds = 305 mm Ls = 450 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the flow (m³/s) in each of the pipes shown in the figure. Assume f = 0.02 for all pipes.
The pipeline shown in the figure A. takes water from a reservoir and terminates in a nozzlehaving a jet diameter of 2 inches. With the pipe losses shown in the figure, and assuming anozzle loss of (a) 8.76 %, (b) 10.67 % of the velocity head in the jet. Compute the dischargeand make a table showing the elevation head, pressure head, and total head at each of thesix stations
The total head lost from A to E in the figure shown is 15 m. Find the discharge (m³/s) in each pipe. Assume ? = 0.02 for all pipes.
Pipes 1, 2 and 4 are connected in series with pipes 2 & 3 parallel to each other.Pipelines Diameter Length Friction Factor1 350mm 2500m 0.022 400mm 4000 m 0.023 300mm 2000 m 0.024 450mm 2500 m 0.02If the discharge of pipeline 2 is 0.05 m^3/s,1. Compute the rate of discharge of pipeline 32. Compute the rate of discharge of pipeline 43. Compute the total headloss of the pipe system
A Venturi meter having a throat diameter of 150mm is installed in a 300mm diameter horizontal pipeline carrying oil (S = 0.80). A mercury U-tube connected as shown shows a difference in height of mercury columns of 200mm, the remainder of the tube being filled with oil. If the meter coefficient is 0.95, determine the following: a.)The theoretical discharge (m3/s). Consider HL = 0. b.)The actual discharge (m3/s). Consider HL c.)The head loss (m) between the inlet and the throat.
The orifice in the figure shown is 50mm in diameter and is sharp-edge with Cc= 0.63, and Cv = 0.97. The diameter of the pipe is 150mm. The liquid is water stands at a height h of 2.89m in the piezometer. Compute the discharge, the diameter of the jet and the head loss
Compute the discharges for the pipes of the network shown below. Use the Hardy Cross method. Only one iteration cycle is required. The Hazen-Williams coefficient is 130 for all pipes. Begin your computation with the assumed discharges given below and verify that they satisfy the continuity requirement. QAB = 2.4 cfs (from A to B) QBD = 1.5 cfs (from B to D) QBC = 0.3 cfs (from B to C) QCD = 0.5 cfs (from C to D) QAC = 1.8 cfs (from A to C)
Determine the discharge in pipes 1, pipe 2, pipe 3 and pipe 6 in the system shown if the total head loss from A to B is 100m and friction factor for all pipes is 0.02. a) Discharge in pipe 1 is _____cu.m./s b) Discharge in pipe 2 is _____ cu.m./s c) Discharge in pipe 3 is _____ cu.m./s d) Discharge in pipe 6 is _____ cu.m./s
The head-discharge relationship for a certain pump can be represented by the equation H = 28 - 9Q2. The pump is fixed 2.5 m above the water surface in a river and it forces the water to a tank at a level 10 m above the pump. The suction and delivery pipes are 15 m and 740 m long, respectively and each pipe is 0.5 m in diameter. The pipe coefficient of friction (f)is 0.017. Estimate the discharge (in m3/s) at the best operating point for the pumping system. Q = 0.9 m3/s Q = 1.1 m3/s Q = 0.4 m3/s Q = 0.6 m3/s
If the total flow of 4.0m3/? takes place in the three pipes. Determine the distribution offlow. The pipe lengths, diameters and frictions factors are shown below.
Estimate the transition length in a 3.5-inch SCH 40 pipe, if the Reynolds number of the flow is 2400
A pump is installed in the pipeline between reservoirs A and E as shown in the figure below. Water surface elevations for Reservoirs A and E are 25 ft and 40 ft, respectively. The diameters and lengths of pipes are shown in the figure. The Hazen-Williams coefficients for all pipes are 120. Entrance loss from reservoir A is 0.5 and exit loss from reservoir E is 1.0. The discharge for the pipeline is 10 cfs. The efficiency of the pump is 0.85. Determine the horsepower required for the pump.