Please show all of your work and post pictures of your work, do not type it please! also draw free body diagrams for the problem. THANK YOU FOR YOUR HELP! 6-33. Determine the force in members BC, HC, and HG of the bridgetruss and state if the members are in tension or compression.Prob. 6-333 m|——3 m-HB***-3 m-12 kNCG-3 m14 kN......DF…..-3 m-18 kNE

Determine the force in members BC, HC and HG of the truss.Let's using method of section.

6-33. Determine the force in members BC, HC, and HG of the bridge truss and state if the members are in tension or compression. Prob. 6-33 3 m 3 m- H B *** -3 m- 12 kN C G -3 m- 14 kN ... ... D F ... -3 m- 18 kN E

6-33. Determine the force in members BC, HC, and HG of the bridge truss and state if the members are in tension or compression. Prob. 6-33 3 m 3 m- H B *** -3 m- 12 kN C G -3 m- 14 kN ... ... D F ... -3 m- 18 kN E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A bearing plate is to be designed for a W21x62, A36 steel beam that will sit on a reinforced…

A: The steel section used as bearing plate = W2162The yield strength of steel (fy) = 345 MPaThe…

Q: Determine the internal normal force, shear force, and moment acting at point C and at point D, which…

Q: Critical duration ? 22 O 16 days 18 days 15 days O 17 days ( 3 R 4 53 S 5 U 3 2 NX 2

A: This question is related to the CPM and PERT from Civil Engineering.Find out - Calculate the…

Q: 1. Estimate the maximum wave heights at points A and B in the region behind the breakwater in the…

A: Estimate the wave height at the breakwater. This can be done using the following equation:Hb = Hi *…

Q: Water with sp.gr 0.97 flows through a pipe of uniform diameter 350mm with a mean velocity of 1.0…

A: SG = 0.97 D = 350 mm or 0.35 m V = 1 m/sP1 or 250,000 Pa

Q: 2. Compute the horizontal force P required to prevent the block from sliding down the plane for the…

Q: What did you use for the axis y is the % finer but what is the x axis axis

A: Given:Required:Give the name of x and y axes used in the graph.

Q: 6-34. Draw the shear and moment diagrams for the cantilever beam. Prob. 6-34 8 A -1.5 m- 3 kN.m -1.5…

Q: What change in volume of would 100 mm cube of steel suffer at a depth of 5 km in sea water

A: 100 mm cube of steel. Hence volume of the cube = 1003 = 106 mm3Depth = 5 km = 5000 mm Here Young's…

Q: Determine the magnitude of a force equivalent to the rectangular distributed load and where it acts…

A: (a)(b)To find: (a) Replace the distributed load with single force and its location.…

Q: 1. Identify zero force memeber. (Draw the FBD of Joint contain zero force member) B H|100 kN 60 kN K…

A: Identify the zero force member (Draw the FBD of joint contain zero force member).

Q: Scenario The concrete dam in the figure below is to be built on top of a soil whose profile consists…

A: Solving question 1Given data,question related to geotechnical engineering, FINDa) What will be the…

Q: Water is flowing in a rectangular flume with a velocity of 3.81 m/s and a depth of 0.98m. (a) is the…

Q: A steel column carries an axial load of 785 kN and a moment of 72 kN-m at the top and moment at the…

A: (P/Pn) + (M/Mn) <= 1where:P is the applied axial loadPn is the nominal axial load capacityM is…

Q: Introduction of Specific Gravity Determination

A: This question is related to the Soil Mechanics from Civil Engineering.Ask about - Introduction of…

Q: Compression steel Given: The beam cross-section shown have the following cross-sectional…

Q: Analyze the beam shown below and draw S.F.D and B.M.D. A A E 30 kN-m B x3m 3m² 40KN F с 2 40KN *2mx

Q: A) Determine all the forces of every member and identity members that can be solved by method of…

Q: A staggered bolted connection has bolts arranged as shown. Diameter of bolts is 21 mm. Fy = 248 MPa.…

A: Bolted joints are one of the most well-known components in development and machine plan. They…

Q: of the following statements is true regarding stopping the work on a project? Check all that apply.…

A: Above conditions are regarding stop work order.

