The 200 mm x 150 mm x 12.5 mm angle has one line of 20 mm diameter bolts in each leg. The bolts are 75 mm on center in each line and are staggered 37.5 mm with respect to each other. Fy = 248 MPa, F₁ = 400 MPa. Standard nominal hole diameter of 20 mm bolt is 21 mm. Area of angular section = 4355 mm². Compute the net area of the given section. Compute the effective net area if the reduction coefficient u = = 0.75. 3 Compute the maximum allowable tensile load that the section could carry. mun 87.5 1124 mun 11125 875 625 150 mm 873 1125 875 62.5 173

The 200 mm x 150 mm x 12.5 mm angle has one line of 20 mm diameter bolts in each leg. The bolts are 75 mm on center in each line and are staggered 37.5 mm with respect to each other. Fy = 248 MPa, F₁ = 400 MPa. Standard nominal hole diameter of 20 mm bolt is 21 mm. Area of angular section = 4355 mm². Compute the net area of the given section. Compute the effective net area if the reduction coefficient u = = 0.75. 3 Compute the maximum allowable tensile load that the section could carry. mun 87.5 1124 mun 11125 875 625 150 mm 873 1125 875 62.5 173

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

24) A staggered bolted connection has bolts arranged as shown. Diameter of bolts is 19 mm. Fy = 248 MPa. Calculate the net area (sq. mm) along fracture line passing through bolts 2 and 3 only. Use w = 4.1 mm and t = 12 mm. Write your final answer in whole number
uestion 9 60mm, 60mm -O 1 100mm 2 100mm 100mm 100mm A staggered bolted connection has bolts arranged as shown. Diameter of bolts is 19 mm. Fy = 248 MPa. Calculate the net area (sq. mm) along fracture line passing through bolts 2 and 3 only. Use w = 4.1 mm and t = 12 mm. Write your final answer in whole number
Problem. A bolted connection shown consists of two plates 300 mm x 12 mm connected by 4 - 22 mm diameter bolts. 12 mm bolts T12 mm te12 mm P 300 75 75 75 Edge distances = 75 mm %3D dnole for tensile and rupture = dp +3 mm %3D dnole for bearing strength for Lec = d + 1.5 mm Fy = 248 MPa Fu = 400 MPa %3D En 330 MPa %3D Use LRFD design method. Determine the design strength due to tensile rupture strength of plates. (kN)
Compute the effective net area of the built-up section shown in the figure if the holes are punched for 3/4-in Ø bolts. Assume U=0.90. (Ans. 20.18 in^2)
Calculate the ultimate strength of the angle bar L150x90x8 using resistance factor of 0.75 and Fu = 450 MPa along fracture line b-c. Holes are for 22 mm diameter bolts. Write your final answer to the nearest whole number in KN. 40 40 a 40 b O c 5484 57 63 50.
Determine the Net Area for the following Plate Section consider all possible Cases. The Plate thickness is 1-in. and the bolts' diameter is 7/8-in. s = 6.0 " g = 2.0 "
The tension member shown in the figure contains holes for 3/4-in Ø bolts. At what spacing, s, will the net area for the section through one hole be the same as a rupture line passing through two holes? (Ans. 3.24 in)
The tension member shown contains holes for 3/4 -in Ø bolts. At what spacing, s, will the net area for the section through one hole be the same as a rupture line passing through two holes? 2글 in: 3 in 2 in 8 in
A staggered bolted connection has bolts arranged as shown. Diameter of bolts is 21 mm. Fy = 248 MPa. Calculate the net area (sq. mm) along fracture line passing through bolts 2 and 3 only. Use w = 4.8 x100 mm and t = 16 mm. Write your final answer in whole number 60mm 60mm 100mm 100mm 100mm 1 O 4 2 100mm W
Determine the smallest net area of the tension member shown in the figure. The holes are for 3/4-in Ø bolts at the usual gage locations. The stagger is 1 1/2 in. (Ans. 2.98 in^2)
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 1/2-inch-diameter bolts. Assume the Ae = 0.75An. Section 2L5 x 3 x16 LLBB Determine the allowable tensile strength for ASD. Select one: а. 52.1 b. 104.2 c. 87.8 d. 43.9
= Determine the moment of mertia (1x) of the following built-up sections. Show your calculations. I 3/8" x 7" plate top & bottom W18 X35