Q: A Section 5.4 5.29 through 5.51 Draw the shear and bending moment diagrams and the qualitative…

Q: H.W. 2: Analyze the compound beam shown below with internal hinge at E and F. a. Check stability and…

Q: A W 16 x50 is used as a beans to carry a uniform we and dead load including own weight of 35.7 kN/m…

A: To calculate the maximum bending moment,Mmax = wL2 / 8where:Mmax is the maximum bending moment in…

Q: A canal has a flow rate ranging between 0.1-0.2 m3/sec through a v-notch weir. Determine the max…

Q: How much service live load, in kN/m, can be supported? The member weight is the only dead load. The…

A: Service dead load = 45 kNService live load = 90 kNGross area, Ag = 18400 mm2Radius of gyration, ry =…

Q: A pipe has an outer diameter of 26 mm and an inner diameter of 19 mm. What is the polar moment of…

Q: A simple beam 4.3 m in span carries a concentrated load of 304 kN at its midspan and is subjected to…

A: L = 4.4 mw = 304 kN P = 250 kN Fy = 248 MPa

Q: Hand

Q: riefly outline the process of soil compaction in earthwork sites

A: In earthwork construction, soil compaction plays a crucial role in ensuring the stability and…

Q: An asphalt pavement drains into a rectangular concrete channel. The catchment surface has an average…

A: Average of the slope of asphalt surface, Distance between catchment boundary and drain, Length of…

Q: Drawing B INSTRUCTIONS: USE M12 BOLTS GRADE 4.6/5 INCLUDE BOLT GAUGE DISTANCES AND EDGE DISTANCES…

A: Planning is the process of setting goals, defining strategies, and outlining the steps or actions…

Q: A cubic meter of dry (no water) quartz sand (G, = 2.65) with a porosity of 60% is immersed in an oil…

A: Vt = 1 m3Gs = 2.65n = 60% or 0.60 = 0.92 g/cm3 or 920 kg/m3 Vair = 0.27 m3

Q: What equipment is typically required to conduct a sieve analysis test

A: We need to describe which equipment is typically required to conduct a sieve analysis test

Q: The sludge produced from the aeration tank of the activated sludge process has a solid content of 2%…

Q: Determine the cutting force Fexerted on the rod S in terms of the forces Papplied to the handles of…

Q: Water at 20°C is flowing through through a narrow section as is seen in the figure. There is a 20…

A: Given data:P1-P2=10kPaV2=10m/s

Q: Efflorescence in cement is caused due to an excess of Iron oxide K20 and Na203 Silica Alumina…

A: Efflororscense is the phenomenon in which white coloured precipitate is formed on the surface of a…

Q: What can you learn or insights as an Civil engineering student on the plant visit on La Mesa Dam and…

A: A plant visit to La Mesa Dam and a sewage treatment plant can provide civil engineering students…

Q: 000 100 250b 250b gniblo pud tadt smuez A Ma The rigid pipe is supported by a pin at A and an A-36…

A: Young's modulus, E=200 GPadiameter of the wire, d =6.5 mmload P= 3 kNTo find:stretch the length

Q: 5.Compute the distribution of flows in the pipe network shown in fig below, where the head loss in…

Q: The wide-flange beam is subjected to a shear of V = 18 kN. (Figure 1) Figure Part A A B 200 mm 20 mm…

A: Shear force, V=18kN , To Determine: Maximum Shear Stress in the beam

Q: ● ● From the following measured interior angles of a triangle, calculate the adjusted interior…

Q: depth of 600mm and total depth of 650mm. It is reinforced with 4-32mm diameter bars for tension. fc'…

A: Width of the reinforced concrete beam (b): 300 mmEffective depth of the beam (d): 600…

Q: A simple beam 4.4 m in span carries a concentrated load of 316 kN at its midspan and is subjected to…

A: L = 4.4 mw = 316 kN P = 243 kN Fy = 248 MPa

Q: The 3 day BOD of a sample is 75mg/l with k(base e) is 0.345/day. The amount of BOD remaining in the…

A: Given 3 day BOD 75 mg/lConstant 0.345/dayTo find out BOD after 8 days

Q: The soil of an 21 degree infinite slope is subjected to full depth seepage. The soil properties are…

A: Full depth seepage take place. Determine the limiting depth of slope (Hc).

Q: a building will have a sitting wall on the north side of the building to allow for seating during…

A: wall height = 1.5 meter γdry = 18.3 kN/m^3 γbuoyant =11.5 Kn/m^3 γwater = 9.81 kN/m^3 Φ = 36…

Q: Of new tyres with good treads and worn-out tyres, which one gives higher friction factors in wet and…

A: We need to choose which type of tyres gives higher friction factor in wet and dry condition…

Q: Consider a PERT Network as shown below: 4-6-8 O 28 29 The maximum time required for the completion…

A: Given Activities Pert timeTo find out Maximum time

Q: 10. The 5-kg skateboard rolls down the 5° slope at constant speed. If the coefficient of kinetic…

Concept explainers

Loads and Reactive Forces

Loads are the external influences that a beam experiences under its working conditions. For instance, a beam may be subjected to shear loads, twisting loads, bending moment, and axial loads during its working conditions. Engineers primarily deal with beams and trusses in the civil engineering domain. Due to the influence of loads, it is very crucial to determine the induced stresses and deformation values. These values give an insight into the critical area of the beam that needs to be worked upon to make it fail-safe.

Question

100%

Please show all of your work and post pictures of your work, do not type it please! also draw free body diagrams for the problem. THANK YOU FOR YOUR HELP!

6-33. Determine the force in members BC, HC, and HG of the bridge
truss and state if the members are in tension or compression.
Prob. 6-33
3 m
|——3 m-
H
B
***
-3 m-
12 kN
C
G
-3 m
14 kN
...
...
D
F
…..
-3 m-
18 kN
E

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: State the given data

VIEW

Step 2: Determine the support reaction

VIEW

Step 3: Taking section 1-1 [Left Part]

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine force in member FG
6:44 X Q2-P3-ANALYSIS OF STR... 2 of 2 PROBLEM 2 Û Determine the forces in members GB, GF, GC and BF by the: a). Method of Joints b). Method of Sections чки AKN # W in 3 KN. akn 3m 3m from from from t 3m 624 3 KN 3m
III. Determine the force acting on members GI, AD, and GC: 4 @4m 16m A B D. G 60 kips J K 5@ 3 m 15 m-
2. Determine the force in members EF and EL of the roof truss and state if the members are in tension or compression. 6 kN B 12 kN 12 kN 12 kN 6 m IM IL 12 kN K 12 kN 6 kN -4 m-4m4 m-4 m-4 m-4 m- H T 3m
3-9. Determine the force in each member of the roof truss. State if the members are in tension or compression. Assume all members are pin connected. H 4 m. B 10 KN n4m² C 10 kN + Prob. 3-9 F D 10 kN + -4m- m- 3 3 m 3 m 1
Problem 2 & 3. Determine the force in each member of the truss using method of joints. State if the members are in tension or compression. 40 KN G 3 m 20 kNE 2 m 5m 30 2kN ME 40 kN tati SE Prob. 2 40 kN SE NE m F 20 KN لي - m B Prob. 3
3. Determine the forces in members GF, FC and CD. State if the members are in tension or compression (T or C). 1.5 kN 2 kN 0.8 m A B -1 m 1.70 m H -2m G ... F 2 m D 1.5 m
2. DETERMINE THE FOROE IN MEMBER IJ.BI,GH & IH. STATE WHETHER THE MEMBERS ARE IN TENSION OR COMPRESSION. 1 S00 N Nodo1 5OON SOON SOON 2m
DETERMINE THE STRESS IN EACH MEMBER OF TRUSS LOADED AND SUPPORTED AS SHOWN. - 4m Am 104N D 10 KN 4m Epanels@4m = 20m E B 4m LL G 604N → 60 kN
1000 N 3000 N 1000 N b E b 1000 N F D 30 a В -2 m --2 m-–2 m--2 m 4000 N 2000 N Determine the force in member EB of the roof truss shown by method of sections. Indicate whether the member is in tension or compression.
3-23. Determine the force in members EF, EP,and LK of the Baltimore bridge truss and state if the members are in tension or compression. Also, indicate all zero-force members. M L. K 2 m N. P 2 m A В D E G 2 kN 2 kN 5 kN 3 kN 8 @ 2 m = 16 m- Prob. 3-23
4. Determine the force in members CD and CM of the Baltimore bridge truss and state if the members are in tension or compression. Also, indicate all zero-force members. M K N O P A B C D DE F H 2 kN 2 kN 5 kN 3 KN 16 m, 8 @ 2m 2 m + 2 m